PROBLEM 14: A container, in the form of an inverted right-circular cone, is 900 mm across the top and 1.2 m high. It contains oil (s=0.86) at a depth of 750 mm. Determine the mass and weight of oil in the container. 900 mm 750 mm 1.2 m
Q: 1. Two streams of water are mixed steadily as shown in the figure below. Find the exit velocity if…
A: Given data: Volumetric flow rate of stream 1, V1 = 0.06 m3/s Mass flow rate of stream 2, m2 = 70…
Q: 1. Consider a particle of mass m which can move freely along the x axis anywhere from x = -a/2 to x…
A: DISCLAIMER FOR MULTIPARTSince you have posted a question with multiple sub-parts, we will solve…
Q: The applied torque on shaft CD is T' = 95 N·m. The journal bearings B, C, and D allow free rotation…
A:
Q: For the system shown above, Assume it is fixed at A. 1. Draw a Free Body Diagram. 2. Determine the…
A: According to the given data provided in the question. A loading Aligned beam as provided in the…
Q: A Gasoline line is connected to a pressure gage with a double-U manometer as shown in the figure.…
A: According to the question data h1=23cm=0.23m h2=8cm=0.08m We need to find Pressure at point A
Q: For a drilling operations, the feed per revolution is 0.07 mm / rev and the spindle speed is…
A: According to the given data The feed per revolution f=0.07mm/rev Spindle speed N=7650 rpm We need to…
Q: How is toughness depicted in the stress-strain curve? Gradient of the curve Maximum stress Fracture…
A:
Q: The rod AB is attached to collars at its ends by ball-and-socket joints. Collar A has a velocity vA…
A: It is required to determine the velocity of the collar B. Consider the diagram as shown below for…
Q: When the blocks are released, determine their acceleration, the tension of the cable, and also the…
A: Givent=1.5smA=10 kgm=25 kg
Q: A ball is released from the bottom of an elevator which is travelling upward with a velocity of 6…
A: Given data: The initial velocity of a ball is, u = 6 m/s The time taken by the ball to strike the…
Q: A 10 Nm torque drives Gear A, which in turn drives a generator via mesh Gear B. What is the speed of…
A: GivenTA=10 NmNB=1500 rpm
Q: Aluminum bars AB and AC have diameters of 10 and 8 mm respectively. Determine the maximum load P…
A:
Q: A beam is loaded and supported as shown below. Using the integration method, determine (a) The…
A:
Q: 1) Express force Fd as a vector in the coordinate system. 2) Express the moment about Point O due to…
A:
Q: At the instant shown, cars A and B are travelling at the speeds shown. If B is accelerating at…
A:
Q: Bar AB has the angular motions shown. Suppose that WAB 3 rad/s and a AB-6.5 rad/s (Figure 1)
A:
Q: Q3. Beam OA is supported by a ball and socket joint at O and Cables AB and AC. If a 150 N force is…
A: In order to find out the forces acting on the tension support, assume a tension in the cable and…
Q: Suppose that P₁= 540 lb and P₂ = 720 lb. (Figure 1) gure M B 4 ft Part A ▾ FBC= Determine the force…
A:
Q: Write the constitutive law for a material with linear elastic anisotropic behavior under mechancial…
A: An anisotropic material is one that has different mechanical properties in different directions.…
Q: The truss above is designed in such a way that all compression and tension members have an area of…
A: According to the question data A loading structure ABCDEFG is given compressive member area=400mm2…
Q: AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume…
A:
Q: A hollow circular shaft 20mm thick transmits 294 kW at 200rpm.Determine the diameters of the shaft…
A:
Q: QUESTION 9 The slider block C moves at 5 m/s down the inclined groove. Determine the angular…
A:
Q: power available at sea-level PA; 0 = 140 kW wingspan b = 11 m wing area S = 16 m2 zero-lift drag…
A: To Find : The maximum rate of climb at sea level and at altitude 5000 m Given : The Power available…
Q: 24 You want to cool air from 150°C to 60°C but you cannot afford a custom-built heat exchanger. You…
A: T1= 150°C T2= 60°C Mass Flow rate of of NH3 vapor = 136 kg/min T3= 200°C T4= 100°C Mass Flow rate…
Q: The box slides down the slope described by the equation y = (0.05x^2) m, where x is in meters. If…
A: This question is based on the concept of kinematics.
