Determine the safe uniform live load that the beam can carry on a simple span of "L" meters with the ff. parameters: Given: width of beam, b = 450 mm depth of beam, h = 775 mm clear cover up to center of bars = 65 mm Diameter of bar = 32 mm No. of tension bars 9 f'c = 20.7 MPa fy = 414 MPa SDL (excluding beam wt) 12 kN/m Span of beam, L = 8 m

Determine the safe uniform live load that the beam can carry on a simple span of "L" meters with the ff. parameters: Given: width of beam, b = 450 mm depth of beam, h = 775 mm clear cover up to center of bars = 65 mm Diameter of bar = 32 mm No. of tension bars 9 f'c = 20.7 MPa fy = 414 MPa SDL (excluding beam wt) 12 kN/m Span of beam, L = 8 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

L2. 1/2 max No.4 Use Illustration of problem no. 3. Determine the maximum deflection Smax using double integration if the span is L = 8 ft, the depth of the beam is H = 6 inches, the maximum flexural stress is Omax = 12 ksi, and the beam is made of aluminum with E = 10 x 10³ ksi. P B
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1780 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 230 kip-ft, P = 24 kips, LAB = 5.2 ft, LBc = 7.8 ft. %3D MA A В C LAB LBC
A section is given below. the beam has a span of 4m with Fy = 250 MPa. Compute por the Following: a.) Yield moment capacity of the beam b.) Plastic mo ment eapacity of the beam C.) Shape Factor of the beam 160mm 20 mm 165 80mm Somm gomm (21
A simply-supported T-beam is subjected to two pairs of distributed loads: pair 1 (wD1, wL1)and pair 2 (wD2, wL2). The geometric, material and loading properties are all given on thetable above. bf=1368mm bw=408mm t=248mm fc'=25.2MPa fy=336MPa d=918mm d'=92mm Lbeam=12.2m wD1=42.2kn/m wL1=50.2kn/m wD2=170.2kn/m wL2=193.3kn/m1. Solve for the height of the compression stress block using pair 1. 2. Solve for the theoretical steel area using pair 1. 3. Using Es = 0.004, solve for the theoretical steel area using pair 2. 4. Using Es= 0.005, solve for the theoretical steel area using pair 2.
5. Calculate the design flexural strength of the T-beam shown. Use f'c = 27 MPa and fy = 350 MPa. br= 600 mm 25 mm t= 110 mm 3-22 mm 10 mm stirrup hw= 390 mm 10-25 mm 25 mm 20 mm bw 300 mm
A T-section having a cross section shown has a span of 3.6 m. The location of the neutral axis is located 130 mm from the bottom of the beam. Elastic moment of inertia of the beam 200 mm 40 mm 160 mm 50 mm Wu 3.6 m | = 58.13 x 106 mm4 Fy = 250 MPa %D a. Compute the yield moment capacity of the beam. b. Compute the plastic moment capacity of the beam. c. Compute the shape factor. (S.F. = Z/S)
For the given properties of beam below. Compute the flexural capacity of the beam. b = 380mm d = 430mm d' = 70mm fc' = 30MPA fy = 315MPA As = 5- 36mm As' = 2- 28mm A. USE NSCP 2001, Mu = kN-m B. USE NSCP 2015, Mu = kN-m
From the given figure below, determine the minimum height of the beam if the flexural stress is not to exceed 50kPa. Assume width of beam is 200mm (JN 10 N/m 0- T 3M RA=42N 42N B IM TEMA 12N 75NM 81NM, Im RD=3N EL -3N 0° 78 Nm 3NM V-DIAG M-DIAG
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1720 in.4). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA - 170 kip-ft, P = 30 kips, LAB - 5.7 ft, Lgc = 8.6 ft. P MA A B LAB LBC Answer: (a) VA = in. (b) vB - in.
Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving stress If you know GAI = 28 GN/m² Gst=83 GN1m² GBV = 35 GN/m² Aluminum steel Bronzer Do d=100mm 3m d=75mm 2m 1.5m 1.5 KN.m
Required information Consider the loading condition shown. Assume that the flexural rigidity El of the beam is constant. 21 W B -L/2L/2L/2- The deflection at point B is. 0013 W Using singularity functions, determine the deflection at point B and point D. (Round the final answers to four decimal places.) The deflection at point Dis. -0.0163 wwwwwwwwww………… 1 D x Deflection point at D is wrong
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 x 106 mm*]. For the loading shown, determine the beam deflection vc at point C. Assume P = 69 kN, w = 21 kN/m, LAB = LBc= 3.1 m, LCD = 1.7 m. P |B D LAB LBC LCD mm. Answer: vc=