Problem 1 An electrical power supply system is constructed with a DC machine with the following information: Power is ID kW with IDO V · The armature and field resistances are 0.8 Q, 0.4Q and 180 Q • Calculate the power that can be developed by the designed system with the following conditions: Condition 1: 180 Q is in parallel with (0.8 +0.4) Q.

Problem 1 An electrical power supply system is constructed with a DC machine with the following information: Power is ID kW with IDO V · The armature and field resistances are 0.8 Q, 0.4Q and 180 Q • Calculate the power that can be developed by the designed system with the following conditions: Condition 1: 180 Q is in parallel with (0.8 +0.4) Q.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

Iron losses in a DC machine are independent of variations in ) load voltage speed O All of these
1-13 Describe Kirchhoff's Voltage Law. Explain how it relates to the principle of the conservation of energy.
A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of the Thyristor (5 µA) and frequency (50 Hz). Find the rate of voltage changing with time and snubber circuit power losses?
I need help understand on the question of how does the vertical shift compareto the dc level of battery.
A 255 V, DC lathe machine, (not a 2 pole machine) has armature resistance and series resistance are 0.150 and 1702 respectively. The motor has 25mWb flux per pole. The ratio of pole to parallel paths is unity. The product of this ratio and number of turns in armature section is 1000. When it runs light, it has a speed of 1200 rpm. If it runs at maximum load, it takes a current of 70A. (1) Which machine is this one, shunt or series ? Is machine lap wound or wave wound? (3) Calculate the no load back EMF. (4) Calculate the no load armature current. (5) Calculate the no load shunt current. (6) Calculate the current drawn by the machine. Calculate the variable losses on load. (8) Calculate the armature power when it runs light. (9) Calculate the stray losses when it runs light. (10) Calculate the full load armature current. (11) (12) (13) Calculate the full load back EMF. Calculate the Variable losses on maximum possible load. Calculate the armature power on maximum load. (14) Calculate…
Electromagnetism 1. A coil has 480 turns and flux in it changes from 0.24 m Wb to 1.2 m Wb in 0.24 second. Calculate the voltage induced in the coil. instructions: Solve in step by step manner as possible for future referencesPlease illustrate properly and draw the solving Make sure to write it in a clean sheet of paper to review
Solve 2,3 only.Note the load resistance is 10 ohm and frequency 60 Hz
b) A certain winding made up of copper has a resistance of 100 Q at room temperature. If resistance temperature coefficient of copper at 0 C° is 0.00428/C°, calculate the winding resistance if temperature is increased to 45 C°. Assume room temperature as 25 C°.
20. The resistance R and a 2 μF capacitor are connected in series across 200-V dc supply. Across the capacitor is a neon lamp that strikes at 120 volts. Calculate the value of R to make the lamp strikes 5 seconds after the switch has been closed. A. 4.89 kΩ B. 4.89 MΩ C. 2.73 MΩ D. 2.94 MΩ
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
An ac resistance is higher than a dc resistance. True False
Iron losses in a DC machines are independent of variations in: * voltage and current speed and current current voltage speed load speed and voltage