gned to trans The inside and outside wall temperatures are to be 2200 ° F and 320 ° F. Determine the most economical arrangement of bricks measuring (9 in x 4; in x 3 in). If they are made from materials one with a k of 0.44 Btu/hr. ft. °F and maximum usable temperature of 1700 ° F and other with a k of 0.94 Btu/hr. ft. F and a maximum usable temperature of 2400 F. Bricks made of each material cost the same amount and may be laid in any manner (but bricks must remain intact, i.e., no partial bricks). After you answer the question, determine the percent increase in heat flux if there are two -in-diameter steel bolts extending through the wall per square foot of wall are. (k of steel = 22 Btu/hr. ft. ° F)|

gned to trans The inside and outside wall temperatures are to be 2200 ° F and 320 ° F. Determine the most economical arrangement of bricks measuring (9 in x 4; in x 3 in). If they are made from materials one with a k of 0.44 Btu/hr. ft. °F and maximum usable temperature of 1700 ° F and other with a k of 0.94 Btu/hr. ft. F and a maximum usable temperature of 2400 F. Bricks made of each material cost the same amount and may be laid in any manner (but bricks must remain intact, i.e., no partial bricks). After you answer the question, determine the percent increase in heat flux if there are two -in-diameter steel bolts extending through the wall per square foot of wall are. (k of steel = 22 Btu/hr. ft. ° F)|

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.3P: 1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of...

See similar textbooks

Similar questions

Draw the thermal circuit for heat transfer through a double-glazed or a double-paned window. Identify each of the circuit elements. Include solar radiation to the window and interior space.
Find the amount of heat lost per hour through a square foot ofbuilding wall composed of 18-in. sandstone and 3/4-in. metal lath andplaster separated by a 1 1/4-in. air space, when the temperature of theroom is 70 °F, the outdoors is 10 °F, and the wind velocity is 15 mph.
Match the appropriate thermal conductivity walue for the given materials Material Thermal Conductivity (K) 4. Diamond 0.026 W/m K B. Copper 2. 0.607 W/m K c. Water 3. 385 Wm K D. Ar 2300 Wm K O a. A-I, B-IV, C-I, D-I O b. A-II, B-I C-I D-IV Oc A-IV, B-II, C-II, D-I O d. A-I, B-I, C-II D-IV
K). average NUSseit Number. 2. A slab of iron with temperature, T1=48 deg C is used to heat a flat glass plate that has an initial temperature of Tg1=18 deg C. Assuming no heat is lost to the environment, and the masses are m;=0.49 kg for the slab and mg=310g for the plate, what is the amount of heat transferred when the two have reached equal temperature? Assume C;=0.11 kcal/kg-deg C for iron and cg=0.20 kcal/kg-deg C for glass.
What is the rate of heat transfer through a piece of celotex 3 ft by 8 ft by 1 inch thickness, if the temperature of one surface is 80 deg. F and of the other surface is 60 deg. F.
R Value: Wall: 0.961m2k/w Floor: 0.676m2k/w Roof: 0.7465m2k/w In a table format show with calculations and research how much money you can save by installing a 115mm layer of insulation (R2.9) in your walls, floor and ceiling over a 5 and 10 year period. Consider the capital costs. Hint: State the current R value of each component. Convert to U value. Calculate new R value of each component (walls, floor and ceiling). Convert to U value. Use Q(W)=A*(change in U)*temperature change. Determine price for installation of new insulation. Determine price saved based on less heat loss through each component separately, then add all values together, and calculate per 5 years and per 10 years. Present all of this information in a table. You do not need to draw any diagrams, simply add the R value in series with your current components R values. Assume the energy cost is 25 cents kWh
Q2- Determine: A small solid at temperature of 85 °C is to be cooled in a cooling chamber maintained at 10 °C. 1- The time required for the temperature of the solid to reach 13 °C if the proportionality constant is a = 0.002/m² with a contacting surface area A = 0.2 m². 2- The temperature of the ball after 30 s. 3- The final temperature of the ball. Bulk environmental temperature = T₁ AZ Surface area, A- Solid T(t) Initial solid temperature, To
[2] A reservoir of hot water kept at 380K is well insulated except for a copper rod with a cross sectional area of 0.25 m? and a length of 0.50 meters. The rod is also well insulated except for its ends and the other end is in a second well insulated reservoir of water held at 280K. a) Determine the rate of heat flow through the copper rod. b) Calculate the temperature at the center of the rod (0.25 meters from either end). Then extend the process to find the temperature at each point 0.1m along the rod. c) Calculate the rate of entropy change at each end of the rod. d) Using your answer for (c), show that the statements "Heat flows spontaneously from high temperature to low temperature." and "Any spontaneous process causes the entropy of the universe to increase." are logically equivalent for situations with heat flow. e) Each reservoir of water holds 1 m of water. With a steady flow established, the power fails so that the heating and cooling of the water ceases. What are the…
I need a KPI for a project that consists of two partsThe first is glasses that monitor objects around them, and alert the person when an object is within the specified distanceThe second part is a glove that senses the heat from a distance. When the temperature reaches above the permissible limit, the person is alerted by means of a vibration motor.The purposes used in the first part:Spectacle shaped frame3 ultrasonic sensors2 vibration motors Arduino Pro NanoThe purposes used in the second part:The glove consists of two layers3 temperature sensorsMotor vibrationArduino Pro NanoMicro-nano charging baseWorking principle of each part:part One ::Objects that are within the distance on which the Ultrasonic has been programmed are monitored, where there is to the right of the glasses and the left of the glasses, and to the front of the Ultrasonic glasses, and there is a vibration motor on the right of the glasses and the left of the glasses. A body is monitored from the front, and this…
Q1- An exterior wall of a house consists of 10.2 cm brick and 3.8 cm gypsum plaster. What thickness of loosely packed rockwool insulation should be added to reduce the heat transfer through the wall by 80%? Thermal conductivity of materials for the wall are Brick: k= 0.7 W/mK Gypsum plaster: k=0.48 W/mK Rockwool: k= 0.065 W/mK
A wall of a house is made from two layers of bricks enclosing a layer of insulation. A radiator is positioned to cover the whole internal surface, and used intermittently when the internal temperature is low. The external surface is exposed to the outside air. Which of the following assumptions could be used to identify the relevant reduced form of the conduction equation to find the temperature in the wall. a. Conduction is mainly in two directions. b. Conduction is mainly in one direction. c. The wall properties are homogeneous. d. Steady conditions exist. e. Unsteady conditions exist. f. There is an internal volumetric heat generation in the wall.
Qi: (50 marks) Find the total heat flux of the composite wall when: B KA = KC = KF = 15 m. K KB = KD = 10 m. K KE = KG = 20 %3D m. K D. Height of B = C = D 4 cm 3 cm 4 cm 6 cm Height of F = G AT = 30 K