Hot fluid enters a heat exchanger with 77 °C and leaves at 37 °C, cold fluids enters with 17 °C and leaves at 40 °C, then the type heat exchanger can be: Select one: A. Counter flow or Cross flow heat exchanger. B. Only Counter flow heat exchanger. C. Parallel flow or Counter flow heat exchanger. D. Parallel flow, Cross flow or Counter flow heat exchanger. E. Parallel flow or Cross flow heat exchanger.

Hot fluid enters a heat exchanger with 77 °C and leaves at 37 °C, cold fluids enters with 17 °C and leaves at 40 °C, then the type heat exchanger can be: Select one: A. Counter flow or Cross flow heat exchanger. B. Only Counter flow heat exchanger. C. Parallel flow or Counter flow heat exchanger. D. Parallel flow, Cross flow or Counter flow heat exchanger. E. Parallel flow or Cross flow heat exchanger.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a) In a concentric-pipe heat exchanger, one of the fluids is a condensing vapour and the other is the coolant. Sketch the variation in fluld temperatures of two fluids as they flow through the heat exchanger. Indicate clearly the Inlet and outlet of the coolant and its direction of flow. b) For the case outlined in a) above, the heat-transfer rate, Q, between the two fluids is given by Q =U. Ą ATLI where U, Is the overall heat-transfer coefficient for the heat exchanger, based on the outside surface area of the inner tubo, A, Is the outside surface area of the inner tube and AT Is the relevant temperaturo difference given by ATLM = (T₂-T₁) Tv-T₁ In where subscript v refers to the condensing vapour and subscripts 1 and 2 refer to the Inlet and outlet temperatures respectively of the coolant. 1) State the assumptions used to arrive at the above equation. Explain why the "log-moan" temperature difference above is a more appropriate temperature different for heat exchangers than, say, the…
2-A cross-flow heat exchanger with both fluids unmixed is used to heat water (c, = 4.18 kJ/kg•K) from 40°C to 80°C, flowing at the rate of 1.0kg/s. What is the overall heat transfer coefficient if hot engine oil (c, = 1.9 kJ/kg-K), flowing at the rate of 2.6 kg/s, enters at 100°C? The heat transfer area is 20 m2. (Note %3D that you can use either an effectiveness or an LMTD method. It would be wise to use both as a check.)
Problem 2 A counterflow heat exchanger with both fluids (i.e., water and air) being unmixed. The water has a flow rate of 0.07 kg/s, enters the heat exchanger at 400 K and leaves at 300 K. The water is cooled by air that enters at 0.75 kg/s and 250 K. Cp for the water and air are 4200 J/kg.K and 1007 J/kg.K, respectively. 1. Explain how do you calculate the rate of transfer for a heat exchanger. 2. If the overall heat transfer coefficient is 150 W/m² K, Calculate the total heat transfer rate through this heat exchanger? 3. What if you use a parallel flow heat exchanger instead of the counter flow heat exchanger, determine the total heat transfer rate? 4. What are the main differences between parallel and counter flow heat exchangers and which heat exchanger is better for refrigeration and air conditioning application.
Q#01: Define the following: a) Heat Exchanger. b) What is the difference between a condenser and heat exchanger? c) Why every condenser is not a heat exchanger? d) What are mixed and unmixed flow heat exchangers? Explain with the help of an example.
Q#01: Define the following:a) Heat Exchanger.b) What is the difference between a condenser and heat exchanger?c) Why every condenser is not a heat exchanger?d) What are mixed and unmixed flow heat exchangers? Explain with the help of an example.
