PrOVIde ue come We want to design an experiment to measure oscillations of a simple pendulum on the surface of Jupiter with acceleration due to gravity g 30 ms2 We have to make do with a rudimentary video camera with a frame rate of 15 Hz to record oscillations in a pendulum and use it to measure the frequency of oscillation. The smallest length of the pendulum that we can send so that the correct oscillation frequency can be measured is cm. Assume perfect spatial resolution of the camera and ignore other "minor" logistical difficulties with this experiment.

PrOVIde ue come We want to design an experiment to measure oscillations of a simple pendulum on the surface of Jupiter with acceleration due to gravity g 30 ms2 We have to make do with a rudimentary video camera with a frame rate of 15 Hz to record oscillations in a pendulum and use it to measure the frequency of oscillation. The smallest length of the pendulum that we can send so that the correct oscillation frequency can be measured is cm. Assume perfect spatial resolution of the camera and ignore other "minor" logistical difficulties with this experiment.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Dtes 6) Take a look at the picture below. Initially the system is at rest. The spring is activated and sends the mass moving with tangential speed "v" and the disk rotating with angular velocity "w". Find expressions for these parameters in terms of the variables given. Final I nitind At Rest Dişk Rolutes Sprivag: compressx a mass と szring Cons & ingetid velocty muss Rotafiond ふnertiu ofDk
A particle moves with a simple harmonic motion through space. it takes 5ms to complete one cycle. What is its frequency in rad/s ?
A particle vibrates through space. It took 3ms to complete one cycle. What is its frequency in Hz?
1 An object of mass 125 kg is released from rest from a boat into the water and allowed to sink. While gravity is pulling the object down, a buoyancy force of times the weight of the object is pushing the object up (weight = mg). If we assume that water 40 resistance exerts a force on the object that is proportional to the velocity of the object, with proportionality constant 10 N-sec/m, find the equation of motion of the object. After how many seconds will the velocity of the object be 90 m/sec? Assume that the acceleration due to gravity is 9.81 m/ sec2. Find the equation of motion of the object. X(t) = %3D
(2) lahai Q1-e) Kinetics: is used to predict the motion caused by given forces or to determine the forces required to produce given motion True False
An electric motor's torque is a function of the speed at which it rotates. Many brushed AC motors have a linear toque curve as shown below. If the power output of the motor is equal to the torque (T) multiplied by the rotational speed in rad/s (w), what is the maximum power you can get out of the motor if the stall torque (Tstall) is 0.001 Nm and the no load speed (wno load) of 14,332 RPM? Give your answer in Watts. There are two ways to solve this: Use a stall torque and no load speed and plot the torque profile below and then plot the power versus rotational speed to find the maximum. The second method is to determine the mathematical relationship for power given the information at the start of the question and set the differential of power with respect to RPM equal to zero, and solve for the RPM to get the maximum. Tstall Wno load W
Problem Solving: )An object falls from rest in a medium offering a resistonce. The velocity of the object hefore the ohject reaches the ground is given by the differential egua- tion dv/t + V% = 32, t/sec. uhat is the veloaty of the okject one second after it falls ?
62. •A 5-kg object is constrained to move along a straight line. Its initial speed is 12 m/s in one direction, and its final speed is 8 m/s in the opposite Complete the graph of force versus time with direction. F (N) (s) appropriate values for both variables (Figure 7-26). Several answers are correct, just be sure that your answer is internally consistent. Figure 7-26 Problem 62
A chamber of unknown volume is filled with an unknown amount of ideal gas. A cylinder with an open bottom and calibrated volume is connected to the chamber and is closed with a movable piston. A gas pressure sensor is also mounted on the chamber as shown in the figure. The whole experimental setup is kept at a constant temperature of 300 K. Doris moves the piston from mark 0 to mark 200 mL in steps of 50 mL and records the corresponding pressure in the chamber (see the table below). She moves the piston very slowly and waits several minutes before recording the pressure values. VCyl(mL) P(105N/m2)) 0 4.35 50 3.85 100 3.50 150 3.15 200 2.90 Determine the volume of the chamber using Doris's data in the table. (Note: This is a problem that requires linearization of data.) Determine the number of moles of gas. (Note: This is a problem that requires linearization of data.)
Context The needle of a sewing machine makes a repetitive up and down motion which is described by the equation y(t)=Acos(wt) To choose the settings of the device that will ensure that the needle successfully pierces the textile, you are asked to model the speed in ? of the needle as a function of time. Constraints and information The parameter A represents the range of motion (in m);The parameter w represents the angular frequency. It tells us about the number of back and forth movements that the needle makes per second;The parameter w is given in rad/s, so your calculator absolutely must be in radians mode to do the calculations in this problem;Modelization Establish the model for the y velocity of the needle as a function of time and the parameters A and w. Then test your model by calculating the speed in y of the needle at the moment and with the given parameters: Moment: 4.1 s Amplitude: 0.012 m Angular frequency: 17.9 rad/s
A block has a velocity described as v = 0.2cos20t, what is displacement of the %3D block after 3 s?
An object attached to a spring undergoes simple harmonic motion modeled by the differential equation d²x = 0 where x (t) is the displacement of the mass (relative to equilibrium) at time t, m is the mass of the object, and k is the spring constant. A mass of 3 kilograms stretches the spring 0.2 meters. dt² Use this information to find the spring constant. (Use g = 9.8 meters/second²) m k = + kx The previous mass is detached from the spring and a mass of 17 kilograms is attached. This mass is displaced 0.45 meters below equilibrium and then launched with an initial velocity of 2 meters/second. Write the equation of motion in the form x(t) = c₁ cos(wt) + c₂ sin(wt). Do not leave unknown constants in your equation. x(t) = Rewrite the equation of motion in the form ä(t) = A sin(wt + ), where 0 ≤ ¢ < 2π. Do not leave unknown constants in your equation. x(t) =