he input to a combinational logic circuit is 4-bit binary number (A, B, C, D). Design the circuit strictly using NAND gate with two outputs (Y1 and Y2) for the following conditions: Output Y1 is low when the input binary number is less than or equal to 7. Output Y2 is high when the input binary number is less than or equal to 7

he input to a combinational logic circuit is 4-bit binary number (A, B, C, D). Design the circuit strictly using NAND gate with two outputs (Y1 and Y2) for the following conditions: Output Y1 is low when the input binary number is less than or equal to 7. Output Y2 is high when the input binary number is less than or equal to 7

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a combinational circuit with 3-inputs and 1-output. The output is equal to logic-1 when the binary value of the input is less than 3. And the output is logic-0 otherwise.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th W R₂ = 5600 PEETHIPPIN R₁ - 4700 M3 M₁ M. 0 a. Indicate and verify the state of each MOSFET and V for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. 오 Ao SV why
4. a. Design a Combinational circuit with three inputs, (A, B, and C) and four outputs, (U, V, W, and X) with the 2- i/p NOR gate only for the following logic. When the decimal value of the input is 4, 5, 6, or 7 the binary output is one less than the input (input-1). When the decimal value of input is 0, 1, 2, or 3, the output is two greater than (input +2) the input. b. A majority circuit is a combinational circuit whose output is equal to 1 if the input variables have more no. of 1's than 0's. The output is 0 otherwise. Design Using Boolean laws, three input Majority circuits with P, Q, and R as input, output Function T and its complement, Prove.
ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG
d) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, The logic "0" will be applied to the burned parts. Draw this circuit.
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, Logic "0" will be applied to the burned parts. The accuracy of the logic circuit you will design Create the table and find the output expressions by shrinking the table with the Karnaugh diagram method.
Implement the function, W using ONE 4-to-1 multiplexer and other logic gates. b) Implement the function, X using ONE 4-to-1 multiplexer and other logic gates. Implement the function, Y using TWO 4-to-1 multiplexer and other logic gates. d) Implement the function, Z using ONE 8-to-1 multiplexer and other logic gates. Table Q1 ВCD Braille A B D W Y 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 A ololO
Consider a family of logic gates that operate under the static discipline with the following voltage thresholds: VI=1.5V, VOL=0.5V, VIH=3.5V, and VOH=4.4V. a. What is the lowest voltage that can be output by an inverter for a logical 1 output? b. What is the highest voltage that must be interpreted by a receiver as logical 0? c. What is the lowest voltage that must be interpreted by a receiver as logical 1?
Draw a half-adder logic circuit using only two gates
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.