2) An idealized free-body diagram of a door handle is shown below. To simplify, member X-Y is only experiencing torque while member X-Z is only experiencing flexure. What should be the minimum thickness of the handle of member X-Z if the maximum allowable flexure is 3MPa? What is the maximum torsional shearing stress experienced by member X-Y? What is the angle of twist? *G=83MPa.

2) An idealized free-body diagram of a door handle is shown below. To simplify, member X-Y is only experiencing torque while member X-Z is only experiencing flexure. What should be the minimum thickness of the handle of member X-Z if the maximum allowable flexure is 3MPa? What is the maximum torsional shearing stress experienced by member X-Y? What is the angle of twist? *G=83MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P 130 mm 25 mm 25 mm P P 3. Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
a) Two bars of different size form a pin-connected frame that supports a Load 'P' at point A as shown in the Fig. 3. What safe load P (kN) can be applied if the allowable stress of 120 MPa is not to be exceeded? Assume buckling has been prevented. Allowable stress is based on a factor of safety of 2.0. Cross sectional area of the rods AB and AC are given in the adjacent table as per last digit of Roll number. What is the failure load? Last digit of Area of AB | Area of AC Roll No. 1, 2, 4 & 7 200 mm 230 mm“ 3, 6 & 8 160 mm- 190 mm² 5, 9 & 0 180 mm 210 mm 2400 1600 Fig. 3 b) Two square bars are of equal length but have different size as shown in Fig. 4. Compare the maximum stress in the two bars if they are to receive the same input of energy from axial load. Given, m = (2 + last digit of your roll number). 2a 5.x m.x Fig. 4 last digit of roll=1
A cantilevered structural member is fabricated with the cross section shown below and is eccentrically loaded with F. - 26- F 2t F tt Use G = 77.2 GPa. If I = 4 m, t = 3 mm, b = 80 mm, and F = 112 kN, %3D Determine the maximum shear stress due to torsion. Select the correct response: 133.333 MPa 215.278 MPa 168.056 MPa 155.556 MPa
The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional view by nailing wooden parts with cross-sections of 50 mm x c = 220 mm and 25 mm x d = 260 mm. How large can the value of the load P be when the distance between the nails in the longitudinal direction of the beam is 100 mm, the cross-sectional area of the nail is 9 mm2 and their permissible shear stress is 110MPa? Then calculate the maximum stresses and shear stresses of the beam at that load when the distance between the articulated supports is L = 1.9 m and the length of the beam projections a = 1.3 m. Permissible shear force of one nail? kN Static torque of the cutting surface? mm^3 Maximum torque change in cantilever? kNm Cutting force of the projection? kN Magnitude of force P? kN Calculated with the obtained force P maximum normal stress? MPa shear stress maximum? MPa
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
A stepped shaft made of steel is fixed at one end and 1.5 kN-m torque is applied at other end. What additional torque that can be applied at point B if the maximum shear stress is not to be exceeded 105 MPa and the total angle of twist should not exceeds 3°. The modulus of elasticity of steel may be taken as 200 GPa and Poisson's ratio as 0.3. 750 B 600 3-11- 70 90
AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume P = 129 kN, w = 22 kN/m a = 2.8 m, and b = 2.2 m. Determine the magnitude and location of the maximum bending stress in the beam. A omax = x = a i i P B a Pin C b MPa m W O D a E
A tension member in a roof truss is composed of two ASTM A36 structural steel angles that together have a net cross-sectional area of 5.66 in?. Compute the allowable total load if the allowable tensile stress is 25,000 psi. O a. 189.64 kips O b. 141.50 kips O. 137.16 kips O d. 220.25 kips
Activity 3 Questions WHAT'S YOUR SCORE? Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 5º. Use G = 80 GPa for steel. (Note: Two values of P are to be compared here). 300 mm 500 mm
1. The bar ABCD consists of 3 cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment in psi unit. Indicate if T or C.Calculate the total axial deformation in Problem #1 if Es = 29 x 10 6 psi . Indicate if the bar elongates or contracts.
A T section of a beam is fabricated from 2 - 12 mm x 150 mm steelplates and joined by welding as shown in Figure ST - 904. It carries a live loadof 6.5 kN/m extending half of its span. Neglect the weight 1. Compute the maximum compressive stress. ( bending stress incompression )2. Compute the maximum tensile stress. ( bending stress intension )3. Compute the maximum shear stress. 4. Compute the shear stress between the junction of web and flange. 5. Compute the maximum deflection. EI is constant.
2. Two rods connected as shown carry a vertical load of 20 kN. Rod AB is a steel rod with E = 2 X10 MPa while rod BC is made up of aluminum whose E = 7x10¹MPa. The rods are rigidly pinned at A and C and have cross-sectional areas equal to 400 mm². If a is changed from 30° to 45°, compute: (a) stresses in each rod. Specify if tensile or compressive stress (b) deformation of each rod. Specify if elongation or shortening. B P=20 KN L=3m α=30° 70=30° L=2m