Figure: 1. In the figure shown, a vertical triangular gate submerged in a certain liquid with s.g. = 0,85. If the eccentricity is 150 mm determine the distance between the top of the gate and the liquid surface, L.S. L.S. d. 1.2 m 2. In Prob. 1, determine the magnitude and location of the hydrostatic force on the gate. 2.7 m

Figure: 1. In the figure shown, a vertical triangular gate submerged in a certain liquid with s.g. = 0,85. If the eccentricity is 150 mm determine the distance between the top of the gate and the liquid surface, L.S. L.S. d. 1.2 m 2. In Prob. 1, determine the magnitude and location of the hydrostatic force on the gate. 2.7 m

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

The cross-sectional area of each clamp forming a fixed-supported cage system from points C and D shown in the figure below is 300 mm² and a modulus of elasticity is 105 GPa. A single force P-90 KN acts on the Kafcs system from point A as shown in the figure. Determine the vertical displacement at point A using the work-energy method. 2 m B P 1.5m
A rectangular gate 6 ft tall and 5 ft wide in the side of an open tank is held in place by the force F as indicated in the figure. The weight of the gate is negligible, and the hinge at O is frictionless. (a) Determine the water depth, h, if the resultant hydrostatic force of the water acts 2.5 ft above the bottom of the gate, i.e., it is collinear with the applied force F. (b) For the depth of part (a), determine the magnitude of the resultant hydrostatic force. (c) Determine the force that the hinge puts on the gate under the above conditions. Hinge O Gate F 2.5 ft 6 ft Water
2.12. Find hydrostatic force on the conical body shown in figure below. (H =2.7m, L₁ L2=0.6m, R=0.9m) H₂O H L₁ L2 R
A Pitot tube having a coefficient of Cy =0.98 is used to measure the velocity of water at the center of a pipe. The stagnation pressure head is 5.67 m and the static pressure head in the pipe is 4.73 m. What is the velocity? %3D
Two beads are sliding freely on a horizontal rod. Use the following conditions. mA = 3 kg m₂ = 1 kg e=0.9 VA = 1 m/s Va = -3 m/s a. Determine the final velocity of both beads. b. Determine the average interaction force, F between the beads if the duration of the impact is 0.005 seconds Vg m ma
The 12 kN crate is being pulled by the force P as shown in the figure. The force P makes an angle of e with the horizontal. a) Find the smallest possible force P to cause the crate to slide. b) Determine the angle e. c) Determine the horizontal frictional force acting at the bottom of the crate, W=12KN Note : The total surface R I Pmin - M= 0.20
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E 200, 000M Pa and %3D a = 11.7- Neglect bending of the beam. A=640mm2 A=320mm2 A C 1.2 m 0.8 m 1.2 m V 54KN 1. If there is no change in temperature, what is the deformation of rod C in mm? 2. If there is no change in temperature, what is the deformation of rod B in mm? 3. What is the stress of rod C if there is no change in temperature in MPa? 4. What is the vertical displacement of D in mm, if the temperature rises 50°C? 5. If the temperature rises, what is the thermal deformation of steel in mm?
Topic: Hydrostatics A rectangular plane, 1.2 m by 1.8 m is submerged in water and makes an angle of 30 degrees with the horizontal, the 1.2 m sides being horizontal. 1. If the top of the edge of the plane is at the free surface, what would be the shape of the pressure distribution acting on the plane. 2. What is the minimum AND maximum pressure acting on the plane in kPa? 3. Find the magnitude of the hydrostatic force acting on either side of the plane in KN. Draw a figure with labeled pressure prism diagrams.
The 1-m diameter sphere in the figure shown rests in static equilibrium against a frictioniess wallat B. Compute the speciic gravity of the sphere. 0.5m Water
16. A cylindrical pressure vessel has an inner diameter of 4 ft and a thickness of 1/2 inch. Determine the maximum internal pressure it can sustin so that neither its circumferential for its longitudinal stress component exceeds 20 ksi. 0.417 D. 833ps B. 1666 3 A. 200 psi
5. Compute the magnitude of the resultant force on the indicated area and the location of the centre of pressure as shown in Figure 5. Show the resultant force on its location. 0.80 m 0.5 m Semicircular hatch 1.50-m diameter Turpentine sg =0,88 70 Figure 5: A Tank
5.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the vertical component of the hydrostatic force on the submerged curved section of the gate. Use unit weight of water 9.80 kN/m^3. fluid mechanics