Figure shown below is a gate in the form of circular arc with a central angle of 60° and radius 2m with one end resting on the crest of the dam. The water surface is flushed with the upper end of the gate. Determine the location of the horizontal component from point O. The gate is 4.02 m long normal to the plane of the paper. 0 2m 60 ⁰

Figure shown below is a gate in the form of circular arc with a central angle of 60° and radius 2m with one end resting on the crest of the dam. The water surface is flushed with the upper end of the gate. Determine the location of the horizontal component from point O. The gate is 4.02 m long normal to the plane of the paper. 0 2m 60 ⁰

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3) Water is pumped from a reservoir to a packed tower at a volumetric flow rate of0.02 m³/s. Water enters the packed tower from the bottom and exits from the topas given in the figure and the top of the tower is open to the atmosphere. Thepipeline consists of 50 m of 3-inch schedule 40 commercial steel pipe, which includes90° elbows and two fully open gate valves. The diameter and the height of the packingin the tower are 0.8 m and 3 m, respectively. The packing material consists ofspherical ceramics material with a diameter of 2.0 cm and a specific gravity of 2.5.The void fraction of the packed bed is 0.4.a) Determine the pressure drop in the packed bed.b) Calculate the total friction loss between point "1" to point "2".Pwater = 998 kg/m³Hwater = 1x10³ kg/m.s0.8 m3 mH₂O Skip question.
The cantilever beam is loaded as shown in Figure Q2 (b). Use method of moment area to determine slope at point B and deflection at point C. Take EI as constant.
Home Work Water flows through the pipe at A at 300 kg/s, and then out the double wye with an average velocity of 3 m/s through B and an average velocity of 2 m/s through C. Determine the average velocity at which it flows through D. 250 mm 350 mm 150 mm 250 mm
Air RD -0.75 Q3-A reducer bend having an outlet diameter of 15 cm discharges freely. The bend, connected to a pipe of 20 cm diameter, has a deflection of 667 and lies a horizontal plane. Determine the magnitude and direction of force on the anchor block supporting the pipe when a discharge of 03 m²/s passes through the pipe
A 50 mm nozzle is attached to a 350 mm pipe by flange bolts. What will be the total force in the bolts when the pressure at the base of the nozzle is 450 kPa? Assume C = Cv 0.92. %3D O 41.56 kN O 41.83 kN O 43.30 kN 39.84 kN
Tank filles with water as shown in fig. fing the hevi Zental and vertical hydrostatic Force on the Part CD, BC . AB. use The informution :- Cylinder radiug R= 0,5m %3D Reading of 5=1S KPa The hidh CH) = 3.5 m %3D The width of the ey linder = ym G Tank Full of Water Width = b H R
01) For the composite channel shown in Fig. The bed slope is (0.0003). Calculate: 1- The discharge of the channel 2- The required freeboard n-0.028 n-0.035 n-0,025 2.7m I.Im 1.5 6m 5m
w kH fm 2.0m PIN 15KNM 15 KN•m 2.0m RAX=24 KN 15KNM C 2- Rothe Find the value of w 4m Rc Ray 8m
... 5m water gate Mercury (SG = 13.6) %3D Shown is a 60cm square gate in the side of the tank containing mercury and water. The interface surface of the mercury is exactly at the middle of the gate as shown. Find the magnitude of the total hydrostatic force acting on the gate. (A) 21.05 KN B 19.46 KN 23.58 KN D 26.82 KN E) No answer among the choices
ANVAS Student Portal B2308-57 R Knowing Question Bank - Friction Two concrete blocks weighing 1800N each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown? 300 mm - 540 mm A=05 540 Plastic mm liner 6 N/mm Technology Drun 14=1.0- a) Will the upper block be in equilibrium? Yes or No? Yes b) Provide F/N of the upper block [ Select ] c) Will both blocks be in equilibrium? Yes or No? Yes d) Provide F/N of the lower block [Select ] AH F5 F6 F7 PriSc F8 F9 F10 F11 F12
62. Water is flowing at a rate of 12 cm³/s into a conical vessel 18 cm deep and 10 cm across the top. When the water level is h meters deep, the water level is rising at a rate of 3 cm/s. Find the value of h. a. opavise 3. 4.73 cm b. 4.06 cm stw 000,05 c. 4.60 cm d. 4.37 cm
The degree of indeterminacy for the structure is given as 24 kN w = 12 kN/m E5 m B 10 m to 3A m O a. Four O b. Zero O c. Five O d. Three