Learning Goal: To determine the effects of certain geometric shapes, namely fillets and circular cutouts, on the stress distributions inside a rigid body and to determine the maximum applicable axial force in the same rigid body while considering these stress concentrations. The member shown below is made of steel (oallow = 145 MPa ) that is 80 mm thick. The member is subjected to an axial force P that is applied at both ends. Let r = 10 mm , w = 120 mm , h = 40 mm , and d = 25 mm

Learning Goal: To determine the effects of certain geometric shapes, namely fillets and circular cutouts, on the stress distributions inside a rigid body and to determine the maximum applicable axial force in the same rigid body while considering these stress concentrations. The member shown below is made of steel (oallow = 145 MPa ) that is 80 mm thick. The member is subjected to an axial force P that is applied at both ends. Let r = 10 mm , w = 120 mm , h = 40 mm , and d = 25 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If the Poisson’ Ration is 0.30 and the modulus of elasticity is 29xksi, determine the deformations at each direction. Also, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
A hollow circular pole 3 m high is fixed at the base. It is 6mm thick and its outside diameter is 300mm. The pole is subjected to a torque and a lateral force at the free end. Given: Torque, T = 25 kN-m Lateral Force, N = 3 kN Shear Modulus of Elasticity = 78 GPa Allowable Shear Stress = 60 MPa 1. What is the maximum shear stress (MPa) at the outside surface of the pole due to the torque, T? 2. What is the angle of twist (degree) due to the torque? 3. Find the maximum flexural stress (MPa) at the base of the pole due to the lateral force.
3. A cylindrical rod is fixed between two walls. The rod is composed of two materials. Section AC is made of one material (GAC = 2G) while section CD is made of a different material (GcD = G). A torque, T, is applied at point B, as shown below. Jac = JcD = J = 2 in. GẠC = 2G = 20 x 10ʻ psi T= 300 kip in. GCD = G = 10 × 106 psi A D 2L Determine the reactions at the wall, Ta, and Tp. Specify the direction for each. (Note: this is an example of a no calculator problem.) Ans: TA = 250 kip in ( Tp=50 kip in ( T Fixed Fixed to wall to wall
The surface of a helicopter blade is subjected to plane stress with normal stresses ox and oy and shear stress Txy, as shown in Figure Q1(b). From the analysis, it shows that at counterclockwise angle e = 32° from the x axis, the normal stress is 37 MPa (tension), and at counterclockwise angle e = 48°, the normal stress is 12 MPa (compression). Determine oy and Txy by using the stress transformation equations Txy ↑0, = 110 MPa
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
Learning Goal: To use Hooke's law to determine the value of an axial load applied to a rectangular shape and to determine its lateral expansion. The element shown below is subjected to the axial compressive force P, which causes the shape to contract longitudinally in the direction a distance of 8 = 0.720 mm. Let h = 144.5 mm, w = 88.50 mm, and L = 298.0 mm. Assume the element is made from steel that has a modulus of elasticity of E= 200 GPa and a value of Poisson's ratio of v=0.32. ♥ Part A Value of the axial load Determine the value of the axial load P. Express your answer to four significant figures and include the appropriate units. View Available Hint(s) P = Submit P μÀ Value Units ? Part B Lateral expansion in the y direction Determine the lateral expansion in the y direction due to the axial load. Express your answer to four significant figures and include the appropriate units. View Available Hint(s) dy = Submit d₂ = Value Part C - Lateral expansion in the z direction μA Submit…
Exercise: 1. Determine the stress in each section of the bar shown in the below figure when subjected to a tensile load of 20 kN. The central section is 30 mm square cross section; the other portions are of circular section, their diameters being indicated. What will be the total extension of the bar? For the bar material 210 GN/m² t100 250 400 20 kN 20 kN 15 20 30 2. Calculate the spring constant of a spring that needs a force of 3N to be compressed from 40cm to 35cm
A very thick structure is subjected to certain traction boundary conditions on its surface. The cross-section and the applied load do not vary with the z-coordinate. The following stress function is proposed for this problem: -y p(x,y) = Sin (x) (A x²e + B e") (i) use the biharmonic equation to find restrictions, if any, on values of A and B (ii) calculate all stress components (iii) calculate all strain components in terms of A, B, and C as well as the Young modulus and Poisson's ratio E and y, respectively. (iv) check that the equilibrium equations are satisfied (v) determine the traction boundary conditions at x =± a and y=+b
2-A wheel of diameter d and width w carrying a load F rolls on a flat rail. Estimate the maximum contact pressure for these materials. Por vedit -3D d 5 in 150 mm 3 in W 2 in 40 mm 1.25 in F 600 lbf 2 kN 250 lbf Wheel Material Steel Steel Cast iron Rail Material Steel Cast iron Cast iron.
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 48512-Nload, using the following data: length of steel = 1.42 m, length of bronze = 2.36 m Area of steel = 639 mm, Area of bronze = 319 mm Modulus of elasticity of steel = 180 Gpa, Modulus of elasticity of bronze = 81 Gpa x = 0.58 m, y = 1.13 m, and z = 0.72 m. Round off the final answer to two decimal places.
The horizontal member ABC supports a point load of P (KN) and is pin-supported at B and C. The member (link) DB is a structural steel that pin- supported at D with the given dimensions (All the pins will have 5mm diameter). a) If the force P=100 kN find the max shear stress in the pins. b) Find the max force P such that the member BD will remain elastic c) Find the max displacement of point A such #remain elastic
A helical spring used in an automobile suspension is having a wire diameter of 6mm and an outside diameter of 86mm. The spring has 14 active coils. If the permissible shear stress of the spring material is 345 N/mm2 and the Modulus of rigidity is 82 kN/mm2. a) Calculate the axial load in N and the deflection of the spring in mm, considering the effect of curvature. b) Calculate the value of axial load in N neglecting the effect of curvature.