If a 50 mV r.m.s. input signal is applied to the amplifier in Fig. 19.68, what is the peak-to-peak outputvoltage? Given that g„= 5000 µs.[920 mV]VDD+ 12 V1.5 kn R,C3 vout10µFVinoHE10 μFR,=10 k2C2I µF10 M2 RG1 kN ZRsFig. 19.68

Answered: Image /qna-images/answer/ea2a8336-f19f-4ff1-a2b4-ee71e13b641b.jpg

Answered: If a 50 mV r.m.s. input signal is…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the output resistance (ZO) of the self-biasing JFET amplifier circuit in the figure. JFET parameters are: loss=10mA,gm=10m01, Vp=-4V. a) b) C) d) Vi 41. RD=3.6k0 10 μF VDD=12V 10 μF Rs 1.1 k 3.6 kohm 1 kohm 1.1 kohm O 4 ohm VO
Given is the buck-boost(Cuk) converter with the following data: Input voltage Vg = 42 V Output voltage V = 24 V Switching frequency fş = 200 kHz Load resistance R = 10 Q a. Determine, D,V₁, V₂, 1₁, and 1₂ b. sketch the inductor voltage and capacitor current waveforms indicating time and magnitude values. c. Determine the value of L₁,L₂, and C, so that Al₁ =1.2% of I₁, Al₂ -3% of 1₂ and Av₁ = 2% of Vg. d. Sketch i(t), 1₂. (t) and v₁ (t) V₂ 4₁ L₁ m C₁ 11 L, ron į₂ C₂ HH 1/2 R
Determine all DC and AC values and the quiescent power dissipation for the CE amplifier shown. Use 25 mV/IE for re. Draw the equivalent AC network. C₁ Vi 1 μF www ww R₁ 22 ΚΩ R₂ 4.7 ΚΩ Vcc +15 V www Rc 2.2 ΚΩ C₂ 1 μF BDC = 90 Bac = 100 RE 1.0 ΚΩ out
3) Consider the transistor circuit below. Assume the input is biased such that the transistor works normally, and ignore any internal resistances in the transistor. For the calculations in this problem, you may assume ß > 1. a) Consider small voltage changes Vin and Vout at the input and output (i.e., ignore bias voltages). Compute the voltage gain G = Vout/Vin- +Vcc Rc b) Compute the input impedance. Zin = Vin/lin Vout c) Compute the output impedance. Zout = Vout/lout Ra Ignore the transistor impedance. Vin
DETERMINE THE OUTRUT VOLAGE (VO) OF A DIFFERENTIAL AMPURER FOR THE INPUT VOLTAGES f 300 miorovolt and 240 mi crovolt. THE DIFFEILENTTAL GAIN OF THE AMPLIEX Is 5,000 and THE VALUE OF CMRR S Ca> 100 ond (b) 105. THE DIFFENRUITAŁ MPUFIER FOR THE GIVEN DATA Is REPRESENTED AS SHOWN BELOW: . .ge. = 300 miorovolf V2 = 240 microvoit Ad= 5000
ELECTRONICS II (EETE3102N) 4 An operational amplifier has a high input impedance and low output impedance. Do you think having those impedances are good or not? Explain your answer. ut of Maximum size for new files: 100MB estion - Files You can drag and drop files here to add them. Accepted file types All file types G ENG 12 DELL F10 F11 F12 PrtScr F3 F4 F5 F6 F7 F8 F9 F2
1) Obtain the T.F of the op-amp cct. shown below: C iz R2 e'
Question 49 Select the appropriate response True or False: The relationship within a channel between amplitude and frequency is referred to as the frequency response. True O False Submit Response Question 50 Select the appropriate response Name a cable design philosophy for amplifier spacing in the forward path, where the total loss of the amount of coax cable and passive device loss in the network before an amplifier will equal the gain of the amplifier. Ⓒunity gain Ⓒamplifier gain Ofrequency gain Submit Response ✔ loss / gain design
p1:Choose the values of Rp. Rs and RL for the JFET amplifier circuit in figure that will result in gain of 18.062dB.Assume that Ipss=8mA, Vp-5v ,rd=0 Vpo/VDD=0.375, and Ipo/Ipss-0.25. Calculate Ay, Zi, Z, A, and Sketch Vo. HH 10u HH K On m Sosin2
T h parameter values of the given Common-Emitter Transistor circuit is h21=-80, h11=45 [ohm], h22=12.5[micro ohm], h12=5x10^-4. Determine the value of RL such that when RL is connected, the current gain iL/i1=79 and the input resistance v1/i1 value is less than 100 ohm.
3-) a) For the circuit given below find the three terminal voltages and the three terminal currents. Assume ß= 100. b) By drawing a small-signal model find the gain Avo, where Avo is no load voltage gain i.c Vand V is no input signal applied input of the amplifier. c) If a signal, vsig, with output resistance 1 k2 is attached to the input, and the output is open, what is the overall voltage gain, vo / vsig? 2K 13K IK XIL F +15 V Vo
k1:Choose the values of Rp. Rş and R1 for the JFET amplifier circuit in figure that will result in gain of 18.062dB.Assume that Ipss=8mA,Vp=-5v ,rd=o0N Vpq/VDD=0.375, and Ipo/Ipss=0.25. Calculate Ay, Zi, Z, A¡ and Sketch Vo. RD1 uF HE 10 uF HE koh m RS 50si n(2 10>

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

If a 50 mV r.m.s. input signal is applied to the amplifier in Fig. 19.68, what is the peak-to-peak output voltage? Given that g„ = 5000 µS. [920 mV] Vpp + 12 V 1.5 kn ER, C3 V. 10µF VinoHE 10 μF R,=10 k2 C2 I µF 10 ΜR I kn{Rs Fig. 19.68