he structure in Figure Q4 is made of two members, AB and BC, both made of metal with a Young's Modulus E = 110.41 GPa. Member AB has a rectangular cross-section, whose sides measure a = 35 mm, and b = 81 mm.        Figure Q4   Calculate the Second Moment of Area of member AB with respect to its strongest orientation. Use π = 3.14159 in your calculations if needed. Express your answer in the unit: mm4.  Report your answer to 2 decimal places.

Q: In fig. shown. Pind the reaction force on paít(Bc) . OZ07 kpd L = 107 HRir %3D oiL D=75mm Y.d =0.88…

A:

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

A: given; torque(T)=7Nmcoefficient of friction(μ)=0.35angle(θ)=600            =π180*60…

Q: A simple harmonic motion as shown in Figure Q1(a) has a maximum velocity of (P+1) m/s with (Q+2)…

A: Given data: matrix num (ad200107) Vmax=P+1 m/sVmax=1=1=2m/sT=Q+2 sT=2 sx0=R+1 mmx0=7+1=8mm

Q: At 1:00P.M, a thermometer reading is 70°F is taken outside where the air temperature is -10*F. At…

A:

Q: naded area y 100 mm 140 mm 50 mm 140 mm -200 mm- 2.

A: Divide shaded area as shown above

Q: A solid shaft transmits 30 kW at 3 rev/s. Determine the cubic diameter of the shaft (d3 ),if the…

A:

Q: Why is it necessary to have oil under pressure in a torque convertor? During torque conversion what…

A: Torque converter is a sealed unit it consist of automatic transmission fluid.It works as the  fluid…

Q: nnecting rod is made as I section? Why do some connecting rods have hole drilled from the small end…

A: The allows oil to pass from the big end to the thrust section where there is friction against the…

Q: TIG welding standard example ха Find the procedure parameters for the

A: Tungsten Inert Gas (TIG) welding, also known as Gas Tungsten Arc Welding (GTAW), is a type of arc…

Q: Steam is generated at 4.1 Mpa and 440 degrees Celsius and the condensing pressure is 105 Kpa. Find…

A:

Q: A Cascade refrigeration system using flash tank and intercooler is operating an evaporator with a…

A: INTRODUCTION : The refrigeration is a process of maintaining a place at a lower temperature as…

Q: A single plate friction clutch with both sides of plate being effective is used to transmit power at…

A: Find the power and axial thrust.

Q: Between a solid mass of 10 kg and floor, two slab of isolator, natural rubber and felt are kept in…

A: Given that, Mass of the solid mass, m=10 kg,Stiffness of natural rubber, kr=3000 N/m,Equivalent…

Q: Determine the value of Elv (in Ib ft³ )at midspan for the beam loaded by two concentrated forces if…

A:

Q: Figure Q2 shows an 11 m long steel beam AC of uniform cross-section, simply supported at left end A…

A: Reaction force at support A is RA = 152.5 kN. Reaction force at support B is RB = 187.5 kN.

Q: 0.05 m3 of nitrogen contained in a cylinder behind a piston is initially at 1.2 bar and15°C. The gas…

A:

Q: Question 3: The beam is subjected to the uniform distributed load shown. Draw the shear and moment…

A:

Q: . . coffee at breakfast O drinks O drink O drank

A: Drinks- present Drank- simple past Drunk- past principle

Q: Determine the reaction at the supports A and C of Structural Truss shown.

A:

Q: To move something that weighs more than you do, using a lever, move the item closer to the _____.

