3) The reserve capacity of the plant4) Plant use factor EX: A generation station of 10MW supplied two regions (A and B) which havethe following demands:Region ADemand (kW)600FromТо9 ammidnight12 noon25009 am8005 pm6 pm7 pmmidnight12 noon50005 pm6 pm7 pmNo-load4000Region BDemand (kW)800FromТо8 am1 pm2 pm5 pmmidnightmidnight8 am50008001 pm2 pm5 pm5000800

Answered: Image /qna-images/answer/185aab65-90ad-4a0c-978f-f55038545dd1.jpg

EX: A generation station of 10MW supplied two regions (A and B) which have the following demands: Region A То Demand (kW) From 600 midnight 9 am 9 am 12 noon 2500 800 5 pm 6 pm 7 pm midnight 12 noon 5000 5 pm 6 pm 7 pm No-load 4000 Region B Demand (kW) 800 From То 8 am midnight 8 am 1 pm 2 pm 5 pm 5000 1 pm 2 pm 5 pm midnight 800 5000 800

EX: A generation station of 10MW supplied two regions (A and B) which have the following demands: Region A То Demand (kW) From 600 midnight 9 am 9 am 12 noon 2500 800 5 pm 6 pm 7 pm midnight 12 noon 5000 5 pm 6 pm 7 pm No-load 4000 Region B Demand (kW) 800 From То 8 am midnight 8 am 1 pm 2 pm 5 pm 5000 1 pm 2 pm 5 pm midnight 800 5000 800

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The total power drawn by the two-impedance load in parallel is 26kW at 0.98 power factor lagging, it is being supplied by a 230-volts AC source. One of the loads (Load 1) takes 16kVA at 0.77 power factor lagging. What is the reactive power of the unknown impedance (Load 2)?
Q2. For the circuit shown below, sketch the current waveforms iş and io and determine the Average and RMS for both currents. a = 50° TI 50 2 Vs = 300 sin 100zt ( cot T2 in cot
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The output voltage waveform of a four quadrant chopper is shown in figure. In the waveform, Vdc is input voltage, D is duty cycle ratio and T is cycle time. DT T. The RMS value of ripple component in output voltage is (A) Vác 2V VD-D (В) V(2D-1) (C) de de (D) V de VD- D? yd
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
A single-phase AC voltage controller has a resistive load R = 10 Ohm, and the RMS input voltage is Vs = 230 V, 60 Hz. The delay angle is 120 degree. Then power factor of the circuit is: Select one: O a. 1 O b. 0.75 O c. 0.44 O d. None of the above O e. 0.9
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
2.14 The current waveforms of la capocitov are avesage peak cursend *atings of 1, =500 A of shown in Fiquse Determine square (rms), and capacitor. Assume, The root mean half sine -wave t = loo us -300 AS t3 Soo Ns f, -250HZ T2 200
Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415220° V with frequency 50 Hz. Based on this information: 5Ω 100mH : 15 2 Load 1 Load 2 i) Calculate the total load impedance. Vs ii) Calculate the current, I. Figure Q2. Write the waveform expressions in frequency domain for Vs and I. Draw a phasor diagram consists of Vs and / and state the relationship between Vs and I. (ii) (iv) Determine the power factor and calculate the real power, reactive power and apparent power. Establish the power triangle for the load.
An alternating current varying sinusoidally with a frequency of 50 Hz has anrms value of 20 A.a) Determine the instantaneous value at 0.0025 seconds.b) Determine the instantaneous value, 0.0125 seconds after passingthrough a positive maximum value.c) At what time, measured from a positive maximum value, will theinstantaneous current be 14.14 A?
3. A 12020⁰ Vrms is to supply power to a welder, heater and an induction motor. A welder is a coil of (4+j3) ohm, the induction motor draws 60KW with 0.8 power factor, and the heater is a resistor that draws 15KW power. Find the complex power, real power, reactive power and the total power factor that must be supplied by source. If a capacitor will be used to supply a reactive power in the circuit in order that the net load will have a unity power factor, what reactive power must be supplied by the capacitor? Draw the circuit.
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms