Flowrate adjusted with the rotameter together with the collected volume and time elapsed were written in the table below: Write down your measurements in a table: Readings on Duration Water collected in the rotameter (seconds) graduated cylinder (L/h) 1 800 8.320 2 1000 6.770 3 1200 6.160 4 1400 5.180 5 1600 4.470 Water temperature = 25 °C (mL) 1700 1700 1820 1800 1740 Calculated Flowrate (L/h)

Flowrate adjusted with the rotameter together with the collected volume and time elapsed were written in the table below: Write down your measurements in a table: Readings on Duration Water collected in the rotameter (seconds) graduated cylinder (L/h) 1 800 8.320 2 1000 6.770 3 1200 6.160 4 1400 5.180 5 1600 4.470 Water temperature = 25 °C (mL) 1700 1700 1820 1800 1740 Calculated Flowrate (L/h)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flow with a density of 998 kg / m3 at 70 ° C enters the system at a speed of 0.5 m / s and a 20 cm diameter pipe is pumped to a 2.5 m high reservoir with the help of a 7.5 kW pump. With the heater at the exit of the system, 1300 kW of energy is transferred to the water flow. Calculate the exit temperature of the water. (With reference to the height Z1, Z2 = 2.5 m is acceptable, ignore kinetic energy changes.) heater Pa pump and turbine P1 Ws reference plane O--
(b) A pitot-static probe is use to determine the flow velocity by measuring the differential pressure. The pitot formula to obtain the flow velocity is, 2(P- P,) V = where, V is the velocity, P is pressure and pis fluid density. i) The pressure difference sensor use in the system is electronic types and the output of the device is measured in voltage. The output of the pressure device is 3.5 V and the linear relationship between the device and the pressure difference is 10 kPa/V. If the measured fluid is water at 20°C, determine the pressure difference inside the system the water velocity. ii) The Pitot-static tube is also commonly use in aircraft. An aircraft flying at 3000 m above sea level when the differential pressure reading clocked 3 kPa. Determine the speed of the aircraft.
1. Start from the following equations from class notes (treat as given): The shear stress in pipe flow T = -μ- dr du 16 [1-(-)²), AP D² 16μL The fluid velocity in the pipe u = Derive clearly the following results: (a) The shear stress on the wall of the pipe, Tw. (b) The average velocity in the pipe flow, ū. (c) The Darcy friction factor, defined by f where L is the length of the pipe. 8 tw pū² (d) Express the result of (c) in terms of the Reynolds number, Re. (e) Find an expression for the head loss due to shear stress at the wall, AH₁, in terms of f,u, D and L. (f) What are the main assumptions in the fluid flow, in order to analyse the flow in this way?
7. An oil (sp.gr 0.9) is flowing through a 1.2m diameter pipe at a rate of 2.5 m³/s. The kinematic viscosity of oil is 3 X106 m²/s. In order to model this flow, water is used to flow through a 120mm diameter pipe having kinematic viscosity of 0.012X104 m²/s. Find the model discharge and velocity.
Flow (m³ /h) 1 1.5 2 2.5 Pressure difference Ap (bar) 0.005 0.012 0.021 0.034 Kinematic viscosity 10-6 m?/s V (Rough Pipe Radius = 25mm) (Rough Pipe length =L=80cm) Question: An experiment is made using different flow rates in a pipe and pressure differences are given according to the given flow values. According to these; 1. Calculate the pipe roughness height ( e ). 2. Calculate the Reynolds value. 3. Calculate the coefficient of friction f from the Darcy-Weisbach equation. 4. Briefly describe the equations you use and the reasons for using them.
Find the pressure drop between locations a and b for flow in a pipe using the following data: Working fluid: Water Pipe: Stainless steel, Schedule No. 120 Nominal pipe size (cm): 10 Flow rate (m3 /min): 2.271 Temperature (C): 38 Length (m): 45.72 Solve for the following 3 cases: a) Za = Zb =33.5 m, b) Za = Zb + 15 m, and c) Za = Zb + 46 m.
%A l, l. exercisec sheet.pdf -> Q7: Find the value of mass (mo) to move the mass 150 lb. downward the surface T 150 Ib mo H=03 20 Q8: The acceleration of a particle as it moving along a straight line is given by a = 2t-1 m/s. Where t is in seconds. If s = 1 m and v = 2 m/s where t = 0. Determine the particles velocity and position when t = 6s. also determine the total distance the particle travels during this time period. Q9: The van is travelling at 20 km/hr when the coupling of the trailer as A fails. If the trailer has a mass of 250 kg and coasts 45m before coming to rest, determine the constant horizontal force F created by rolling friction which causes the trailer to stop. Q10: The double inclined plane supports two blocks A and B. each having a weight of 10 lb. If the coefficient of kientic friction between the blocks and the palne is uk = 0.1, determine the acceleration of each block. II
'p' (liquid density) 'A' (tank cross sectional area) 'Qin' (Input Flow Rate) Qout' P Figure 1 'h' (head of liquid) 'R' (restriction coefficient) 5m
56.0 mL of two different liquids are poured through a funnel with a narrow exit tube, and the time for all of the liquid to flow through is recorded. Here are some results: time to flow through funnel trial Liquid X Liquid Y 1.60 s 3.62 s 1.52 s 3.44 s 1.44 s 3.56 s Note: the two liquids have the same density. Which statement below is true about these liquids based only on the data in the table? O The intermolecular forces in liquid X are stronger than those in liquid Y. The boiling point of liquid X is higher than the boiling point of liquid Y. The viscosity of liquid X is greater than the viscosity of liquid Y. The surface tension of liquid X is greater than the surface tension of liquid Y. The viscosity of liquid X is less than the viscosity of liquid Y. 3.
QUESTION 1 Three pipes A, B, and C are interconnected as shown in figure 1. The pipe dimensions are as follows: D (cm) 15 10 20 Pipeline L (m) 300 0.01 B 240 600 0.01 0.005 A 15 m 25 m B Figure 1 1.1 Find the rate at which water will flow in each pipe, ignoring the shock losses at P and entry to pipelines A and B. 1.2 Find the pressure at P.
Dimensional Analysis and Hydraulic Similitude (fluid mechanics) 1. Water at 60F at 12 ft/s in a 6-in. pipe. (a) For dynamic similarity, determine the velocity of medium fuel oil at 90F flowing in a 12-in. pipe. (b) Determine the diameter of the pipe that should be used if a medium lubricating oil at 70oF if flowing at a velocity of 50 ft/s. find the: a. velocity : ____________________ fps b. diameter : ____________________ in.
1) At any time, approximately 20 volcanoes are actively erupting on the Earth, and 50–70 volcanoes erupt each year. Over the past 100 years, an average of 850 people have died each year from volcano eruptions. As scientists and engineers study the mechanics of lava flow, accurately predicting the flow rate (velocity) of the lava is critical to saving lives after an eruption. Jeffrey's equation captures the relationship between flow rate and viscosity as: Flow V = Pgt sin(@) 28 сm 10 where p is the density of the lava, g is gravity, t is the flow thickness, a is the slope, and u is the lava viscosity. Typical values are given as follows for the flow rate: u= 4x103 kg/(m.s) ±1% p= 2.5 g/cm³ ±1% t= 28 cm +0.5 cm a= 10° +1 ° g= 9.81 m/s? Determine the likely maximum possible error in the calculated value of the flow rate.