Determine the % resolution of a 10-bit A/D converter for a given reference voltage of 100 volts.
Q: Assume ß >> 1, VBE(on) = 0.7 volts, all npn junction areas identical, and all pnp junction areas are…
A: The given circuit is as shown below,
Q: Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical…
A: The given bridge rectifier is, The model is practical and Voltage at Transformer's primary,…
Q: An SCR HWR is applied a Sine wave voltage. If its firing angle is 45°, what is the value of the…
A:
Q: Determine the gate trigger current and the anode current when the switch, SWI, is momentarily closed…
A: Fig: Given circuit Given that VGK=0.65VIH=15 mAVAK=0.35V
Q: 16/ Which of the following can be used in amplifier circuits? a. Transistors b. Photodiodes c.…
A:
Q: A 4:1 transformer is connected to a bridge rectifier circuit with a lkn load. What is the peak…
A:
Q: What input voltage is needed in a bridge rectifier circuit to have an output of 10Vp?
A:
Q: D. 5:1 110 V rms alll
A: The solution is given below
Q: 7. A PFC circuit is designed with the following parameters. Vin = 100Vrms, Vout = 400V, Iour=2A.…
A: Question 7 . The correct option is A 11.3 A
Q: Clipper circuit: Vi (p-p)= 10 volt (Sinewave) F=1 kHz R= 10 Kohm V= 4 volt Find and Sketch the…
A:
Q: Determine the ripple factor for the filtered rectifier circuit below when RL= 4KN. Then explain…
A: In the circuit, Full wave bridge rectifier is given. Find the ripple factor? R and C are given.
Q: Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical…
A:
Q: Draw and explain the circuit of a simple AM demodulator using Junction diode
A: according to question we have to draw and explain the circuit of a simple AM demodulator using…
Q: Q.1 (a) (i) State three differences between the Field Effect Transistor (FET) and the Bipolar…
A: i) Difference between FET and BJT: BJT is a bipolar junction transistor since it stands for bipolar…
Q: Determine the gate trigger current and the anode current when the switch, SW1, is momentarily closed…
A:
Q: A 5-bit flash converter has a reference voltage of 16 V. What is the center code voltage for a…
A: The solution is given below
Q: A PMMC instrument with FSD = 50µA and Rm =2.2k2 is to be employed as an ac voltmeter with FSD=220V…
A: The basic circuit for enhancement of voltmeter is as shown below:
Q: For the JFET shown in Figure, Determine the minimum value of VDD required to put the device in the…
A: Need to find VDD By drawing diagram and applying KVL
Q: What value of filter capacitor is required to produce 1% ripple factor for a full-wave rectifier…
A: Given data, Ripple factor, r = 1% = 0.01. Load resistance, RL = 1.5 kΩ=1500 Ω. Load voltage, VL =…
Q: An analog-to-digital converter (ADC) advertises an accuracy of + the least significant bit (LSB). If…
A: Given : In the question they have mentioned the ANALOG TO DIGITAL converter (ADC) with having the…
Q: |(a) Draw the circuit diagram of 2-bits flash (simultaneous) method analog to digital converter and…
A: a) We need to draw the circuit diagram of the 2-bits flash (simultaneous) method analog to digital…
Q: Construction and Characteristics of JFETs a. Draw the basic construction of a p-channel JFET. b.…
A: Given We need to draw the construction of a p channel JFET and also sketch depletion region in case…
Q: The waveforms shown in figure (1) the output waveforms of as an astable multivibrator using 555…
A: When Vo = 5 V, capacitor gets charged towards 5V. So capacitor gets charged during the interval…
Q: What is the rms ripple voltage of a fullwave rectifier with an output voltage of 10 Vrms?
A:
Q: The Type K thermocouple has a sensitivity of about 41 micro-Volts/℃, i.e. for each degree difference…
A: Step 1:ADC stands for analog to digital conversion.The numbers of bit in ADC represents the voltage…
Q: describe and compare the different types of Analog to Digital Converters(Advantages, Disadvantages,…
A: Analog to digital converters are used within a data acquisition system is to convert conditioned…
Q: Homework: What is the accuracy of a 16-bit ADC if the converter encodes an analog voltage between 0…
A:
Q: Q4: Using 4-bits successive approximation A/D converter, explain (with sketching the required…
A:
Q: Explain construction and working principle of JFET. Also draw drain and transfer characteristics of…
A:
Q: Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical…
A: Introduction: Bridge rectifier is full wave rectifier circuit, converts AC in DC. Transformer steps…
Q: Explain in your own words some of the trade-offs between CISC and RISC.
