2.▷522, 258pxyağ-kütle sönümleyici sistemi aşağıda verilmiştir.771- 10 kg. b 30 N-s m. k 1000 Nm. P-10N and ws= 2 rad/sifwhat is the steady state response at the output -v(t) = ? inputp(t)=?CODNp(t)=P sin cr661 x 308pxBoyut: 57.4KBCasper

Please refer below Images for the solution.

Answered: if 2. m= yağ-kütle sönümleyici sistemi…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.6P

See similar textbooks

Similar questions

The response of a system 1s given by x(t) = 0.003 Cos Böt +0.0045in 30t m. Defermine the amplitude Og motion, the frequency in Hz, the frequency in rad/s, the frequency n rpm, the phase angle and the responce in the form of x(t)= Asn(wk tp) og mction, the period
1 Problem You are given the following data (below) showing the steady-state output response, x(t), of a mass-spring-damper (stable, LTI) system to a sinusoidal input u(t) = A sin(wt). This snapshot is the response after all the transients have decayed (the time is shifted to start at zero for conve- nience). x 0.5225 Displacement pu(t) Sinusoidal force input x 0.1041 1.5 1 Y2 х 0.2783 Y1.372 0.5 h ok -0.5- -1 -1.5 x(t) M Assume: bl u(t) x(t) Horizontal Plane (no gravity) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Time (sec) www k Using only the data provided above (the blue line is the input u(t) and the red line is the output x(t)), determine: 1. The frequency of the input in rad/s 2. The amplitude of the input, A 3. The frequency of the output in rad/s 4. The output-input ratio |G(iw)| = max(x(t)) max(u(t))' at the particular input frequency shown. 5. The phase (also called phase lag) of the output, $, at the particular input frequency shown in degrees. Note the phase is generally…
The temperature of a catalysed exothermic reaction is being maintained at T1°C as it promotes generation of a particular product. It is proposed to control the temperature with a proportional only controller of gain Kc. The temperature dynamics of the reactor can be modelled as a mixture of a CSTR (1st order) and PFR (dead time) to changes either in inlet temperature, or in the heating/cooling jacket flowrate via Ke-tas Ts+1 i) Considering a change in inlet temperature show why a 1st order model for a CSTR and a dead time model for a PFR are appropriate. CSTR - continuous stirred tank reactor PFR - plug flow reactor
PLEASE GIVE COMPLETE AND DETAILED SOLUTION The oven shown in Figure 1 has a heating element, qi with capacitances C = 50 J/K. The corresponding temperature is T and ambient temperature is Ta. The thermal resistance of the oven wall is R = 2 K-s/J. The system has a steady-state error in the response, T(t) to a change in the reference input. The steady state error can be reduced if a proportional control action, Kp is included in the controller. Determine the range of values of Kp of the system so that the steady state error is lower than 0.4. (Hint: Kindly determine the steady state error at value 0.4)
iv. G(s): = 54 s²+12s+36 a) Find the location of the poles, natural frequency and damping ratio values. b) Determine the forms and write the general expression for the unit step response. c) Find Css (steady state value) and Peak value:.... d) ******** Revise each transfer function to produce unit step response double approximately two tim slower ....................
2- Using Matlab, what are the step response curves of the closed-loop system, as shown in fig.1. the feedback represents the second-order dynamic system. (fill in the following table) For=0.4 Wn 1 3 6 9 10 R(S) 0.1 0.3 0.6 0.9 1 For w 5 rad/sec 3 Settling time Peak response 2 Wn s(s+23wn) Settling time Peak response C(s) Discuss the follow Which parameters or w occur on the rise time of the response? Which parameter increases the speed of response? Which parameters can be decreases the response amplitude? Which parameter decreases the steady error state? fig.2
(c) An electronic Pl temperature controller has an output p of 15 mA when the set point equals the nominal process temperature. The controller response to step change in the temperature set point of 3 mA is shown below. t(s) 0- 0+ 20 60 80 Determine the controller gain K, and the integral time.r p (mA) 8,0 6,8 6.0 4.4 3.6
H.w 2: The open loop response, that is, the speed of the motor to a voltage input of 20V, assuming a system without damping is dw 20 = (0.02) + (0.06)w. dt If the initial speed is zero (w(0) = 0) ,and using the Runge-Kutta 4th order method, what is the speed at t = 0.8s? Assume a step size of h = 0.4s.
össlg äbäi What is the the transfer function of the first-order system which has the impulse response curve as in * ?the following figure Impulse Response 1.8 1.6 1.4 1.2 System: sys Time (seconds): 0.333 Amplitude: 0.737 1 0.8 Slop 0.6 0.4 0.2 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 Time (seconds) 1/(s+3) O 2/(s+3) O 6/(s+3) O No one of the answers in a, b, and c ( Amplitude 2.
A test was undertaken to find the dynamic properties of a SDOF system. The measured transient response recorded is shown in Figure QA2a. If the stiffness of the system is 1,000 N/m estimate: i) the damping ratio, ii) the undamped natural frequency, and iii) the mass of the system. Displacement (m) 0.08 0.06 0.04 0.02 O -0.02 -0.04 -0.06 -0.08 Figure QA2a 0.5 Time (s) 1.5 2
16:13 1 Done A dewisprod.uwe.ac.uk AA [syn3-alhinai) Dewis @ UWE UWE University Wetef Bristol gn GCET Test 1 (Chapters 2, 3 and 4) The Questions Information Question 1. Submit All Answers Find the steady state solution of the forced Mass-Spring-Damper with the Time Left following parameters undergoing forcing function F(t). Question 1 - m = 4.2 kg, c= 31 Ns/m, k = 1124 N/m, F(t) = 39 cos(6t) not complete Question 2 in the form of x(t) = A cos(6t – 8) not viewed yet Question 3 Enter your answers for A and & to four decimal places in the appropriate not viewed yet Question 4 boxes below: not viewed yet А: 8 :
For the pole plot given below, which pole will have the fastest decrease in exponential transient response? jw O Save X X X X k z y x k

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning