Figure shows a composite beam having a symmetry trapezium cross-section compromised of steel and brass being subjected to bending moment. Using the data given in Table, and factor of safety of 3.5, determine the largest bending moment M which can be applied to the composite beam when it is being bent about x-a

Figure shows a composite beam having a symmetry trapezium cross-section compromised of steel and brass being subjected to bending moment. Using the data given in Table, and factor of safety of 3.5, determine the largest bending moment M which can be applied to the composite beam when it is being bent about x-a

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with “full" details II-Obtain the Principal Stresses, the Maximum Shear Stress, and complete the table below III- Draw the Planes of Principal and Maximum Shear Stresses in the space provided below Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw > S y Ox =10 Ksi Тух 5 Ksi 10 5 -20 -15 -10 5 10 15 20 5 10 Tccw > S' O Avg. TMax. 01 02 Op1
TDe tuláaiceicilaal, D. ile e 200e ticioddocidcICIdCies he sim Ang 2. Fin sile wrl imd tlaeide hrety- 5. JAns. 3 mm) 3. Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pressure of 0.7 N/mm2. Take JAns. 6.25 mm] maximum tensile stress for cast iron as 14 MPa. fIm and is to be subiected to an internal pressure of 2.75
P= 200 lbs |=2" T 250 in-Ibs Qt. DRAW STRESS STATES いITH A SQLARE ECEMENT エN xY AXES Label with stress values Q2 DRAW MOHR'S CIRCLE AT A Q3.CALCULATE PRINCIPAL STRESSES AND DRAW THE PLANE FoR ri$ a IN THE SCHEHATIC Draw element rotated to principal planes and label with stress values and rotation angle
Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is 47,500N.
Consider the plane stress element shown in representing the state of stress at a material point. If the magnitudes of the stresses are such that ox 210 Pa, oy = 110 Pa, and = - Txy = 70 Pa, calculate the magnitudes of principal stresses oj and 02, and the maximum shear stress, Tmax, generated at %3D this material point. (a) Record here the the positive of the two principle stresses. (b) Record here the the negative of the two principle stresses. (c) Record here the the maximum shear stress. Tyz Oy
The state of stress at a point under plane stress 40 MPa, Oyy condition is Ox = = 100 MPa and Txy 40 MPa. This radius the Mohr's circle representing the given state of stress in MPa is:
200 mm diameter rod is subjected to loads as shown. Determine the state of stress at points A and B. Show your results on an infinitesimally small square plane (please use the ones drawn below, which helps you in directions). 8 m 600 N 10 m 400 N 700 N + Oz Tyz + Txy Ox Oy A