Figure 4.46 shows a water tank with a circular tube connected at its bottom. A circular door seals the pipe opening to prevent flow. In order to drain the tank, a winch is used to hold the door open. Calculate the amount of force the winch cable must exert to open the door. Winch Cable Water 38 in 30 -Hinge Open pipe

Figure 4.46 shows a water tank with a circular tube connected at its bottom. A circular door seals the pipe opening to prevent flow. In order to drain the tank, a winch is used to hold the door open. Calculate the amount of force the winch cable must exert to open the door. Winch Cable Water 38 in 30 -Hinge Open pipe

Name: Figure 4.46 shows a water tank with a circular tubeconnected at its b
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Figure 4.46 shows a water tank with a circular tubeconnected at its bottom. A circular door seals thepipe opening to prevent flow. In order to drain thetank, a winch is used to hold the door open.Calculate the amount of force the winch cable mustexe

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2- A (0.14 m/s) oil has (density 880 kg/m & viscosity 0.026 pa.s) is pumping from first tank to second tank by using centrifugal pump and discharge pipeline 14 inch in diameter. If the pipe roughness is 0.045mm: 1- Calculate pipe frictional head loss for discharge pipe 6100m in length. 2- Calculate pump liquid power if oil level in first tank 7 m, the oil level in second tank is 14 m, and the suction pipe length is 55 m and diameter is 16 inch.
The load carrying crane shown in the figurethe drum with its rope wound with one hydromotorare driven. Object A is slanted as the rope hugsIt moves up and down over the sled.The diameter of the drum on which the rope is wound is 300 mm.All hydraulic system until hydromotor30% of pressure losses in the components (efficiency 0.7)It will be taken. Thread of hydraulic gear pump in one round0.8 lt of oil dispensed from the cavitiesSince it isa. Calculate the flow of the pump (lt / min)b. Find the working pressure of the pump (bar)Load speed v = 0.6 m / sTensile force on the rope T = 10,000 NIt will be taken.
6. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a flow rate of 6 L s'. For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of the water gage. Determine the smallest standard commercial steel pipe that will give the required performance. pump 4.5 m. 1.8 19=d 3.5 m 7. water 90° elbow
Q2- A (0.14 m/s) oil has (density 880 kg/m³ & viscosity 0.026 pa.s) is pumping from first tank to second tank by using centrifugal pump and discharge pipeline 12 inch in diameter. If the pipe roughness is 0.045mm: 1- Calculate pipe frictional head loss for discharge pipe 6100m in length. 2- Calculate pump liquid power if oil level in first tank 7 m, the oil level in second tank is 14 m, and the suction pipe length is 53 m and diameter is 14 inch.
Show complete solution and formulas used. Show the schematic diagram too. Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min water from a closed tank, where the pressure (above the water level) is p = 40kPa. The equivalent length of the smoothened concrete pipe on the suction side is 12m while the suction flange of the pump is 8m below the water level. The vapour pressure at the given water temperature is 2.8kPa. The required net positive suction head is NPSHr = 3.2m.
Q2' A pipe with a radius of 15 mm is attached to a garden hose with a nozzle. If the velocity of flow in the pipe is 4 m/s, what is the velocity of the flow at the nozle when it is adjusted to have a diameter of 16 millimeters, and what is the flow rate?
Problem 5- Two reservoirs are connected by 198ft of 2-in diameter tubing. What is the flow rate when the difference in elevation is 50ft? (v= .001 ft²/s)
Centrifugal pump has differential pressure 15 bar and use to transport oil between two separators. If the pressure at first separator is 4 bar calculate the pressure at second separator and NPSH. Where: Suction and discharge pipe diameters = 10 inch, Suction pipe length = 16 m, ld Oil level at first separator 3 m2d Oil density=880 kg/m³ P Oil flow rate=0.092 m³/sec e Pipe roughness= 0.045 mm Discharge pipe length = 25 m O Oil level at second separator = 5.5 m2d Oil viscosity = 9.5 x 10³ Pa.s Oil vapor pressure 22.5 kPa d кра 4.5x10²
The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow the suggested design procedure and select a suitable pipe size and pump for the system. A B A: Globe valves (2 of them) B: Union fittings (4 with 2 not shown) C: Plate welded to tank to suppress air entrainment in pump inlet D: Elbows: there are five 90° elbows and two 45° elbows The pipe is all wrought iron, with threaded fittings, schedule 40. Pipe lengths total 35.36 m. Total inlet pipe length from tank to pump is 1.22 m. z1 = 1.22 m and z2 = 3.66 m.
Q1) Using a system similar to that shown in figure, if air pressure p = 50 kPa., and the depth h1 = 0.3 m, compute the water flow from side nozzle of diameter (d = 10 mm) and the rise h₂ from that nozzle. vesn Air pressure It, 11₂ Nozzle
1. An 80 mm schedule 40 steel pipe is 1800 m long and carries a lubricating oil between 2 points A and B such that the Reynolds number is 1200. Point B is 10 m higher than point A. The oil has a specific gravity of 0.85 and dynamic viscosity of 6.51 X 10-1 Pa.s. If the pressure at A is 345 KPa, calculate the pressure @ B. 2. Determine the energy loss for a sudden contraction from a 4 in schedule 80 steel pipe to a 1.5 in schedule 80 pipe for a flow rate of 250 gal/min. 3. Determine the equivalent length in meters of pipe of a quarter open gate valve placed in a DN 250 schedule 40 pipe.
Water is pumped through a vertical 2-in. new galvanized-iron pipe to an elevated tank on the roof of a building. The pressure on the discharge side of the pump is 200 lb per sq in. What pressure can be expected at a point in the pipe 250 ft above the pump when the flow is 150 gpm? Answer should be: 37 lb per sq. inch Show your handwritten solution, thank you.