Fill in the blanks: A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a compressive load of 0.75 MN as shown in the figure and the stress in the column is limited to 55 MPa, Calculate the desirable wall thickness of the column given that the diameter of the outside wall is 25 cm. Column Base plate

Fill in the blanks: A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a compressive load of 0.75 MN as shown in the figure and the stress in the column is limited to 55 MPa, Calculate the desirable wall thickness of the column given that the diameter of the outside wall is 25 cm. Column Base plate

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.8P: A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure)...

See similar textbooks

Similar questions

a cylindrical disk with diameter 40 mm and thickness 2 mm is compressed stress = applied force/cross sectional area what load was placed on the disk when stress = 500MPa
A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod is 325 kN/mm?, calculate the minimum thickness of the rod. Give your answer in millimetres (mm) and to 2 decimal places.
A round steel bar with a diameter of 1.500 in is subjected to the axial loads shown. P1 = 95 k, P2 = 115 k, P3= 55 k, P4 = (P1-P2+P3) k. If Section 2 has a length, L2 = 65 inches, find the change in length of Section 2. Report the answer below in inches, absolute value, 3 significant digits. P1 Your Answer: 100 inches Round Steel Bar P2 Section 2 12 P3 80 inches P4
A hanger rod is stressed to 0.9167 N/mm2 , when a tensile load of 18 N is acting on it as shown in fig. Find the diameter of the shaft. Hanger rod Walk away 18 N support beam Free body diagram of hanger rod
3. A mild steel rod supports a tensile load of 50 kN. If the stress in the rod is limited to 100 MPa, find the size of the rod when the cross-section is 1. circular, 2. square, and 3. rectangular with width = 3 × thickness.
Bar (1) in Figure PP1.2-6 has a cross-sectional area of 0.75 in.². If the stress in bar (1) must be limited to 30 ksi, determine the maximum load P that may be supported by the structure. Answer in kips rounded-off to 2 decimal n 6 ft B (1) Figure PP1.2-6 4 ft 5 OF 6 QUESTIONS REMAI
A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a compressive load of 0.75 MN as shown in the figure and the stress in the column is limited to 55 MPa, Calculate the desirable wall thickness of the column given that the diameter of the outside wall is 25 cm. Column ANS: Base plate mm (one decimal place)
1. Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive load of 250 kN. The section dimensions are breadth, b = 0.12 m, depth, d = 0.05 m with an equal thickness on all sides, t = 0.003 m. Calculate the compressive stress σ in the tube. Give your answer in N/mm2 to 2 decimal places.
2. Figure (a) shows the cross section of a column that uses a structural shape known as W8 x 67 (wide-flange beam, nominally 8 in. deep, weighing 67 Ib/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7 in², Ix =272 in“, and ly =88.6 in4. Figure (b) shows the cross-sectional dimensions for the structural steel section known as C10 x 20 (channel with a nominal depth of 10 in., weighing 20 Ib/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88 in?, Ix =78.9 inª, and ly =2.81 in*. If a W8 x 67 section is joined to a C10 × 20 section to form a structural member that has the cross section shown in Figure (c), a. Locate the centroid of the built-up section in the Figure (c). b. Calculate the centroidal moments of inertia, Ix and ly for this cross section. 事士 0.606 in. 0.933 in. y Web in. --0.575 in. 10 in. - Flange -- 0.379in.…
The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the design of AC only, if the allowable stress for the steel in this application is = 160 MPa, and the diameter of AC: d = 22 mm. Calculate the largest load p on AB in order to keep AC safe: pmax = ____ kN/m. Calculate your answer to 1 decimal place.
A thick cylinder has an outside diameter of 100 mm and an inside diameter of 60 mm. It is pressurized until internally until the outer layer has circumferential stress of 300 MPa. Calculate the pressure difference between the inside and outside. (Note: Please insert your answer with at least one decimal place. (the answer is in MegaPascal, MPa)
The following figure shows the critical position of a crane that supports 2.5 Tons of load by means of a chain. You are delegated the responsibility of building a crane with similar geometric characteristics and load capacity. The diagram of free body of the crane arm can be redrawn as follows. (check the attached image "fbd") Assuming that the crane arm will be made of steel with yield stress sigmaY =220 MPa and that you must consider a safety factor of F.S.=1.5, propose a profile from the following catalog for the manufacture of the crane arm. Ignore the effects of shear forces on this element. On the other hand, it is very important that you consider the effects of axial loads. Commercial profiles for arm construction. (Check image "profiles")