A: The architecture of computer has the following types: Reduced Instruction set computer (RISC)…
Q: For the given circuit, what is the minimum peak value of the output waveform if the input waveform…
A:
Q: The primary to secondary turns ratio of a transformer used in a Half wave rectifier is 20:1. The…
A:
Q: A 4:1 transformer is connected to a bridge rectifier circuit with a 1kΩ load. What is the peak…
A: First we will find out output voltage then output current .
Q: Which cannot be done with an input source, a zener diode and a resistor? Rectifier circuits…
A: In this question , we will write about zener diode...
Q: amplifier circuits? а. Photodiodes b. Transistors С. Zener diodes d. Rectifiers
A: In this question, we will write which is used in an amplifier...
Q: 7. A PFC circuit is designed with the following parameters. Vin = 100Vrms, Vout = 400V, Iou=2A. What…
A: Vin=100VrmsVout=400VIout=2 A
Q: List the examples for Signal processing element and Explain about any one kind of Analog to Digital…
A: Signal processing focuses on analyzing, modifying and synthesizing signal like sound, light, audio,…
Q: 20: Given ddc=0.98 determine Bdc' O Given Pdc=120 , determine the cortesponding valwe of c Given…
A: From the question, we have to find α, β, IE and IB αDC=0.98 βDC=αDC1-αDC βDC=0.981-0.98 βDC=49
Q: describe and compare the different types of Analog to Digital Converters(Advantages, Disadvantages,…
A: Analog to Digital Converters types and comparison,
Q: The Type K thermocouple has a sensitivity of about 41 micro-Volts/℃, i.e. for each degree difference…
A: The resolution of the 16 bit ADC is
Q: An analog signal voltage in the range of 0 to 8V is divided into 16 equal intervals by a quantizer.…
A: The analog voltage range is 0 V to 8 V. The number of equal division is 16.
Q: 7. A PFC circuit is designed with the following parameters. Vin = 100Vrms, Vou = 400V, Iou=2A. What…
A: Note: We are authorized to answer one question at a time since you have not mentioned which question…
Q: An 8-bit analog to digital converter has a reference voltage of 5 Volts. (i) Find the digital output…
A:
Q: 8. What value of filter capacitor is required to produce 1% ripple factor for a full-wave rectifier…
A: We need to find a capacitor to limit the ripple to 1%
Q: What is the peak load voltage out of a bridge rectifier for a secondary voltage of 12.6 Vrms? (Use…
A:
Q: Describe the working of Flash type Analog to Digital converter with a neat diagram.
A: Consider the circuit diagram of a 2-bit Flash Type Analog-to-Digital Converter (ADC).
Q: Q/For a Binery Erasure Channel ( BEC ), the input probability for 0/35 and Pe of the channel is 0.15…
A:
Q: In a common base configuration, collector current is 1.95 milliamperes and base current is 0.05…
A: In this question, If base current IB = 0.05mA And collector current Ic = 1.95mA Then find the…
Determine the % resolution of a 10-bit A/D converter for a given reference voltage of 100 volts.
Step by step
Solved in 2 steps with 1 images
- Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary. * D3 Di 110 V Vpsec) D2 RL D 10 k . Vp(out)= 14.6 V, PIV= 14.3 V O vp(out)= 16.5 V, PIV= 13.6 V Vp(out)= 13.6 V, PIV= 13.3 V O vp(out)= 15.6 V, PIV= 16.3 V ell elll3. For the half-wave rectifier given in the figure below, find the average values of the output voltage and current, and the ripple factor of the output voltage. D1 Io Dbreak R1 1k vo VAMPL = 169.71 FREQ = 50Describe the nature of the output voltage out of half – wave and full – wave rectifiers with that of the input voltage. D: O VoIE, AF GEN. RL 60 Hz / 100 Hz V./E. R1 2.2 k + AF GEN. RL 60 Hz / 100 Hz R2 2.2 k D2 b 10K
- The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. the direction of conventional current flow O c. that it is a P-channel MOSFET O d. the direction of electronsa full-wave rectifier with a capacitor-input filter provides a dc output voltage of 35V to a 3.3k ohms load. Determine the minimum value of filter capacitor if the maximum peak-to-peak ripple voltage is to be 0.5V.Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
- Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary. D3 110 V Vpisec) RL 10 kN- Vploun) alll lollDesign the power supply using diode components. This power supply sholud have 2 outputs. 12Vdc and 5Vdc. Input 240 Vac Supply i. Draw the circuit diagram ii. Bill of material/components that will be used iii. Teh output waveform for each stageDraw and explain the circuit of a simple AM demodulator using Junction diode ( draw the input and output waveforms )