If the impedance is given by Z = (8 + j6) ohms, what will be its conductance? mho Tomho ✓ 0.08 mho 0.06 mho
Q: Question: 2 Tp.u(s) T₁₂ (8) = 3²7 +35 This process is controlled by a P controller with gain Kc = 3.…
A: The given process transfer function is Tpus=2s2+3s. Gain of the P-controller is Kc=3. Sensor and…
Q: Use the residue method of (3-10) to find the starred transform of the following functions. 1 10 (a)…
A: Given set of problem Asked to find starred transform using residue method
Q: Design a 18 person voter system using 4 bit parallel adder(s) only. Use a minimum number of…
A: Given components: 4-bit parallel adders To design: An 18-person voter system using a minimum…
Q: 16V +1 www 4Ω 8H|i₁ The circuit above is in DC steady state. What is the value of it in amps? 201
A: Given data: A circuit is shown below. The circuit is in DC steady state. Find iL current in amps.
Q: A symmetrical fault occurs on a power system. The percentage reactance of the system on 2500 base…
A: Given: A symmetrical fault occurs in a power system with, Base kVA = 2500 kVA. Percentage reactance,…
Q: List the elements included in the total input resistance of a common-collector amplifier. What is…
A: Given: List the elements included in the total input resistance of a common-collector amplifier and…
Q: find it at t20 s. 12ucts Y. 1 kr. ikn. HEM 1ª MF 1kr zuc-t, mA. (S. 1 ke. PUSHE
A:
Q: No start-up costs; no minimum up- or downtime constraints. a. Solve for the unit commitment by…
A: In unit commitment and economic dispatch, those units will be operated first which are economical…
Q: CLK f=12KHz 6KHz 4KHz 2KHz 7493 4CKA QA OCKB QB R01 QC R02 QD In reference to the circuit above, the…
A:
Q: What is the current through the resistor in the following circuit, if AV=20 V and R= 100 S2? A. 20…
A: Given circuit, where, Voltage, ∆V=20 V Resistance, R=100 Ω
Q: 1A (A ww 3Ω + 8F VC - The circuit above is in DC steady state. What is the value of v, in volts? 5Ω
A:
Q: A d.c. series generator supplies the load of 5 kW at 250 volts. The armature resistance and series…
A: Solution: Given data ; d.c. series generator ; output =5 KW , V =250 V, armature resistance Ra=1 Ω,…
Q: Find the F.T. of the following Signals using differentiation prop. №. 2 2 +t Ans F(w) = 4(sinc(w) -…
A: A function's differentiation in the time domain is equal to multiplying its Fourier transform by a…
Q: Q3) Evaluate both sides of divergence theorem if D-3pZ² ap+3Z a and a cylinder: p=2m, (0≤Z≤5) m.…
A: The divergence operator is used by the Gauss divergence theorem to transform surface to volume…
Q: 750kW alternators are operated in parallel. P₁ = 750kW, P₂ = 750kW Speed regulation of one machine…
A: Dear student you have not posted question and you have doubt in solution, so I’m solving your doubt…
Q: Draw logic diagrams of the circuits that implement the original and simplified expressions in…
A: Logic diagram:- It is a representation of Boolean arithmetic expression which consists of logic…
Q: Determine whether the following Boolean equation is true or false.x ′ y ′ + x ′ z + x ′ z ′ = x ′ z…
A: Considering the LHS: f1=x'y'+x'z+x'z' =x'y'+x'z+z' =x'y'+x' =x'1+y' =x' ....1…
Q: The two wattmeter method is used to measure the power in a three-phase load. The wattmeter readings…
A: Given- Three phase load-Wattmeter readings=400W & (-35) WTo Find-The total active power Pactive
Q: An alternating current is having an equation I = 125.6 sin 296 r. Find: (1) Frequency (2) R.M.S.…
A: We have an alternating current with the equation of, I = 125.6 Sin 296 t…
Q: Simplify F(A, B₁C₁D₁E) = {m (0.4, 7, 8, 9, 12, 16, 18, 20, 22, 23, 24, 25, 26, 27, 28, 30) woing а)…
A: Given data: FA,B,C,D,E=∑M0,4,7,8,9,12,16,18,20,22,23,24,25,26,27,28,30 Find (a) K-map.
Q: 1. A 70-Vac source has the following waveform. Determine: a. Vpk b. Vpk-pk C. Vrms d. Period e.…
A: Given a 70V AC source waveform (Vrms = 70V) Asked for the following Vpk Vpk-pk Vrms Period…
Q: 10. In a step-down transformer, the number of turns in the secondary coil is 20 and the number of…
A: Given data, Number of turns in secondary coil Ns=20 Number of turns in primary coil Np=100 Voltage…
Q: Problem 5. A coil has a current of 50 mA flowing through it when the applied voltage is 12 V. What…
A: Given, Coil current, I=50 mA Applied voltage, V=12 V
Q: Q1 Determine the Laplace Transform of the following functions by using the Laplace Transform Table.…
A: Given function a)e-5tsin3t
Q: This configuration can overcome the disturbances. Close-loop System Open-loop System Closed-loop…
A: Definition: The expression control system is a set of mechanical or electronic devices that…
Q: 3 phase, 220 k 50Hz transmission line consists of 1.5 cm radius conductor spaced 2 metres apart in…
A:
Q: Power supply to a 10 pole induction motor is supplied by 4 pole alternator which is driven at 1500…
A: Given- 10 pole induction motor. 4 pole alternator. No. of pole P=4. Speed of alternator Ns=1500 RPM.…
Q: Q27. A 15 V source is connected across a 120 resistor. How much energy is used in three minutes? 938…
A: Given V= Voltage = 15V R= Resistance = 12 ohms Time = 3 minutes The energy used in the given time…
Q: Example 3.5 o Evaluate both sides for the field D = 2x yax + rectangular parallelepiped X = 0 and 1…
A:
Q: • Calculate the average and rms values of the following periodic voltage signal. V(1) in volt 300…
A:
Q: Q5) For the waveform shown below, find Vrms v(t) A 2 LAA: 4 6 l10 t -1
A: The given waveform is shown below. Find Vrms.
