Problem 3 In class, we solved for the vorticity distribution for a "real" line vortex diffusing in a viscous fluid. Integrate this vorticity distribution to find the tangential velocity as a function of radius. Plot the velocity distributions for a a line vortex of circulation 0.5 mls in 20 °C air for times of 1, 10, and 1 seconds.

Problem 3 In class, we solved for the vorticity distribution for a "real" line vortex diffusing in a viscous fluid. Integrate this vorticity distribution to find the tangential velocity as a function of radius. Plot the velocity distributions for a a line vortex of circulation 0.5 mls in 20 °C air for times of 1, 10, and 1 seconds.

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter7: Arrays

Section7.5: Case Studies

Problem 15E

See similar textbooks

Similar questions

An aluminum wire having a cross-sectional area equal to 4.60 x 10-6 m? carries a current of 7.50 A. The density of aluminum is 2.70 g/cm³. Assume each aluminum atom supplies one conduction electron per atom. Find the drift speed of the electrons in the wire. 1.95E-4 The equation for the drift velocity includes the number of charge carriers per volume, which in this case is equal to the number of atoms per volume. How do you calculate that if you know the density and the atomic weight of aluminum? mm/s
2. Heat conduction in a square plate Three sides of a rectangular plate (@ = 5 m, b = 4 m) are kept at a temperature of 0 C and one side is kept at a temperature C, as shown in the figure. Determine and plot the ; temperature distribution T(x, y) in the plate. The temperature distribution, T(x, y) in the plate can be determined by solving the two-dimensional heat equation. For the given boundary conditions T(x, y) can be expressed analytically by a Fourier series (Erwin Kreyszig, Advanced Engineering Mathematics, John Wiley and Sons, 1993):
For an object of mass m=3 kg to slide without friction up the rise of height h=1 m shown, it must have a minimum initial kinetic energy (in J) of: h O a. 40 O b. 20 O c. 30 O d. 10
Suppose that a parachutist with linear drag (m=50 kg, c=12.5kg/s) jumps from an airplane flying at an altitude of a kilometer with a horizontal velocity of 220 m/s relative to the ground. a) Write a system of four differential equations for x,y,vx=dx/dt and vy=dy/dt. b) If theinitial horizontal position is defined as x=0, use Euler’s methods with t=0.4 s to compute the jumper’s position over the first 40 s. c) Develop plots of y versus t and y versus x. Use the plot to graphically estimate when and where the jumper would hit the ground if the chute failed to open.
Q4: Write the parametric equation of revolution surface in matrix form only which generated by rotate a Bezier curve defined by the coefficient parameter in one plane only, for the x-axis [0,5, 10,4], y-axis [1,4,2,2] respectively, for u-0.5 and 0 = 45° Note: [the rotation about y-axis].
1. Determine the equation of the line through the given point (a) parallel and (b) perpendicular to the given line Given: Point: ( -1,-4) Line: 4x-2y=3
2. calculates the trajectory r(t) and stores the coordinates for time steps At as a nested list trajectory that contains [[xe, ye, ze], [x1, y1, z1], [x2, y2, z2], ...]. Start from time t = 0 and use a time step At = 0.01; the last data point in the trajectory should be the time when the oscillator "hits the ground", i.e., when z(t) ≤ 0; 3. stores the time for hitting the ground (i.e., the first time t when z(t) ≤ 0) in the variable t_contact and the corresponding positions in the variables x_contact, y_contact, and z_contact. Print t_contact = 1.430 X_contact = 0.755 y contact = -0.380 z_contact = (Output floating point numbers with 3 decimals using format (), e.g., "t_contact = {:.3f}" .format(t_contact).) The partial example output above is for ze = 10. 4. calculates the average x- and y-coordinates 1 y = Yi N where the x, y, are the x(t), y(t) in the trajectory and N is the number of data points that you calculated. Store the result as a list in the variable center = [x_avg, y_avg]…
The following is used to model a wave that impacts a concrete wall created by the US Navy speed boat.1. Derive the complete piecewise function of F(t) and F()The concrete wall is 2.8 m long with a cross-section area of 0.05 m2. The force at time equal zero is 200 N. It is also known that the mass is modeled as lumped at the end of 1200 kg and Young’s modulus of 3.6 GPa2. Use *Matlab to simulate and plot the total response of the system at zero initial conditions and t0 = 0.5 s
(Conversion) An object’s polar moment of inertia, J, represents its resistance to twisting. For a cylinder, this moment of inertia is given by this formula: J=mr2/2+m( l 2 +3r 2 )/12misthecylindersmass( kg).listhecylinderslength(m).risthecylindersradius(m). Using this formula, determine the units for the cylinder’s polar moment of inertia.
Q1: Consider a surface of revolution generated by a Bezier curve defined by the four control points P(0,0,0), (2,1,2), P₂ (3,3,0) P, (2,2,3) respectively, rotating about the X-axis. Calculate the point on the surface at u = 0.25, 0= π/2.
Solve the following equations. Be sure to check the potential solution(s) in the original equation, to see whether it (they) are in the domain. (a) log, (r? –x – 2) = 2
A 200 gallon tank initially contains 100 gallons of water with 20 pounds of salt. A salt solution with 1/5 pound of salt per gallon is added to the tank at 10 gal/min, and the resulting mixture is drained out at 5 gal/min. Let Q(t) denote the quantity (lbs) of salt at time t (min). (a) Write a differential equation for Q(t) which is valid up until the point at which the tank overflows. Q' (t) = = (b) Find the quantity of salt in the tank as it's about to overflow. esc C ✓ % 1 1 a 2 W S # 3 e d $ 4 f 5 rt 99 6 y & 7 h O u * 00 8 O 1 9 1 O