Problem 1 A Design a 4-bit combinational circuit 2's complementer. Determine the Boolean expression of the output signals W and X in product-of-sums (POS) form. Only the required output signals should be shown or your answer sheet. NOTE: Justify your answer by showing the circuit's truth table. Your answer should conform to the correct entries in your truth table. B Inputs C D minterm (m) W Outputs X Y Z NOTES Required format of the truth table in Problem 1. Input entries should be listed in ascending order. No other information should be shown on the table except those indicated above. Show complete input and output entries on map. Show complete table and map grid lines. Appropriately label all groups on map.

Problem 1 A Design a 4-bit combinational circuit 2's complementer. Determine the Boolean expression of the output signals W and X in product-of-sums (POS) form. Only the required output signals should be shown or your answer sheet. NOTE: Justify your answer by showing the circuit's truth table. Your answer should conform to the correct entries in your truth table. B Inputs C D minterm (m) W Outputs X Y Z NOTES Required format of the truth table in Problem 1. Input entries should be listed in ascending order. No other information should be shown on the table except those indicated above. Show complete input and output entries on map. Show complete table and map grid lines. Appropriately label all groups on map.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Q2 Implement the function F(x1, x2, x3, x4) = II M(0,1,2,3,8,9,12,13) using 2 input look-up tables ( LUT- shown in figure 2 below ). Give the truth table implemented in each LUT. You do not need to show the wires in the FPGA, you need to show how the LUTS are connected . input 1 0/1 0/1 output 0/1 0/1 input 2 Fig 2 Circuit for a two-input LUT
7. Write the simplified (minimized) expression for the Boolean function defined by the following Karnaugh Map (KMap) in Sum of Product (SOP) form. WX yz 00 01 11 10 00 0 0 1 1 01 1 1 1 1 11 0 1 0 0 10 1 1 0 1
6. For the truth table below, write its Boolean expression in canonical SOP form, then draw the circuit. Using the Boolean algebra rules, simplify the circuit (do NOT use a K-map) to a simpler SOP form and draw that SOP circuit. X 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Implement the given Boolean function with multiplexer. F (A, B, C, D) =E (m (1,3,5,7,8,10,12,13,14), d (4,6,15))
Please find the simplest "sum-of-products" expression of f(A, B, C, D) = 2 (1,4,6,8,11,13,14) + o/(7,12) using Karnaugh map, draw the Circuit using NOR gates only, and write the cod as a VHDL module.
A combinational circuit is described by this Boolean Expression: F(A,B,C,D) = 2m(0,2,4,8,9) i) Minimise the Boolean Expression given above using a Karnaugh map. ii) Given Don't Care conditions d = Em (10,11,12), use a separate Karnaugh map to demonstrate how you would further simplify the expression in part i). iii) Use Switching Algebra to show how you would implement the function obtained in part ii) by using NAND gates only. Provide a circuit diagram in your answer. Show all your working.
Implement the following function with a8-to-1-line Multiplexer with threeselection lines? Draw the truth table and the corresponding block diagram for the MUX?F(A, B, C, D) = Σm ( 1, 3, 4, 11, 12, 13,14,15 )
1. Find the output expression for X before simplification. 2. Find the minimum expression using K map. 3. Use logisim to draw the logic circuit using only NOR gates Q2 For the truth table below, do the following: A 0 0 0 0 0 0 0 0 1 1 1 1 1 B C D X 0 0 0 1 0 0 1 1 0 1 0 0 0 1 0 1 0 1 1 1 0 1 0 1 1 0 0 1 0 1 1 1 0 0 1 1 1 0 0 0 0 0 11 1 1 1 1 0 1 0 0 0 0 1 0 0 0 1 1 0
Id = 1931487642 You need to display your IDs first 7 digits using one seven segment display. This is an individual project & you need to work at logisim. You need to design a combinational circuit where you will provide manual input. For each of your inputs, your IDs one digit will be shown. After solving the K-map, if your IDs 7th digit is an Even Number then you need to implement every boolean function using NAND gate and if your IDs 7th digit is Odd Number then you need to implement every boolean function using NOR gate. Simulate the circuit and upload the ".circ" file, no screenshot is allowed.
Q10. Please simplify the following functions into the simplest SOP expression using the karnaugh map (1) Y = AB + AC + BC + CD (2)_Y(A,B,C,D)= Σm(0,1,2,5,8,9,10,12,14)
Simplify the following boolean expressions, using k-maps ABCD+ACD+BCD+ABCD+BCD wyz+wx+wxz
Create an implementation using 2-input NAND gates only for the following equation. You may use inverter symbols internally and/or inversion symbols ( ) on the inputs as has been done in the example with the understanding that these would be replaced with 2-input NAND gates with inputs tied together. Be sure to minimize your SOP equations before conversion the NAND-only. f(a, b, c, d) = c'd + c(b' + d)