Q: A 250 V DC shunt generator has a constant loss of 1250 W. Find the load current for maximum…
A: Solution: Shunt generator; V=250 v, Constant loss =1250 W, Find the load current for maximum…
Q: A PN flip-flop has four operations: clear to 0, no change, complement, and set to 1, when inputs P…
A: It is given that: A PN flip-flop has four operations: clear to 0, no change, complement, and set to…
Q: (e mra Given an amplifier with an effective noise temperature of 15,000 K and an 8MHZ bandwidth,…
A: Given- Temperature = 15000 K Bandwidth = 8 MHz To find- Thermal noise level =?
Q: In the following circuit, find the current Ix, and the power associated to the dependent source.…
A: Given data, V=5 V, Vx=1 V Circuit diagram is given as,
Q: The following data are obtained for 7.5 hp, 28A, 4-pole, 208V, 60Hz, Y-connected stator squirrel…
A: The electromagnetic induction is optimized in squirrel cage motors by the rotor bars interaction…
Q: 10. A 47 resistor and a capacitor with a capacitive reactance of 120 are in series across an ac…
A: SOLUTION GIVEN--> LET RESISTOR = R ohm…
Q: In the network below, find the power associated to the current source, for V1 = 8 V. V₁ 24 Select…
A:
Q: 1A ( 4 ww 3Ω 8F + - The circuit above is in DC steady state. What is the value of v, in volts? VC 5Ω…
A:
Q: Two capacitors of capacitances C₁ = 0.1 µF and C₂ = 0.2 µF are connected in series across a 300 V…
A: Given: Two capacitors are connected in series. Capacitance, C1=0.1 μF. Capacitance, C2=0.2 μF.…
Q: What is the reserve capacity, if the maximum demand of generation of power is 50 MW, the load factor…
A: Given, Maximum demand MD=50 MW. Load factor LF=60%=0.6. Plant capacity factor PCF=50%=0.5.
Q: 4. An emf e₁ = 100 sin 2л60t is in series with an emf e₂ = 120 sin 2л60t. a. Sketch the waveform of…
A: The emf connected in series can be added to form a single emf source. The given sinusoidal…
Q: What is RG rating of coaxial cable? Give detailed answer please
A:
Q: Check the linearity of the given systems: a) y(n) = 4x(n - 7) b) y(n) = 4x(6n)
A:
Q: Sol Axit A y(t) = x(t)h(t). = x(t) @ [s(t) = S(t+1)] - = X(t) Sit) - X(t) @ S(t+1) = X(t) = x (t+1)…
A: Given: Solution of a question. To do: We have to just explain last step.
Q: 4. The circuit shown in Fig. 2.9-4 is known to contain only resistors and independent sources. (i)…
A:
Q: A 50 km long transmission line supplies a load of 5 MVA at 0.8 p.f. lagging at 33 kV. The efficiency…
A: We have an transmission line which supplies a load we have been asked to calculate the volume of…
Q: An electric supply company having a maximum load of 50 MW generates 18x 10^7 units per annum and the…
A: We have been given data of an electric company supplying electricity which has, Maximum demand = 50…
Q: Determine the efficiency of a high frequency induction furnace which takes 10 minutes to melt 1.815…
A: To determine the efficiency of a high frequency induction furnace, we need the specific heat of…
Q: A shunt generator has a full load current of 196 amp. at 220 V. The stray losses are 720 watts and…
A:
Step by step
Solved in 2 steps
- Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?Explain the following 1. Diffrence between DC and AC Electricity. 2. how to convert rectangular form to polar form and polar form to rectangular form. 3. why need to improve a power factorThe current through the 20-Ohm inductive reactance is given. What will be the sinusoidal expression for voltage.i=-6 sin(wt-30°)
- Let's say you measure t1/2 to be 0.037 seconds and the resistance in the circuit is 68 Ohms. Then what is the capacitance in micro Farads? Answer in micro Farads.Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitorA sinusoidal current of 5 Arms is flowing through a series combination of a resistor and Inductor. The value of R is 45 ohms and that of the inductance is 15 mH and a frequency of 60 Hz. Find the magnitude and the phase angle of the voltage across the combination. (Hint: you can use phasor diagram). Select one: a. [V]=28.89, angle=9.39 b. IV]=25.60, angle367.00 c. [V]=128.01, angle3D10.18 d. IVl=226.77, angle=D7.16
- Write a report to compare between Ac Through capacitance and AC through in inductance then: For the circuit shown beside, find the total impedance between a and b and Circuit current (I)2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
- A 50-µF and 100-µF capacitors are connected in series and across a 100 sin (wt + 30o) voltage. Write the equation of the current.a. 1.26 sin (wt + 120o) c. 5.65 sin (wt + 120o)b. 1.26 sin (wt + 90o) d. 5.65 sin (wt + 90o)sWhat impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…