Problem 2 For the system shown in Figure 12.5: a) Find Is. b) Find the average power delivered to each element. c) Find the reactive power associated with each element. d) Find PT, QT, and ST. e) Find the power factor seen by the source E. R₁ ww 392 + E = 50 V/60° R3 ww 492 R₂ 12 Ω Χ 16Ω Xc 802 Figure 12.5

Problem 2 For the system shown in Figure 12.5: a) Find Is. b) Find the average power delivered to each element. c) Find the reactive power associated with each element. d) Find PT, QT, and ST. e) Find the power factor seen by the source E. R₁ ww 392 + E = 50 V/60° R3 ww 492 R₂ 12 Ω Χ 16Ω Xc 802 Figure 12.5

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is
"If lab is equal to 595.8252306 and lb is 344296, the phase sequence is:" O POSITIVE O NEGATIVE
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
When a resistor is connected across the terminals of an ac generator (117 V) that has a fixed frequency, there is a current of 0.332 A in the resistor. When an inductor is connected across the terminals of the same generator, there is a current of 0.365 A in the inductor. When both the resistor and the inductor are connected in series between the terminals of this generator, what is (a) the impedance of the series combination and (b) the phase angle between the current and the voltage of the generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number (b) Number Buda i Vrms R Irms.R Circuit 1 Units Units Vrms. Irms, L Circuit 2 > L Vrms R www Circuit 3
2. The pu impedance of a circuit element is 0.15. If the base kV and base MVA are halved. Then the new value of pu impedance of the circuit element is A. 1.2 C. 1.1 3. The pu impedan B. 1.0 B. ambient tempera- ture D. 0.8 E. none
The average value of sinusoidal varying voltage is more than its r.m.s. value. Select one: O True O False Which of the following formula is CORRECT? a. E= - L d0/dt O b. E = - N dl/dt O . L= NI / O O d. W = 0.5 12L In a step down transformer, number of turns in the primary winding is lesser than the number of turns in the secondary winding. Select one: O True O False
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
Impedance of AC circuit and Admittance of AC circuitSHOW THE CIRCUIT USING ANY SOFTWARE OR YOU CAN DRAW IT MANUAALYY thNAKSS
According to the Reactive Power Compensation Regulation, capacitive reactive power should not exceed what percent of active power in the power plants whose power is greater than 50 KVA?
An inductor and a resistor are connected in series with a function generator. The voltage across the inductor is 10.6V pk. The voltage across the resistor is 3.6V RMS. Calculate the magnitude of the total voltage applied to the circuit.
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms