Experiment DataTake the following data for the syringe injection pumpInner diameter of syringe barrel: D = 1.5 cmInner diameter of the needle shaft of the syringe: d = 0.5 mmThe thread pitch of lead screw: pt 0.75 mmLead screw rotation velocity (rpm): nCalculationsLiquid injection rate (cm /hr) Q = pt *n * 60 * n * D²/4Velocity of liquid in syringe barrel (cm/min) v = 4Q/ (60 * T * D?)%3DVelocity of liquid in syringe needle (cm/min) vn = 4Q/ (60 * n * d?)%3DFind the rotation velocity of lead screw n and the velocity of liquid in syringe needle if therequired injection dose is1. 10 cm3 in 3 hours(continuous injection)2. 20 cm3 in 12 hours(discontinuous injection, 5 cm³each 3 hour, injection time = 1min).Discus the results briefly.

Rotational velocity is the velocity of the object which is rotating about the axis divided by time.…

Experiment Data Take the following data for the syringe injection pump Inner diameter of syringe barrel: D = 1.5 cm Inner diameter of the needle shaft of the syringe: d = 0.5 mm The thread pitch of lead screw: pt 0.75 mm Lead screw rotation velocity (rpm): n Calculations Liquid injection rate (cm/hr) Q = pt * n * 60 * n * D²/4 Velocity of liquid in syringe barrel (cm/min) vb = 4Q/ (60 * n * D?) %3D Velocity of liquid in syringe needle (cm/min) vn = 4Q/ (60 * n * d?) %3D Find the rotation velocity of lead screw n and the velocity of liquid in syringe needle if the required injection dose is 1. 10 cm3 in 3 hours (continuous injection) (discontinuous injection, 5 cm³ each 3 hour, injection time = 1 2. 20 cm3 in 12 hours min).

Experiment Data Take the following data for the syringe injection pump Inner diameter of syringe barrel: D = 1.5 cm Inner diameter of the needle shaft of the syringe: d = 0.5 mm The thread pitch of lead screw: pt 0.75 mm Lead screw rotation velocity (rpm): n Calculations Liquid injection rate (cm/hr) Q = pt * n * 60 * n * D²/4 Velocity of liquid in syringe barrel (cm/min) vb = 4Q/ (60 * n * D?) %3D Velocity of liquid in syringe needle (cm/min) vn = 4Q/ (60 * n * d?) %3D Find the rotation velocity of lead screw n and the velocity of liquid in syringe needle if the required injection dose is 1. 10 cm3 in 3 hours (continuous injection) (discontinuous injection, 5 cm³ each 3 hour, injection time = 1 2. 20 cm3 in 12 hours min).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. For Pump Omicron, the pump performance data is shown in Table 2 below. Plot a curve of best fit Havailable versus Q from 0 Lpm to 30 Lpm. State the equation represented by the curve. On the same graph, plot the Hrequired versus Q and indicate the operating point. Table 2: Pump Omicron performance data Q (LPM) H (m) 0 46.5 46 42 37 29 16.5 0.0 5 10 15 20 25 30
PLEASE ANSWER THEM ALL FOR AN UPVOTE. THANK YOU. Given: Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Ans. the ff questions. •What is the pressure in MKS unit? •What is the pressure in CGS unit? •What is the viscosity of the liquid? • If the weight was given as 8.5 grams, what will be the density of the liquid? •What is the kinematic viscosity of the liquid? •What is the fluidity of the liquid?
Reynolds number for pipe flow may be expressed as Re = (4 m/ Trd) / µ Where m = mass flow, kg/s d= pipe diameter, m p = viscosity, k/m s In a certain system, the flow rate is 5.448 kg/min +0.5 %, through a 0.5" (inch) diameter (±0.005"). The viscosity is 1.92x 10-5 kg/m s, ±1 %. Calculate the value of the Reynolds Number and its uncertainty. Determine the main contribution to uncertainity.
w. An optimally aligned wind turbine is subject to constant wind speed of 12 m/s, explain how the turbine power output could be varied. vi. With reference to the following formula: explain its function, and its constituent parameters. PM (Um) = √p(u). W(u)du
METERS | FEET MODEL: IA6BJM SIZE: 8" x 6" x 13" RPM: 1750 76+250 PRESSURE MAX: 120 PSI GRAPHIC 61+200 FØ13," (75 HP) SCALE 70% 75% 80% 82% 60 GPM Ø12%" (60 HP) 83% 84% 83% 46-150 82% 80% Ø12%" (50 HP) 75% 011%" (40 HP) 70% 65% 31+100 100 BHP Ø10%" (30 HP) NPSHr ftm 75 BHP 60 BHP 30+9 15+50 50 BHP 30 BHP 40 BHP 20+6 NPSH. 10+3 GALLONS PER MINUTE LITERS PER MINUTE Refer to the system curve drawn on this pump curve. If the pump is to move 1200 gpm, what is the expected system total dynamic head (ft)? 1136+300 2271+600 00620 4543+120아 5678+1500- 6414+1800 7949+2100- 9085+2400 * 11356+3000 10 FEET
The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston displacement is 0.049m3/sec, what is the operating speed of the compressor? complete soln tnx.
No. Date Determination of Discharge Thru a-Siphon- Vol tormata- (N1)2 PI +71;[V2)? P2 十名2 h= 63.5 cm trial #1 trial #2 trial #3 t= 75 V= 340 ml t- 10s V = 490 mL V: 250mL %3D complete timel3] ' Volume (mL) the table below Ishow calculation pleasc) Actual Discharge (1s) treal #(m) Theorehical Discharge Difterence
As a mechanical engineer, you were asked by your supervisor to monitor the operation of 4-stroke engine; as a result you got the following readings: > Imep = 780 kN/ m2 > Engine speed = 800 rpm > Brake Power 30 kW %3D %3D > nm = 85 % > B/S 0.7 You noticed also, that the inlet valve opens 10° before TDC and closes40° after BDC and it takes 0.0035 second after ignition for the charge to gain maximum pressure. Depending on the above readings, find the following engine parameters: a. The crank angle when the spark occursfor the maximum pressure to be at TDC b. The time period in second of inlet valve opening during one cycle c. The diameter of the engine d. The average piston speed 1 Upload file
A four-stroke SI engine 0.08 m bore (d), 0.10 m stroke (L), is tested at full throttle at constant speed. The fuel supply is fixed at 0.0011333 kg/s and the spark plugs of the four cylinders are successively short circuited without change of speed, brake torque being correspondingly adjusted. The brake power (bp) measurements are the following:With all cylinders firing = 12.5 kWWith cylinder No. 1 cut off = 9 kWWith cylinder No. 2 cut off = 9.15 kWWith cylinder No. 3 cut off = 9.2 kWWith cylinder No. 2 cut off = 9.1 kWThe lower calorific (or heating value, LCVf) of the fuel is 44100 kJ/kg. The clearancevolume (Vcl) of one cylinder 70.0 x 103 mm3. Determine:(a) Indicated power (ip) of the engine under these conditions.(b) The indicated thermal efficiency (c) The relative efficiency of this engine.
PROCESS INSTRUMENTATION AND CONTROL In a differential pressure flow meter, determine the velocity at the outlet for the given technical specification. The density of the liquid flowing through the pipeline is 997 kg/m³, Pressure at inlet is 10 lb/ft2, pressure at outlet is 8 lb/ft2 and cross sectional area of the orifice is 0.2512 m. Note: Ratio of meter diameter to pipe diameter is 0.5 and discharge coefficient is 0.61. Also, find the flow rate.
Q: Experiment of venturi meter. Please give a brief description for Bernoulli’s equation. What typeof parameters can be derived from an experiment?
A four-stroke SI engine 0.08 m bore (d), 0.10 m stroke (L), is tested at full throttle at constant speed. The fuel supply is fixed at 0.0011333 kg/s and the spark plugs of the four cylinders are successively short circuited without change of speed, brake torque being correspondingly adjusted. The brake power (bp) measurements are the following:With all cylinders firing = 12.5 kWWith cylinder No. 1 cut off = 9 kWWith cylinder No. 2 cut off = 9.15 kWWith cylinder No. 3 cut off = 9.2 kWWith cylinder No. 2 cut off = 9.1 kWThe lower calorific (or heating value, LCVf) of the fuel is 44100 kJ/kg. The clearancevolume (Vcl) of one cylinder 70.0 x 103 mm3. Determine:(a) Indicated power (ip) of the engine under these conditions.(b) The indicated thermal efficiency (c) The relative efficiency of this engine. (d) Draw schametic diagram