flops A and B, and one input x_in. When x_in = 0, the circuit goes through the state transitions from 00 to 10, to 01, to 11, back to 00, and repeats. When x_in = 1, the circuit will reverse the given sequence. a. Using D Flip-Flop. b. Using JK Flip-flop. Provide the state diagram, state table, state equations, and the circuit diagram.

flops A and B, and one input x_in. When x_in = 0, the circuit goes through the state transitions from 00 to 10, to 01, to 11, back to 00, and repeats. When x_in = 1, the circuit will reverse the given sequence. a. Using D Flip-Flop. b. Using JK Flip-flop. Provide the state diagram, state table, state equations, and the circuit diagram.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

You want to design a synchronous counter sequential (sequential) logic circuit. It will count from 0 to 9 and will not count the decimal digits in the last two digits of your student number. a. List the process steps that you will apply in the design approach. Create the State Chart and State Chart. b. Design the sequential circuit using JK Flip-Flop. Explain each step. Show that it has performed the desired action. last two numbers 02
2. Sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in Figure below. Analyze the circuit: a. Derive the next state and output equations. b. The state table of the circuit. c. Draw the state diagram. A K. 2-t0-1 MUX Y B' CLK
4 7) For the following sequential circuit: a) Tabulate the state table. b) Derive the state and output equations. c) Re-design the circuit using T flip-flops. Q1 Q -y K, K QP Jo Qo Q Ko K Q clock. please solve it as soon as possible
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 0 to 9 and will not count the last two digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last two digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0 and will not count the last digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last digit student num:4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
2. Sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in Figure below. Analyze the circuit: a. Derive the next state and output equations. b. The state table of the circuit. c. Draw the state diagram. A K B 2-t0-1 MUX B' K CLK
Design a sequential circuit using JK flip-flops that controls 4 red leds and gives the desired output shown on the Table . After step 8, the circuit must go back to step 1.a) Build state table.b) Build state diagram .c) Design the circuit .d) Simulate it without any wrong .
You want to design a synchronous counter sequential logic circuit. Counting from 0 to 9 will perform and not count the numbers 0, 3, 5, 8. (a) List the steps you will apply in the design approach. State Diagram and Status Create the table. (b) Design the sequential circuit using Flip-Flops. Explain each step. Desired action show that it does.
Review Questions Question [4] For the given sequential circuit: a. What type of state machine is this circuit and why? b. Determine the flip-flop input equations and the output equations from the circuit. c. Derive the next-state equation for each flip-flop from its input equations. d. Derive the State table. e. Derive the State Graph. Determine the state sequence and output sequence if the initial state is So and the input sequence is X= 01100 B B KA CK JA KB CK to Clock Clock X" X- X' A B'
Below is the case for a sequential circuit with 3 states, 1 input and 1 output diagram is given. Draw the state chart and design the circuit using one-hot coding with D flip flops.
Question: The flip-flops in the drawing below are positive edge triggered D flip-flops. Let Q2, Q1, QO = 0,0,0 initially. a) Plot the clock, Q2, Q1 and QO until the outputs begin to repeat. b) Show the circuits acts as a counter 00 1000 Hz/50%