DS Community Downl... Haritalar EOkuma list iş İÇİN Giriş yap 口口山凸9 İNGİLİZCE An air-cooled condenser is used to condense isobutane in a dual geothermal power plant. Isobutane, air entering at 22 oC with a flow of 18 kg/s (cp = 1.0 kJ / kg.K)is condensed at 85 oC. The total heat transfer coefficient for this heat exchanger is 2400 W/m2.K and surface area is 2.6 m2. What is the output temperature of the air? Çeviri yap: Google Bing
There is a tubular heat exchanger with the outer tube radius of 4 cm, the inner tube radius of 2 cm, and the length of 15 m. Your goal is to process milk at a rate of 3 kg/s. The inlet temperatures of milk and hot water are 4 °C and 90 °C, respectively. The specific heat capacity of water is 4.19 kJ/(kg °C), and the specific heat capacity of the milk is 4.0 kJ/(kg °C). a. If you are using a con-current flow with a water flow rate of 6 kg/s, the outlet temperature of hot water is measured at 70.13 °C. What is the outlet temperature of the milk? Show your calculation steps and compare your result with that given by the virtual experiment. b. If you are using a counter-current flow, the outlet temperatures of hot water and milk are measured at 68.78 and 48.46 °C, respectively. What is the flow rate of water? Show your calculation steps. Try these conditions, and compare the temperatures with the result given by the virtual experiment. c. During this pasteurization process, what is the…
Shown below is a heat exchanger used to cool down the liquid in the tube. The shell is well insulated. (2) If inner walls of the shell are system boundaries, and liquids within system boundaries (the liquid between the shell and tube and the liquid in the tube) are chosen as the system, select the correct energy balance equation._____________ A. B. C. D.
Refrigerant condenses in the tubes of a cross flow heat exchanger at 41 °C, 16.7 MJ/hr is rejected form the refrigerant by air "c= 1005 J/kg.K". Air enters at 24 °C and leaves at 37 ;c. What is heat transfer area of the refrigerant side (m) when the overall heat transfer coefficient refrigerant side on the is 151 W/m".°C? Hint use LMTD method and assume a correction coefficient of 100%
(1) A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large industrial gas turbine engine. The flow rate of cooling water through the inner tube (D; = 20 mm) is 0.5 kg/s, while the flow rate of oil through the outer tube (Do = 45 mm) is 0.3 kg/s. The oil and water enter at temperatures of 100 and 30°C, respectively. A) What is the main difference between parallel and counter flow heat exchangers? B) How long must the tube be made if the outlet temperature of the oil is 60°C? C) If the heat exchanger is changed to parallel flow heat exchanger, how long must the tube be made if the outlet temperature of the oil is 60°C?
5) During an experiment, a plate heat exchanger that is used to transfer heat from a hot-water stream to a cold-water stream is tested, and the following measurements are taken: Hot water Cold water stream stream 38.9 Inlet temperature, °C Outlet temperature, "C Volume flow rate, L/min 14.3 27.0 19.8 2.5 4.5 The heat transfer arca is calculated to be 0.0400 m. (a) Calculate the rate of heat transfer to the cold water. (b) Calculate the overall heat transfer coefficient. (c) Determine if the heat exchanger is truly adiabatic. If not, determine the fraction of heat loss and calculate the heat transfer efficiency. (d) Determine the effectiveness and the NTU values of the heat exchanger. (Answers: (a) 1724 W (b) 3017 Wiw C (c) the heat exchanger is not adiabatic so heat loss 16.4% and heat transfer efficiency 83.6% (d) effectiveness 44.4% and NTU 0.697) Hot water 38.9°C 19.8°C Cold water 14.3°C 27.0°C
In a parallel flow heat exchanger, hot water at a flow rate of 1 kg/s is cooled from 90° C to 60 °C with a cooler at a temperature of 40 °C at a flow rate of 2 kg/s. Total heat transfer coefficient 1000 W / m2.K. Cph = Cpc= 4182 J/kgK According to this;a) determine the required area for the heat exchanger using the logarithmic mean temperature difference method.b) determine the required area for counter-flow heat exchanger status.c) determine the required area, taking into account the state of a cross-flow heat exchanger in which one flow is mixed, in which the other flow is not mixed. d) assume that the output temperature of the hot fluid is not given, take the area 6.42 m2 for the parallel flow heat exchanger state and calculate the output temperature of the hot water using the efficiency-NTU method.