A:

Q: An assembly of a steel bar enclosed within an aluminium alloy tube is shown in Figure 1(b). The tube…

A: Tensile strain is the deformation or elongation of a solid body caused by a tensile force or stress.…

Q: 0.60 m the given loading, determine all members. 2.7 kN 1.20 m 1.2 kN H a. Use the Method of Section…

A: Joint A-FAB2.29=FAC2.29=1.2KN1.2             FAB=2.29KN T              FAC=2.29KN CJoint…

Q: calculate translational function of a rotational system θ2 (s)/t(s)

A: Solution: Given Data:

Q: Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces…

A:

Q: QI Define five of the following with sketch. 3- AA2024 4- Rolling 5- Wire drawing 1-Taper turning 2-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: A is rotating in the counter-clockwise direction at a speed of 180 r.p.m. increasing at the rate of…

A: NAO=180rpmωAO=2π×18060=18.85rad/sOA=180mm=0.18mCB=240mm=0.24mAB=360mm=0.36mBD=540mm=0.54m

Q: A Mansard roof truss is loaded as shown. a) Identify, by observation, any zero force members in the…

A:

Q: The pump is to increase the pressure of 0.3 m3/s of water from 100 kPa to 500 kPa. If the pump is…

A:

Q: An assembly of a steel bar enclosed within an aluminium alloy tube is (b) shown in Figure 1(b). The…

A:

Q: installed as shown in the figure. The gage at point 1 is 80 kPa while at point 2 is -46 kPa. If the…

A:

Q: yquandj3iakzjwkoqKd ywuajxjeuiqias jgo4oajzuwuq udiqijNxjd 4. At 1:00P.M, a thermometer reading is…

A: thermometer reading is 70°F is taken outside where the air temperature is -10°F. At 1:02P.M, the…

Q: C3 with spring constants c = 5 ///// ee

A:

Q: The laminated leaf springs are self-damping. Justify, how? What is the purpose served by phosphate…

A: Solution: To Find: (a) How the laminated leaf springs are self damped. (b) What is the purpose…

Q: The variable h designates the arbitrary vertical location of the bottom of the rectangular cutout…

A: It is required to determine moment of inertia of the given shape about x axis at: (a) h = 60 inches…

Q: Q3/ The brakes of a truck travelling at 43 km/h are suddenly applied to avoid a vehicle which has…

A:

Q: Out of the camber and caster, which is measured first and why? How the camber angle can be adjusted…

A: Camber angle is the angle which is measured in the front elevation in-between the wheel plane &…

Q: The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment…

A:

Q: Explain the purpose of the relief valve and one-way check valve in an electric fuel pump. What type…

A: Given question: Explain the purpose of the relief valve and one-way check valve in an electric fuel…

Q: Use appropriate boundary conditions to evaluate the constants in the boundary layer velocity profile…

A: Suppose a fluid moving with a velocity 'u' in a viscous flow and whose vertical distance from the…

Q: For applied load of -300N, give your strain measurement in microstrains for strain gauge 5, having…

A:

Q: Figure Q2 (c) shows a belt drive used to transmit power from elec fan. The electric motor A is…

A:

Q: A pyramid ABCD, the heud poiut A(2,5,4) and base points B(2, 0.5,0), C(O.5,2,0 and D(-1, o, 0).…

A: Given data The points of the given pyramid are  A(2,5,4) with base points B(2,0.5,0) , C(0.5,2,0)…

Q: For the truss shown, assume a cross sectional area of each member is 3.2 in² a. Calculate the stress…

A:

Q: The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close…

A: Answer: IX = 649.05 in4.

Q: The beam shown is subjected to bending moment M 5 kNm. Determine a) Centroid of the cross-section [!…

A: Given data :- moment (M) = 5 kN-m Find the stress at point A and point B.

Q: Find Potontia eneryy

A:

Q: Ex- If the flowrate between two tanks is (e.s m/s). find CH)? KL1.8 Ls Soom LIE30 DI=300 Dg = S0o mm…

A:

Q: If the motorcycle has a deceleration of at = -(0.001s) m/s^2 and its speed at position A is 25 m/s,…

A: Given data: at=-0.001s m/s2VA=25 m/s Need to determine the magnitude of its acceleration when it…

Q: 27 of 32 A thermistor obeys the equation R(T) = A"exp(B/T) ohms, where A = 0.02 Q and B = 3700 K.…

A: Find the temperature .

Q: 200 lb 1.5 ft 200 lb F 4 ft

A: Given:-  To Find:- Couple moment and it's direction

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.