Q: For the spring system shown in the accompanying figure, determine the displacement of each node. Start by identifying the size of the global matrix. Write down elemental stiffness matrices, and show the position of each elemental matrix in the global matrix. Apply the boundary conditions and loads. Solve the set of linear equations. Also, compute the reaction forces.

Q: For the spring system shown in the accompanying figure, determine the displacement of each node. Start by identifying the size of the global matrix. Write down elemental stiffness matrices, and show the position of each elemental matrix in the global matrix. Apply the boundary conditions and loads. Solve the set of linear equations. Also, compute the reaction forces.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PConsider the following spring system. with spring constants c 3 Assume down is the positive direction. Write the stiffness matrix K 10 Compute the displacements caused by the external forces f -2 Displacement =
Obtain the stiffness matrix of the two degree of freedom system shown below.
Problem. Consider the following problem. Find the displacement of node 4. Assume F2=200 N, F3=300 N, F4=400 N and Kı= 100, K2= 200, and K3= 300 N/mm. F. 3 2 3 4 Note: The stiffness matrix of individual springs should be first written, then the equilibrium equations at each node should be written, expanded in terms of nodal displacement, and used to perform the assembly of the global stiffness matrix of the problem. Then, the appropriate boundary conditions should be applied and the nodal displacement vector should be found. Every step should be shown; missing any step would result in point deduction even if the final answer is correct.
140 lb 12 lb/in. 8 in. Problem 5-54 what are the values of the reaction forces O r1=150KNM r2=177KN O r1=177KN, r2=150KN O r1=177.9167N, r2=157.0833KN O r1=171.9KN, r2=150KN
For problem on the picture. assume that the left side of the spring has a fixed end and the other side has pull force applied to it. The force applied to the spring is 3lbf. Solve for the following:a. Draw the free body diagram using the equivalent spring constantb. total deformation of the spring
PROBLEMFor the plane truss given below, using the Matrix Stiffness Analysis method, determine;• Determine displacements of the joints• Determine the forces in the truss members• Determine the support reactionsNote that the whole system has 4 nodes and hence 8 degrees of freedom. These degrees of freedomsare shown (in their positive directions) on the right hand side of the problem picture (1 to 8). So, thesystem stiffness matrix, K, will be 8x8 in size.Force and displacement units should be consistent (mm’s and N’s for example)
Using the node method and using matrices in Matlab, determine the force on each element of the armature shown in the following figure. Set whether the elements are in tension or in compression. Also calculate the reactions in the supports. Number the nodes and the elements and pose the sum of forces in X and Y in each of the nodes, including the supports. To propose the equations consider that all the elements are in tension (positive value), if the result is negative it means that they are in compression. The same with the reactions. The unknowns are the forces in the elements and the reactions, the known values are the applied loads. 6-6. Determine the force on each element of the weapon-lasts and establish whether the elements are in tension or in compression. Consider P1 = 2 KN and P2 = 1.5 KN. 30° 3 m P₁ 30° 3 m
- For the spring system given in Figure 1, Create the element matrices as well as the global stiffness and force matrix, note that k=1. Figure 1
The système have diferent stiffness (K1 and K2), The column (AB) have both ends pined and the Beam (BC) have one end pined and one end fixed. Find the system équation of the Residual force of the structure (out of balance force), and the Buckling load.
Q4: For the spring assemblages shown in Figures, determine the node displacements, the forces in each element, and the reactions. Use the direct stiffness method for all problems. Su0 KN) m 4 3 3 3 SuokNm suo KNIM 2. Suo EN/m 13 ZEN
Calculate the reaction forces on the bearing near the pulley and bearing at the far end of the shaft. Include a free body diagram and coordinates. Given the shaft length is 1 meter= Mass=40Kg Static load = 8600N Dynamic (running load) = 8400N Some hints:1. This solution will require you to draw known forces and find unknown reactions in 2perpendicular planes and then add the horizontal and vertical reaction forces asvectors to find the reaction force (hypotenuse).2. Bearings are usually mounted as near as possible to the ends of the shaft withoutfouling the other machine elements. The bearing at the far shaft end can be mountedat the 1 meter point. The bearing at the pulley end should allow clearance to assemblethe pulley.3. Bearing reaction forces are typically simplified as a single point load through thebearing centre.
i.Considering the rod diagrammed below; calculate an equivalent spring constant or the rod using the length of the rod 1, its area A, and Young's nodulus E for a compressive force F that compresses the rod a distance x. Additionally, is a linear spring a useful model for a rod under compression? What if the rod is under tension? compressed rod