Develop a PIC18F4321 Interrupt based program to measure the power in watt absorbed by a resistor R2 = 60 resistor and input voltage Vs = 5V when the switch S1 is closed in the below figure. Write a C-code to configure INTO to trigger the Interrupt and use the ISR to calculate the power. + IT Vs T IT TO PIC S1 IR2 IR1 R2 R1

Develop a PIC18F4321 Interrupt based program to measure the power in watt absorbed by a resistor R2 = 60 resistor and input voltage Vs = 5V when the switch S1 is closed in the below figure. Write a C-code to configure INTO to trigger the Interrupt and use the ISR to calculate the power. + IT Vs T IT TO PIC S1 IR2 IR1 R2 R1

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Write an AVR C-program that uses external interrupt INT0 and Timer1 output compare interrupt to implement a one-second one-digit stop clock. The stop clock should operate as follows: When the circuit is powered on, it should display “0” continuously. When the push button is pressed, the counter should start counting from “0” – “9” at a rate of one second. When the count reaches “9”, it should reset to “0” and continue counting. If the push button is pressed again (the second time after power-on), the counter should stop at the last digit that was displayed. If the push button is pressed for a third time, the counter should continue counting from the number that was on display.
Assume that an external clock signal is being fed into pin T0CKI. Write a program to useTimer0 in 16-bit mode to count the pulses and display the TMR0H and TMR0L registers onPORTB and PORTD, respectively (be sure to read the low register of the timer first). Startthe count at 0x0000 and stop the count at 0xFFFF+1. Use the MPLAB simulator to verifythe proper operation of the program. You may need to use the Watch window to view thecontents of TMR0H and TRM0L as it may not be obvious using the Logic Analyzer, that thecontents of TRM0H are incrementing
Using timert in CTC mode and interrupts create a 50HZ square wave on pin 5. Use a prescaling of 256 define LedToggle digitalWrite void setup 0 ( pinMode / Disbale global interrupts initialization of control register A initialization of control register B // enable interrupts initialization of the output compare register //Enable global interrupts ISRO LedToggle void loop 0 0 OX0B 55536 OX0A TIMER1 COMPA vect Ox00 TIMER1 OVF vect INPUT Ox01 60536 Ox05 63036 65458 TCNT1 4 40000 sei() 625 TIMSK1 OCR1A 25536 65224 65380 1250 digitalRead 20000 156 45536 64286 21 TCCR1B 64911 312 6. 5000 digitalWrite OXOC OX0D 78 2500 OUTPUT TCCR1A 10000
Write a program that generates TMR0 interrupt signal every 65.5msec. (oscillator frequency is 4MHz) Also handle the interrupt and the interrupt subroutine properly. WDT is a timer, and it has a separate built-in low power oscillator. Its main purpose is to reset the program at overflow. On reset, the program starts from the beginning. Also, by resetting it can wake up a sleeping MC. When a wakeup happens, the program continues from last CLRWDT command. In program WDT can be cleared using CLRWDT command. Pre-Scale Value (PSV) is also applicable to WDT as shown in the datasheet. When PSV is 000 from CLRWDT to overflow WDT takes 18ms. For WDT to work, WDT must be turned on at configurations. When in sleep mode the Micro Processor (MC) stops most of its processes to minimize power consumption. It is important for battery-powered systems. Command SLEEP is to make MC enter Sleep Mode. There are three ways to exit a sleep mode: Manual Reset, External Interrupt Trigger (INTF becomes 1),…
Define a new interrupt (Interrupt number 80H). The interrupt service routine for this interrupt will ask the user to enter 2 numbers A and B(each is between 0 and 9), then it will print one of the following statements: - "A > B" - "A < B" - "A = B" TASM
INTR interrupt is enable if a. TP is set to 1 b. TP is reset to 0 c. IF is set to 1 d. IF is reset to 0
If INTO and INT1 are enabled and EICRA-Oxl then Select one: O a. the falling edge of INTO and the rising edge of INT1 generates an interrupt request Ob the rising edge of INTO and the falling edge of INT1 generates an interrupt request Oc any logic change on INTO and the rising edge of INT1 generates an interrupt request Od the falling edge of INTO and any logic change on INT1 generates an interrupt request
Assume that an external clock signal is being fed into pin T0CKI (RA4). Write a C program touse Timer0 in 8-bit mode to count the pulses and display the state of the TMR0L count onPORTB. Start the count at 0x00 and stop the count at 0xFF+1. Use the MPLAB simulatorto verify the proper operation of the program
Create a program that utilizes the timer interrupt and the pin change interrupt in order to measure the frequency of a periodic signal on Port Pin D4. You can do this by saving and then clearing a counter each time the timer interrupt occurs (at a rate of once per second). Additionally, you can increment the counter by the number of low-to-high and high-to-low transitions on pin D4 with the pin change interrupt. Your main loop should monitor when the timer interrupt goes off, and then write the frequency to the serial port for the user to see. Note: your setup function should call your two initialization functions, and then enable global interrupts in the SREG register
Write a program that generates a TMR0 interrupt signal every 65.5msec. (oscillator frequency is 4MHz) •Also handle the interrupt and the interrupt subroutine properly. Report: It can be written on paper or on a computer (I prefer it to be written on a computer)
To hook and chain a FIQ interrupt method, it must begin at the given offset in the Interrupt Vector Table.
Write an interrupt service procedure to check if the number in AL is even or odd. If the number is odd then bit 0 of BL register should be set to 1, otherwise bit 1 should be set. Include all the necessary commands that should be present in the interrupt service procedure.