Power in a dc circuit is calculated as the product of current and voltage if the value of current and voltage are given by 6.3A and 110.2V and the uncertainties involved in their measurement being 0.06A and 0.1V .Calculate the power dissipated by the loads and the uncertainty involved in measurement.

Q: Discuss about the performance characteristics of wind turbine

A: Introduction - Wind turbines use aerodynamic force by the propeller blades to convert wind energy…

Q: b) The thermal noise power (Pn) available from a resistor (R) is equal to -140 dBm. If the thermal…

A:

Q: Discuss the advantage of electric vehicles

A: For the above given question we need to list advantages of the electric vehicles.

Q: Give a sample problem regarding this topic and its formula: Maximum Power Developed by a Motor v2…

A:

Q: Identify a true statement about time domain. -It refers to displaying or expressing a signal as a…

A:

Q: (d) Define the numèrical aperture of step index fiber. . (e). What is the need of cladding?

A: D) Numerical aperture of index fiber : Numerical Aperture of step index fiber is the ability of step…

Q: What is Ohms law? Explain with examples

A: Define Ohm's Law

Q: Discuss advantages of per units representation

A: Advantages of per unit representation

Q: values for the same component. This causes different signed power therefore we cannot state whether…

A: Simple solution regarding this chaos: If the current is discharging from any device that means if…

Q: Four industrial centers are located at the corners of a square of 31300 m side. The loads are 460000…

A: Substation supplies power to industrial loads To obtain better power transfer efficiency from…

Q: What is Repeated Measures?

A: There are many measurements of every subject in repeated designs and all subjects are distributed to…

Q: Answer the following questions 1- Explain how to select the slope of the collector, give an example?

A: As per the honour code I will only answer the first question. Kindly repost the other questions…

Q: 6. BJT is more linear than FET. Why? Explain

A: A BJT has constant gain in the active region so the graph obtained in this region is a straight line…

Q: If VTh is 6020° V, what is l, ?

A: The solution can be achieved as follows.

Q: 9. If DS1 shorted, what is the voltage across L-N if a multi-tester set at 600V AC range?

A: Givewn that DS1 is shorted  Now draw the modified circuiut

Q: After the determination of the currents references, can we connect the ammeter terminals in any way…

A: Because Current is a vector, it will also have a direction. Positive and negative terminals will be…

Q: A highly inductive load, such that load current can be assumed constant, is to be supplied from a…

A: Here, we have to calculate the output voltage produced by the fully-controlled and a half-controlled…

Q: which the voltage regulation is maximum and the value of this regulation.

A:

Q: Draw the relationship between excitation current and short circuit, and Please explain

A: According to guidelines we need to solve only the first question. According to the question we have…

Q: Derating means that the maximum power dissipation is reduced when temperature is reduced according…

A: we need to find that the given statement is true or false. statement:Derating means that the maximum…

Q: Please write short introduction about AC Circuits - Series Circuits

A: An a.c circuit differs from a d.c circuit in many respects. First, in a d.c circuit we consider…

Q: What are the benefits of using mechanical Processes of integrated circuts.

A: A single-unit electronic assembly consisting of miniaturized active and passive components (such as…

Q: Introduction: write about Voltage, Current and Electrical Impedance

A: Voltage or potential difference is the difference in electric potential between two points, which…

Q: Discuss uncertainty relating to voltage, DC-resistance measurements, and AC-impedance measurements.

A:

Q: (a) Briefly explain what is the per-unit system. (b) A resistance of 600 is selected as the base…

A: Disclaimer:  Since you have asked multipart questions, we will solve the first three subpart for…

Q: Q5] What is a parametric representation of a curve? What is its advantage?

A: Parametric representation of curve: In an (x,y) plane, the x and y coordinates of a curve can be…

Q: An audio power amplifier delivers an 80-volt peak 35 Hz sine to a subwoofer. If the subwoofer…

A: Given data, Peak voltage Vp=80 V Frequency f = 30 Hz Impedance Z=4∠-300

Q: 1. Using the circuit of Figure 2.1 with RI -1 k, R2 =2,2 k, R3 the theoretical current and record it…

A: Note: Here we have solved only theory part of the questions. For remaining parts, actual experiment…

Q: If the same meter movement from no.1 is to be used in an Ayrton shunt arrangement, find the required…

A:

Q: please write introduction about Analysis of simple AC Circuits using MATLAB

A: MATLAB programming and simulink are used to analyze the network or circuit in theoritically before…

Q: Develop block diagram of hybrid electric vehicles

A: Hybrid Electric Vehicle (HEV) A hybrid electric vehicle (HEV) is a kind of vehicle that integrates…

Q: (a)Using the current sheet concept derive the peak value of mmf of a machine in terms of uniform…

A: Current sheet concept: It was seen over that a distributed winding brings about an MMF wave in…

Q: Write examples of random and deterministic signals in physiological systems.

A:

Q: 7. Describe the direct connection, series and parallel methods of measurements using Q-meters? Why…

A: Q-meter is used to measure quality factor of a coil Q. Also measures Resistance R, inductance L and…

Q: Is the relationship between the change in Vgs and the resulting change in In linear or non- linear?…

A: The relation between the gate-source voltage and the diode current can be given by the Shockley’s…

Q: Explain the difference between AC and DC and give examples

A:

Q: a. Description of lamp-ballast system

A: Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: explain flexibility in FACTS and write the ways to achieve it. despite many advantages of dc…

A: FACTS or flexible alternating currents transmission system is a system of transmitting electrical…

Q: What do you mean by Ferranti effect? How does it affect voltage regulation? Which one among…

A: 1) Ferranti effect :- The transmission line under No load or lightly loaded condition is subjected…

Q: please write introduction about AC Circuits and Parallel Circuits

A: Ac circuits Generally, series A.C circuits are of 3 types-      R-L series A.C circuit  R-C series…

Q: What does a "matched load" mean?

A: According to guidelines we need to solve only the first question. According to the question we have…

Q: These question from electronics two course

A:

Q: what are Model electrical and mechanical systems in state space ? Explain it in a simple way and…

A: State space model- State space model is inferring for the state variables given the observations at…

Q: (A) The circuit shown in figure below has a Ves(oft) = -4V. Assume that you increase the supply…

A: A) The given circuit is, By increasing a supply voltage the drain current ID also increases from…