Please describe what method/application you are using in each step. (so I can understand it) (and that the result is good, of course).

Q: •1. Based on the differences stated between a Microprocessor and Microcontroller, Give two examples…

A: Microprocessor and microcontrollers are used for data processing. Logic and control are used for…

Q: Q5(a) Explain the Hebbian's Law. (b) Depict a diagram of a Hebbian learning in a neural network.

A:

Q: Suppose that we have an unusual type of FET for which iD=3vGS3+0.1vDS Here, iD is in mA, vGS is in…

A: Given Information: Formula and Concept: The trans-conductance is equal to the partial derivative…

Q: Explain the successive approximation

A:

Q: A- what information can be obtained from the open-circuit test.

A:

Q: Are the following statements correct or wrong? Justify your answer. (a) GTO requires very high…

A: A) statement is correct.. Because GTO have turn off gain is low.. B) statement is wrong.. Because…

Q: As a design engineer in an electronic instrumentation manufacturing company, you are required to…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: The resolution of the ADC unit with the reference voltage value of 3V is set to 8 bits. If the…

A:

Q: Specify the configuration of the circuit

A: Given :  Brief description: Transistor is a 3 terminal device which is used in electronic devices…

Q: 4. In a temperature measurement system, the gains are K, = 20+1µV, K, = 500 + 10V/V, and K, = 100+5…

A:

Q: The value of Vs is

A: Draw the circuit under dc conditions, capacitor acts as open circuits.

Q: Q15. A circuit comprising a DC voltage source, three resistors, and two LEDS is shown, where R=1 2,…

A: Given, R1=2 ΩVF!=2.2 VVF2=2.8 VPL1=1.15PL2

Q: Design an electronic system that represents some scenario created by you? (simple one that contains…

A:

Q: Leave an image of the exercise in Spanish, so that it is better understood. In the other image, is…

A:

Q: 1-An ADC with word length of 24 bits. If the input analogue signal range is 3.7 V, what is the…

A:

Q: Show the difference between the Accuracy, Precision, and Resolution with definitions and examples.

A: Accuracy: It is the closeness of the result/output of the measurement to the actual value Precision:…

Q: (c) Name the components labelled for the encoder shown in Figure Q3(c). (d) Amp Sig 1 Amp Sig 2…

A: a) Light Emitting Diode (LED) / Light Source b) Condenser lens c) Aperture

Q: Briefly explain the behavior of the circuit below.

A: Given: Consider the following circuit: To find: Briefly explain the behavior of the given circuit.

Q: a) What is the name of the circuit given below? b) Calculate DC bias values for the circuit given…

A: The circuit is a potential divider bias, also known as voltage divider bias, used for the dc biasing…

Q: Discuss two ADCs with circuit diagram and proper equations. List their pros and cons.

A: Flash type ADC The operation of Flash ADC is the fastest compared to all other ADCs. Hence, Flash…

Q: What differentiate rethinking model from refine model?

A: (d) Managers have varying proclivities for participatory decision making (PPDM), thus the…

Q: 2. (a) An electrocardiogram (ECG) is a recording of the electrical activity of the heart. When…

A:

Q: c) Electronics engineering defines a broad field that encompasses many subfields including those…

A: To interpret the cardinal role of electronics engineer

Q: 1. Explain the difference between digital and analogue electronics devices, and then Explain the…

A: Digital devices:- In digital devices signals are discrete in time and values. Signals are…

Q: compute the voltage labeled ??

A: It is given that:

Q: . Write the difference between the MOSFET and IGBT?

A: IGBT MOSFET Stands for Insulated Gate Bipolar Transistor Stands for Metal Oxide Semiconductor…

Q: Derive mathematically the relationship between α and β?  Note( The β is twice the α)

A: A transistor has three terminal base terminal, collector terminal and emitter terminal and current…

Q: A printed circuit board (PCB) machine installs integrated circuits onto a board. Beforestarting to…

A: It is given that: 1. Integrated circuits are mounted on a board using a printed circuit board (PCB)…

Q: What would 11001010 be in octal and hexadecimal? Thank you.

A:

Q: Generate the state table and diagram of the circuit

A: Given the sequential circuit: We need to generate the state table and state diagram of the circuit.

Q: One application for electronics that has gained a lot of attention over the past several years is in…

A: As seen in the diagram, there is resistance between E1 and E2 and is given by the equivalent…

Q: 3. For the question above, find the current through the inductor

A: Since you have asked answers for only Question number 3 . Below is the answer.

Q: I If a microprocessor can perform 4 million. instructions per second, how many nano seconds are…

A:

Q: Suppose you are developing the simulation model of a communication system where the incoming calls…

A: We need to solve: Suppose you are developing the simulation model of a communication system where…

Q: Explain RTD with necessary diagram and equations.

A: A Resistance Temperature Detector (also known as a Resistance Thermometer or RTD) is an electronic…

Q: (d) Determine IC and VCE for the network of Figure (b). (e) Change β to 180 and determine the new…

A: As per the policy, attempting first three subparts of the question (d)Base current can be calculated…

Q: In your own opinion, what do you think is the importance of having this Basic Measurement Theory?…

A: The real world demands the analysis and design of complex systems. It is possible with the clear…

Q: With the tiny, distributed sensor application in mind, list and briefly explain the six TinyOS…

A: A tiny OS provides the medium and an interface between yours program which contains some application…

Q: Q2/Obtain state table and state diagram, also what is the type of the system moore or mealy? A CIK

A: The state table for the given diagram is given by:

Q: 2. Describe what you understand by overcurrents and indicate the protection devices that can be used…

A: Overcurrent is the condition in the electrical circuit when there is increase in the load current.…

Q: Explain any two signal processing in the 3 measurement system with best diagrams

A: Measurement system :   Any of the systems employed in the process of integrating numbers with…

Q: Explain from their production to their use to produce, what are the positive and negative effects…

A: Advantages Operation performing time is low. Maintenance is easy and also the troubleshooting Size,…

Q: A complex CMOS (Complementary metal oxide semiconductors) network is given in Figure-2. Network…

A: FETs are voltage-controlled switches. The voltage at the gate terminal decides if the switch is…

Q: Explain the operation of the circuit below. Include a description of its output waveform, including…

A: The given circuit diagram is shown below:

Q: 1. How many resistors and switches would be required to implement a 6-bit resistor-string DAC?

A: Number of resistors = 64 Number of switches = 63 Go through below for the explanation

Q: Explain in detail the essential things that happen to the modulating signal before transmission.…

A:

Q: Discuss the problems with Concentrated Solar Power (CSP) Systems.

A: Following are the problems associated with concentrated solar power (CSP) systems. Water…

Q: V DD R1 Rp V. M1 out Cs R2 ECG Rs Vss = 0 V Figure 1

A: We need to draw small signal for given circuit.

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.