9 Fig 13.8 shows a Warren girder consisting of seven members each of 3 mlength freely supported at its end points.2 kN4 kNBA60°60 60°60 DE6 mFig. 13.8.The truss is simply supported at Point A and D,Match each item to a choice:Determine the forcein member BCMember CDChoices:: 1.732KN (OC): 3.5kN (T): 1.444KN (T): OKN: 4.042kN (C): 0.577KN (C)

Given data: The load on point B is PB = 2 kN. The load on point C is PC = 4 kN. The distance…

Fig 13.8 shows a Warren girder consisting of seven members each of 3 m length freely supported at its end points. 2 kN 4 kN B 60 60 60 60 6 m Fig. 13.8. The truss is simply supported at Point A and D, Match each item to a choice: Determine the force in member BC Member CD Choices: : 1.732KN (C) : 3.5kN (T) : 1.444KN (T) : OKN : 4.042kN (C) : 0.577KN (C)

Fig 13.8 shows a Warren girder consisting of seven members each of 3 m length freely supported at its end points. 2 kN 4 kN B 60 60 60 60 6 m Fig. 13.8. The truss is simply supported at Point A and D, Match each item to a choice: Determine the force in member BC Member CD Choices: : 1.732KN (C) : 3.5kN (T) : 1.444KN (T) : OKN : 4.042kN (C) : 0.577KN (C)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(2) For the truss loaded and supported As shown, use the Method of Sections to compute the ff: 0.9 kips 1.8 kips 1.S kips 0.9 kips 9ft Member Force(kips T/C -12 ft--14 ft→f-14 ft – AB AG GF Note : 1 kip = 1000 lb (but answer in kips) 31.5 ft L. 8ft
2. Determine the forces in members BD, BE, CE and DE in the truss shown below using method of section where in the units are in kips (1 kip=1000 lb) H B 36' 35' 32' 27' C E G 30* 30K 30* 30* 30* 30* 30* 8 panels @ 25' = 200' %3D
Consider the roof truss shown below. If each chord (i.e. AG, AE, EG) is a steel tube with a diameter of 356 mm and wall thickness of 14.70 mm and each web member (i.e. internal members i.e. BF,CF, CG, CH & DH) is a rectangular timber section of 291 mm x 212 mm, determine the weight of member CE. Assume Psteel = 7850 kg/m3, Pwood = 850 kg/m³. 2.50 m 36.9 Your Answer: Answer 3 B 2.50 m units 48.2 H C D E
a) Draw the FBD of the entire truss and use this diagram to determine the reaction forces at the supports. Note the truss is supported by a roller at E Using the Method of Sections, determine the forces in member a) BC (5 b) HC c) HG Show the FBD of the truss after the cut is performed. State whether the members are in tension or compression. 5m Figure 2 B 4 m H 30 kN 5 m G 60 kN 5 m D F 30 kN 5 m E
Question 5 Find the supportive force system for the cantilever beam shown pinned at C. Given data: Point load, Not yet answered P=380 N and distributed load, w=80 N/m. Marked out of 5.00 on 7 m 2 m A 5 m- 5 m- Supportive force system Ax= Ay= Сх- N Су- By= N
EXTRA CREDIT PROBLEM 6.6 Using the method of joints, determine the force in each member of the truss shown. State whether each member is in tension (T) or compression (C) (+) = Tension / (-) = Compression 4.5 m 4.5 m D 2.8 m C 8.4 kN 8.4 kN A Question 28 ( FBC in kN Your Answer: Answer A Question 29/ 4 FBD in KN Your Answer: Answer Retake question Retake question
The fabricated steel members are being assembled into a truss on-site in the municipality of Alfonso, Cavite. The assembly started at the elevated ground at both sides and is to meet at the midspan. Nearing to the end of construction, it was found that the last member, CD, was fabricated too short by A D= 4.450 mm. The engineer then came up with an idea of applying a force P at joints C and D as shown to close the gap. P. с c' P 3 m -3 m- -3 m- 3 m- Use E = 200 GPa and cross-sectional area of members BC, DE, CD each 4500 mm2 while AC and DF being 6363.961 mm2 a) Determine the necessary force, P, to close the gap in kN. wwww b) If force P will then be removed after being assembled, calculate the force in CD in kN.
The connected pipes are attached to the wall with a fixed support; i.e. built in. Calculate the reaction forces due to the loading shown. FBD required, can be more sketch like, but must have all reactions drawn and labeled.The 150 N force is parallel to the z axis; −150 k', the 200 N force is parallel to the y axis; 200 j,̂I will assume that all of the moment support reactions(curved arrows) are drawn positive.
2 1b 120 For the shown truss, the force in member FG equals You should scan your calculation shet for thin.tn OA 5.86 k (C) OB 8.87 k (C) OC7.67 k (C) OD.6.37 k (C) O E. 4.04 k (C)
NOTE. This is a multi-part question. Once an answer is submitted, you will be unable to return to this part Consider the given structure with P-490 lb. 9 ft 9 ft P -7.5 ft- C B Using the method of joints, determine the force in each member of the truss shown. State whether each member is in tension (7) or compression (C) The force in member FAB IS 343 ID The force in member FACIS 12.99 Ob TO The force in member Facis 15 Olb T The force In member FBE IS The force in member FCD Is The force in member FCE IS 8,66 Olb T O The force in member FDE IS 15 lb C 7.5 lb с 8 3 7.5 lb C ( › T O 3
Pleass explain step by step every detail and help me solve. We should do a free body diagram for D,G,C, A, and B. 12.5kN 4 2.5m 34 2m 12.5kN B 2 m Plan: 1. 2. 3. 4. 12.5kN 2 m 12.5kN D Given: Loads as shown on the truss Find: Determine the force in all the truss members (do not forget to mention whether they are in T or C). Check if there are any zero-force members. Find external support reactions (if necessary) Draw FBD pints Apply E of E.
I/B For truss shown :Answer the following P. E K Lläi 4 FDI and FIE are equall to zero Yes O No