Q: A spark ignition cycle having a compression ratio of 9. The air intake is at 100kPa and 20°C, the…
A:
Q: 4. An ideal gas in a piston/cylinder arrangement is cooled in an irreversible process. As its…
A: An ideal gas in a piston/cylinder arrangement is cooled in an irreversible process. As its…
Q: Two identical plates are connected by two 10-mm diameter rivets as shown. Consider the following…
A:
Q: Consider a flat plate subject to parallel flow (top and bottom) characterized by u = 5 m/s, To= 20…
A: Given: The velocity of flow, u = 5 m/s The temperature of flow, T = 20 C The length of the plate, L…
Q: Given the following specifications of a standard fink truss: Cross Section of all the Truss Members:…
A:
Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…
A:
Q: (iii). Aerated water flows through a cylindrical tube of inner radius 1 cm. The tube wall is porous…
A: iii. We can use the equation for mass transfer through a porous tube to estimate the mass transfer…
Q: Problem 1: Draw the shear force and bending moment diagrams for the beam. 600 lb/ft -3 ft- 600 lb/ft…
A: We will 1st draw FBD of the beam , then we will draw shear force & bending moment diagram of the…
Q: The rocket shown is designed to test the operation of a new guidance system. When it has reached a…
A: Given data: M=2.49 Mgθ=34°m=130 kg/sV=625 m/sg=9.54 m/s2 It is required to determine the normal and…
Q: 2) Water cooled steam condenser receives exhaust from multi-stage turbine at saturation temperature…
A: Steam condenser saturation temperature T = 40 °C. Inlet condition of cooling water T1=20 °C outlet…
Q: Both C's in a parallel-flow heat exchanger are equal to 156 W/K, U 327 W/m²K and A = 2 m². The hot…
A: Given that: Ch = Specific heat of hot fluid = 156 W/K Cc = Specific heat of clod fluid = 156 W/K…
Q: Consider the pipe assembly in (Eigure 1) (301+351-30k) N (60i 10-15k) N F₁ F₂ Figure 0.8 m 1.20 m 04…
A: Given data F1= (30i+35j-30k)N F2 = (60i-10j-15k)N Find the moment of force F1 and F2 about point O…
Q: Consider sampling input cosine functions, with a sample rate of 100Hz. (e) Give the values at the…
A: To Find : e) The value at the samples times if you are sampling a sine function that is oscillating…
Q: 12 mx 10 5 The above refrigeration system uses R-12 as the refrigerant, determine: 1. Enthalpies at…
A:
Q: Q.1) Draw a Free Body Diagram for each object indicated below. Include values for known forces and…
A: (a) Draw the given diagram. Now, draw the free-body diagram of member ABD.
Q: 800 N 1200 N·m IT -1 m 1 m 1 m 600 N -1m- Draw the shear and moment diagrams for the beam. Label all…
A:
Q: Determine the force in the member AD of the truss and state if the member is in tension or…
A: Given: To find: Forces in all members
Q: 3 - The strain gauge rosette indicated in the figure provides the following readings:&o= 400μ,…
A:
Q: What is non-equilibrium steady state? And what is the difference between non-equilibrium steady…
A: This question is based on the concept of equilibrium and non equilibrium state.
Q: Problem 2.3 The following problem can be solved using the generalized conservation and accounting…
A: According to Bartleby guidelines we can solve only three subparts of a question at a time. Please…
Q: The amount of fuel introduced into a spark-ignition engine is used in part to control the power…
A: Solution: Given Data: HV=42000 kJ/kgr=8 To Find: (a) Mass of gasoline consumption per sec.
