Problem 1 In a Rankine Thermodynamic cycle, steam leaves the boiler and enters the turbine at 600 psia, 800 °F. The condenser pressure is 1 psia. After presenting a schematic of the problem in addition to clearly labeled and explained T-s and h-s diagrams, you are asked to determine the following: (a) Pump work required per lbm of working fluid. (b) Quality of fluid at turbine inlet. (d) (e) (f) Work output of turbine per lbm of working fluid. Energy input to the boiler per lbm of working fluid. Heat rejection by the condenser per Ibm of working fluid. Determine the cycle thermal efficiency.

Problem 1 In a Rankine Thermodynamic cycle, steam leaves the boiler and enters the turbine at 600 psia, 800 °F. The condenser pressure is 1 psia. After presenting a schematic of the problem in addition to clearly labeled and explained T-s and h-s diagrams, you are asked to determine the following: (a) Pump work required per lbm of working fluid. (b) Quality of fluid at turbine inlet. (d) (e) (f) Work output of turbine per lbm of working fluid. Energy input to the boiler per lbm of working fluid. Heat rejection by the condenser per Ibm of working fluid. Determine the cycle thermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Superheated steam at 18 MPa, 560 °C enters the steam turbine. The pressure at the exit of the turbine is 0.06 MPa and saturated liquid water leaves the condenser at 0.06 MPa. Pressure is increased to 18 MPa again after the pump. Find: (a) Sketch the process on a T-s diagram. (b) The net work per unit of steam flow in kJ/kg. (c) Heat transfer to steam passing through the boiler, in kJ/kg.
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the firstturbine until it is just dry saturated, then it is re-heated to 400 °C and expandedthroughthe second-stage turbine. The condenser pressure is 0.04 bar. Determine the specific work output of the system to 3 d.p? what is the specific entalphy in kJ/kg for state 2?
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the first turbine until it is just dry saturated, then it is re-heated to 400 °C and expanded through the second-stage turbine. The condenser pressure is 0.04 bar. Low-P High-P turbine turbine Reheater Boiler P4 = P3 = Prcheat Condenser find thespecific heat inputof the systemin kJ/kg to 2.d.p. ?
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the first turbine until it is just dry saturated, then it is re-heated to 400 °C and expanded through the second-stage turbine. The condenser pressure is 0.04 bar. High-P turbine Low-P turbine Reheater - Boiler P4= P3 = Preheat Condenser Determine thespecific work outputof the system to 3 d.p.?
Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
As shown below, a refrigeration cycle condenses a flow of ammonia from a saturated vapor at 4 barto a saturated liquid. The entering volumetric flow rate of the ammonia is 0.1 m3/s. The ammonia functions asthe cold reservoir for the refrigeration cycle, and the hot reservoir is at 25 ∘C. A faded specification sheet for therefrigeration cycle reads that the required power input is 35 kW.(a) Is this cycle possible? Why or why not?(b) If the cycle is impossible, how much work input is required to make the cycle
Task (4) Critically compare how the changes of the heat transfer efficiency will affect the lifetime of the turbine.
Unit No. 6 at The Geysers produces 52 MW of power at the generator from a steam flow of 417,000 kg/h at a pressure of 6.9 bar and a temperature of 182°C. The reservoir conditions are known to be 32.3082754 bar and 238°C. The turbine exhaust pressure 2. (condenser pressure) is 0.13 bar. (a) Sketch the location of the reservoir and turbine-inlet state points on the attached Mollier chart (h-s). The requested states should be placed on this h-s diagram. What do you observe about the enthalpy of these two states? What do you notice about these values relative to the maximum enthalpy along the saturated vapor line? (b) On the same diagram, locate the turbine exhaust state. Calculate the turbine isentropic expansion efficiency, 71. Calculate the overall geothermal energy utilization efficiency, 7u, based on (i) reservoir and (ii) turbine-inlet conditions. A sink temperature of 48°C is appropriate for Unit No. 6.
High-P turbine Low-P turbine Reheater 4 Boiler P4 = P3 = Prcheat Pump Condenser The following data was given for a steam Click Save and Submit to save and submit. Click Save All Answers to save all answers. The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m³/kg 3 Find the dryness fraction of steam at state 6 to 1 decimal places.
A medium size power station is used to produce 30 MW net power for arefinery. The station uses steam as the operating fluid and operatesaccording to the Carnot cycle between the pressure limits of 0.4 bar and35 bar. Steam enters the boiler as a saturated liquid and leaves it as adry saturated vapour. (i) List the name of the four processes in a generic Carnot cycle andstate what type of energy transfer (work/heat) can be neglectedin each process. (ii) Determine the dryness fraction of the steam that is fed to thecondenser, and the specific enthalpy values at the four key points ofthe cycle. (iii) Calculate the specific heat provided to the boiler, the specificwork extracted from the power station and the mass flow rate ofthe steam circulating in the cycle, then, determine the thermal efficiency of the cycle.
Q1. Sketch T-s diagram for Rankine cycle with clear label for the following condition: Condensate pressure = 100 kPa • Boiler pressure = 3 MPa • Inlet temperature to the turbine = 350°C Determine thermal efficiency of the cycle. ANSWER
Describe the ideal process for an adiabatic turbine.