Problem 2: A rigid bar AB as shown in Figure SM – 011 is supported by two vertical rods. The bar AB is 6 m long and is horizontal before the load P = 50 kN is applied. 1. Compute the value of x so that both rods have the same axial stress.. 2. Compute the stress in each rod for that value of x in question 1. steel L = 4 m A = 300 mm? E = 200 GPa Aluminum L= 3 m A = 500 mm? E = 70 GPa A B

Problem 2: A rigid bar AB as shown in Figure SM – 011 is supported by two vertical rods. The bar AB is 6 m long and is horizontal before the load P = 50 kN is applied. 1. Compute the value of x so that both rods have the same axial stress.. 2. Compute the stress in each rod for that value of x in question 1. steel L = 4 m A = 300 mm? E = 200 GPa Aluminum L= 3 m A = 500 mm? E = 70 GPa A B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C P Steel: A=900 mm² E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the value of P without exceeding the allowable stress of bronze, in kN? 174 145 161 124
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P = 3000 Ib and the cross sectional area of the rod is 0.5 in^2, determine the stress in each section. Steel Bronze 4P | Aluminum | P 2 ft 3 ft 2.5 ft а. Stress (st) = 19 ksi, Stress (al) = 25 ksi O b. Stress (st) = 16.5 ksi, Stress (al) = 24.2 ksi O c. Stress (st) = 24 ksi, Stress (al) = 18 ksi O d. Stress (st) = 26 ksi, Stress (al) =17 ksi
An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2= 1.0 m; B3= 0.6 m. Determine the axial stress of bar B3 in MPa. 35KN B1 B2 B3 10KN 15KN 30KN
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. b C P Steel: A = 900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0m E= 200 GPa L = 1.5m What is the value of P without exceeding the allowable stress of steel, in kN? 250 340 280 O230
An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B2 = 1.0 m; B; = 0.6 m. Determine the axial stress of bar B3 in MPa. 35KN B1 B2 B3 10KN 15KN 30KN A) 218.75 в) 125 62.5 D 31.25
A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the compressive stress in MPa? I am new to the subject but why use .....AC = π * (D2 - d2) / 4 instead of A = π(r12 - r22) to find the cross sectional area of a hollow cylinder ?.
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B; = 0.8 m; B; = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 B3 10KN 15KN 30KN
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. a b C Steel: A-900 mm E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? 0.367 0.433 0.467 0.333
2. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free. What is the largest load P that can be applied without exceeding stresses of 160 MPa in the steel rod and 65 MPa in the bronze rod? - 2.5 m 2 m 2 m Steel A=1000 sq. mm Bronze A=400 sq. mm E=200 GPa E=83 GPa L=1.6 m L=2.2 m P
A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two- dimensional stress, o =310 N/mm2 (tensile) and Oy=300 N/mm² (compressive). E=2x105 N/mm², Poisson's ratio μ-0.3. The elongation of the bar is the direction of a will be
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C NANTSELEINE Steel: A = 900 mm² E = 200 GPa L=1.5m Bronze: A=1200 mm² E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? O 0.367 O 0.433 O 0.467 0.333