Q: 4. Air at 25°C blows over a heated steel plate with its surface maintained at 200°C. The plate is 50…
A: Given data Convective heat transfer coefficient = 20W/m2K Thermal conductivity = 45 W/mK Air…
Q: A closed cylindrical vessel 5 ft in diameter and 6 ft high is 3/4 filled with molasses (SG = 1.24)…
A: Given data: Diameter of cylindrical vessel = 5 ft Height of cylindrical vessel = 6 ft The vessel is…
Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 720…
A:
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.5.Capillary rise in the glass tube used for measuring water level is not to exceed 0.5 mm. Determine its minimum size, given that surface tension for water in contact with air = 0.07112 N/m.The total pressure force of a square plate is 25 kN, placed vertically in water so that the center of the plate is 1.5 m below the free surface. Determine the size of the plate and the depth of center of pressure. The above square plate is taken out of the water which weighs 370.5 N in air and 180.3 N in water of specific gravity 0.99. Find the volume and specific gravity of the square plate. Draw a neat sketch.
- A cylindrical object 85mm diameter, 157mm height and a mass of 601g, is placed in the tank, which contains oil(51mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 966 kg/m³. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.The cylindrical tank with hemispherical ends contains a volatile liquid and its vapor. The liquid density is 800 kg/m3 and its vapor density is negligible. The absolute pressure in the vapor is 120 kPa, and the atmospheric pressure is 100 kPa. What is the height h (in mm) of the mercury (γ =13.6) on the manometer? a. Not listed b. 171.3 c. 208.7 d. 246.2 e. 187.6 f. 193.7A 98.43ft vertical column of fluid (density is 1878 kg/m3) is located where is 31.66ft/sec2. determine the pressure at the base of the column in kPa.
- 1. Determine the hydrostatic force acting on a vertical trapezoidal section whose upper base is flushed parallel to the liquid surface. The top base measures 2 m and the lower base is twice the length of its top. One of its remaining side is upright vertical while the other is inclined 45° with the horizontal. Calculate as well the location of its center of pressure. 6 m 2. The tank shown contains alcohol (SG=o.78) and covered by a diameter Calculate the bydrostatic force EA barrel in the form of a frustum of a cone with a radius of 3m and 6m at the bottom and at the top respectively. It is 5m high and is 4/5 full of oil (0.83). Determine the a. Total hydrostatic force "F" acting on the wall of the barrel in kN and b. its line of action "s" from the bottomA closed vessel 1 m in diameter is completely filled with water. If the vessel is rotated at 1200 rpm, what increase in pressure will occur at the top of the tank at the circumference? Ans. 1970 kPa
- The given Figure is shown a curve surface. It is required to determine the magnitude, direction, and line of action of the vertical component, the horizontal component, and the resultant hydrostatic force acting on the surface in case () is 1.3 m, specific weight of water is 9770.5 N/m3, and width of the curve is 1.8 m. 1. B Water (write here only FH with two numbers after the decimal xxxxx.xx) for full answer use the pdf file 719The end plates (isosceles triangles) of the trough shown to the right were designed to withstand a fluid force of 6400 lb. Assuming the density of water is 62.4 lb/ft³, how many cubic feet can the trough hold without exceeding this limitation? What is the value of h, the depth of water that exerts a fluid force of 6400 lb? What is the integral that gives the fluid force exerted on the end of the trough when filled with water to a depth of h? h Sody The maximum volume is ft³. (Round down to the nearest cubic foot.) The value of his (Round to two decimal places as needed.) (-3,14) (0,h) y (ft) (3,14) 14 y 3x x (ft) 0 End view of trough 14 ft 30 ft 6 ft → Dimensional view of troughM1 U5: Use the general solution in determining the total hydrostatic force acting on the submerged curved surface. Please provide the complete UNITS ANALYSIS, USE OF CORRECT CONVERSION RATIOS and DIAGRAMS in your hand-written solution. INCOMPLETE/NO SOLUTION means NO CREDIT. Encode your FINAL answer in the space provided after each question. A curved surface is formed as a quarter of a circular cylinder with R = 0.75 m as shown. The surface is w 3.55 m wide. Water stands to the right of the curved surface to depth H = 0.60 m. seawater 0.60 m (SG = 1.03) %3D 0.75 m Determine the magnitude and direction of the horizontal component of the hydrostatic force (in N) acting on the gate. Indicate the direction by putting an R for right and L for left after your numerical answer. Your answer