Hot sand cools off faster at night than plants and vegetation. Then, the specific heat capacity of sand is * less than that of plants more than that of plants likely the same as that of plants not enough information to answer

Hot sand cools off faster at night than plants and vegetation. Then, the specific heat capacity of sand is * less than that of plants more than that of plants likely the same as that of plants not enough information to answer

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter20: The First Law Of Thermodynamics

Section: Chapter Questions

Problem 20.7OQ: The specific heat of substance A is greater than that of substance B. Both A and B are at the same...

See similar textbooks

Similar questions

(a) What is the rate of heat conduction through the 3.00-cm-thick fur of a large animal having a I .40-m surface area? Assume that the animal's skin temperature is 32.0 , that the air temperature is 5.00 , and that has the same thermal conductivity as air. (b) What food intake will the animal need in one day to replace this heat transfer?
One easy way to reduce heating (and cooling) costs is to add extra insulation in the attic of a house. Suppose a single-story cubical house already had 15 cm of fiberglass insulation in the attic and in all the exterior surfaces. If you added an extra 8.0 cm of fiberglass to the attic, by what percentage would the heating cost of the house drop? Take the house to have dimensions 10 m by 15 m by 3.0 m. Ignore air infiltration and heat loss through windows and doors, and assume that the interior is uniformly at one temperature and the exterior is uniformly at another.
Rubbing your hands together warms them by converting work into thermal energy. If a woman rubs her hands back and forth for a total of 20 rubs, at a distance of 7.50 cm per nub, and with an average frictional force of 40.0 N, what is the temperature increase? The mass of tissues warned is only 0.100 kg, mostly in the palms and fingers.
A high-end gas stove usually has at least one burner rated at 14 000 Btu/h. (a) If you place a 0.25-kg aluminum pot containing 2.0 liters of water at 20.C on this burner, how long will it take to bring the water to a boil, assuming all the heat from the burner goes into the pot? (b) Once boiling begins how much time is required to boil all the water out of the pot?
An astronaut performing an extra-vehicular activity (space walk) shaded from the Sun is wearing a spacesuit that can be approximated as perfectly white ( e=0 ) except for a 5 cm × 8 cm patch in the form of the astronaut's national flag. The patch has emissivity 0.300. The spacesuit under the patch is 0.500 cm thick, with a thermal conductivity k 0.0600 W/m , and its inner surface is at a temperature of 20.0 . What is the temperature of the patch, and what is the rate of heat loss through it? Assume the patch is so thin that its outer surface is at the same temperature as the outer surface of the spacesuit under it. Also assume the temperature of outer space is 0 K. You will get an equation that is very hand to solve in closed form, so can solve it numerically with a graphing calculator, with software, or even by trial and error with a calculator.
(a) The number of kilocalories in food is determined by calorimetry techniques in which the food is burned and the amount of heat transfer is measured. How many kilocalories per gram ale there in a 5.00-g peanut if the energy from burning it is transferred to 0. 500 kg of water held in a 0.100-kg aluminum cup, causing a 54.9- temperature increase? Assume the process takes place in an ideal calorimeter, in other words a perfectly insulated container. (b) Compare your answer to the following labeling information found on a package of dry roasted peanuts: a sewing of 33 g contains 200 calories. Comment on whether the values are consistent.
The thermal conductivities of human tissues vary greatly. Fat and skin have conductivities of about 0.20 W/m K and 0.020 W/m K, respectively, while other tissues inside the body have conductivities of about 0.50 W/m K. Assume that between the core region of the body and the skin sin face lies a skin layer of 1.0 mm, fat layer of 0.50 cm, and 3.2 cm of other tissues. (a) Find the R-factor for each of these layers, and the equivalent R-factor for all layers taken together, retaining two digits. (b) Find the rate of energy loss when the core temperature is 37C and the exterior temperature is 0C. Assume that both a protective layer of clothing and an insulating layer of unmoving air a absent, and a body area of 2.0 m2.
Suppose a person is covered head to foot by wool clothing with average thickness of 2.00 cm and is transferring energy by conduction through the clothing at the rate of 50.0 W. What is the temperature difference across the clothing, given the surface area is 1.40 m2?
A certain steel railroad rails 13 yd in length and weighs 70.0 lb/yd How much thermal energy is required to increase the length of such a rail by 3.0 mm? .Note: Assume the steel has the same specific heal as iron.
Compare the rate of heat conduction through a 13.0-cm-thick wall that has an area of 10.0 m2 and a thermal conductivity that of glass wool with the rate of heat conduction through a 0.750-cm-thick window that has an area of 2.00 m2, assuming the same temperature difference across each.
In a study of healthy young men[1], doing 20 push-ups in 1 minute burned an amount of energy per kg that for a 70.0-kg man corresponds to 8.06 calories (kcal). How much would a 70.0-kg man's temperature rise if he did not lose any heat during that time?
One method of converting heat transfer to doing work is for heat transfer into a gas to take place, which expands, dong work on a piston, as shown in the figure below. (a) Is the heat transfer converted directly to work in an isobaric process, or does it go through another form first? Explain your answer. (b) What about in an isothermal process? (c) What about in an adiabatic process (where heat transfer occurred prior to the adiabatic process)?