P12.20 (WP The cylinder in Figure P12.20 consists of spirally wrapped steel plates that are welded at the seams. The cylinder has an outside diameter of 280 mm and a wall thickness of 7 mm. The cylinder is subjected to axial loads P = 90 kN. For a seam angle ß = 35°, determine P (a) the normal stress perpendicular to the weld seams. (b) the shear stress parallel to the weld seams. FIGURE P12.20

P12.20 (WP The cylinder in Figure P12.20 consists of spirally wrapped steel plates that are welded at the seams. The cylinder has an outside diameter of 280 mm and a wall thickness of 7 mm. The cylinder is subjected to axial loads P = 90 kN. For a seam angle ß = 35°, determine P (a) the normal stress perpendicular to the weld seams. (b) the shear stress parallel to the weld seams. FIGURE P12.20

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

10. Two tie bars are connected together by 0.5cm fillet welds around the end of 1 bar and the inside of a slot machined in the same bar. Estimate the strength of the connection in tension if the shearing stress in the welds is limited to 75MPa. 450m 10cm 8cm
Question No. 11: (a) Illustrate flatness, straightness and circularity with symbol. (b) A circular shaft, 80 mm in diameter is welded to support by means of a circumferential fillet weld. It is subjected to a torsion moment of 3000 N-m. Determine the size of weld, if the maximum shear stress in the weld is not to exceed 70 N/mm2 . (c) Analyze different stresses during design of screw and nut
Fig. 8.76 6 A welded joint, as shown in Fig. 8.77, is subjected to an eccentric load of 2500 N. Find the size of the weld, if the maximum shear stress in the weld is not to exceed SO N/mm?. (6.4 mm) 2500 N -150 田 50
11.16 Two 20-mm steel plates are butt-welded together. Both the plate and the welding electrode materials correspond to strength properties of Su = 500 MPa and S, = 400 MPa. The imposed loading fluctuates rapidly between -20 and +60 kN. Estimate the length of weld required in order to provide a safety factor of 2.5: (a) If the weld reinforcement is not removed. (b) If the excess weld material is carefully ground off to provide smooth, continu- ous surfaces.
1. A butt weld is set on the cross section of an I-shaped beam. There are bending moment M and shear force V at the splicing position, where M=1120 kN•m and V= 374 kN. The beam is made of Q355b steel and semi-automatic weld is used with welding rod E50. The design value of the weld tensile strength f," is 260 N/mm². Please check whether the strength of the butt weld is safe by calculation. 280 M M 0001
7) For double side parallel fillet weld subjected to an external force 100 kN. The weld has throat thickness of 5 mm and the measured shear stress is found to be 100 MPa. From the above given information find out the length of the welded joint desigN? O 100 mm 50 mm 25 mm 10 mm
T3.2.1 The bracket shown below is to support a total load (equally divided between the two sides) of 60 kN. Using E60 series welding rod and safety factor 3.0, what size weld should be specified? [Ans. 7 mm] 60 KN 100 mm 75 mm 55 mm) Note: Each plate has two 75 mm welds and one 100 mm weld.
Two plates, 25 mm thick, are welded together by means of trans verse-fillet welds. The ultimate tensile strength of a weld metal is 415 MPa. The surface finish factor of the weld surface is 0.5, and the size factor is 0.85. The reliability is 90%. Determine the length of the weld if the factor of safety is 2. The transverse force on the welds is 100 kN, which is completely reversed under fatigue loading. Take: A=10mm 25 Toe Р.
8. Design the length of weld (L) in the connection below to develop the full tensile capacity of the plate. Use E70 electrodes and 1/4" side fillet welds. The material is ASTM A36 Steel and the allowable axial tensile stress is 22,000 psi. (show all your work) "L" PL 1/2" PL 3/8" x 6" P
Q2: Two plates, 25 mm thick, are welded together by means of trans verse-fillet welds. The ultimate tensile strength of a weld metal is 415 MPa. The surface finish factor of the weld surface is 0.5, and the size factor is 0.85. The reliability is 90%. Determine the length of the weld if the factor of safety is 2. The transverse force on the welds is 100 kN, which is completely reversed under fatigue loading. Take: A=10mm 25 A Toe
Ex Welding.pdf → The Figure shows a 0.75-in-thick AISI 1020 HR steel bar subjected to a load of (F = 1.4 kip) and welded to a vertical support using a 7010 electrode. Estimate the shear stress for the weld. For the AISI 1020 HR steel bar, S, = 30 kpsi, Su= 55 kpsi (from the table) From the pattern of weld shown below, b= d = 2 in (welding table) bd2 * = b/2 ý = d/2 A = 1.414hd Then, A = 1.414hd = 1.414(5/16)(2) = 0.884 in? I= bd/2 = 2(4)/2 = 4 in 1= 0.707hl, = 0.707(5/16)(4) = 0.884 in Primary shear: F t%3D A 1.4 = 1.584 kpsi 0.884 Secondary shear: Mr " = 1.4(7)(1) = 11.086 kpsi 0.884 Then, the shear stress is 1=Vr2 + t"2 = V2.509 + 122.9 = 11.2 kpsi . Ans II
For the following configurations shown in figure below, determine the ratio of the maximum shear stress acting on the tube before and after the seam is welded. Then determine the ratio of the maximum angle of twist. Use the inner diameter to be 60 mm and the outer diameter to be 80 mm. Weld Narrow. slit