Answered: Determine the bending moment of point…

Determine the bending moment of point D. The supports at A and B are journal bearings. Supply the answer in kilonewton-meters. 2 kN/m C D -600 mm- 450 mm- 300 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Related questions

Q: Draw the shear and moment diagrams for the loaded beam. After you have the diagrams, answer the…

A: The expression that can be obtained by taking moment about point A is, MA=7 kN×3 m+12×7 kN/m×10 m×18…

Q: The rod has a diameter of 0.5 in. and a weight of 5 lb/ft. i) Calculate the torque and bending…

A: Given data: Diameter of the rod D = 0.5 in = (0.5/12) = 0.04167 ft weight of the rod, W = 5 lb/ft If…

Q: A kN m 2 m 120 2 m 100 kN C kN m 2m 120

A: To Find : The maximum the maximum shear and bending moment that occur in the span also draw shear…

Q: at the top to 90 kPa at the bottom. As an additional support, it is anchored at depth y = 2 m. with…

A: cantiliver retaining wall is subjected to a soil pressure linearly varying from zero at the top to…

Q: The internal bending moment at point B (in N.M) is 200 N/m A IB – 3 m- -3 m-

A: Let's mark the points B, C, D, E, G as shown in below figure. Let's make a section S-S at B to find…

Q: 3 ft 100 lb B 5 ft CO 40 lb/ft Ꭰ 4 ft

A: Find the most critical point in the beam. Most critical point is the point where maximum bending…

Q: 1. Use moment-area method and determine the slope at A and C and displacement at B. E = 200 GPa, I =…

A: Use Of Moment Area Method

Q: Determine, to the nearest millimeter, the smallest allowable diameter of the shaft which is…

Q: Wo Determine the magnitude and location of the maximum bending moment M fastttt it's urgent

Q: 10 kNim 50 kN Identify the moment diagram of the beam shown. 3125 3125 (AN mA 022 (AN-m)A

Q: Determine the internal loads diagrams of the beam above. In the cell bellow give the value of the…

A: According to the details provided in the question, we need to calculate we need to draw SFD And BMD…

Q: Plot the bending moment diagrams of the rigid frames shown below. Pa 2 kN/m 4. 20 M

Q: Draw the shear and moment diagram and determine the Vmax and Mmax of the cantilever beam shown…

A: To find : The shear and moment diagram and also the value of Vmax and Mmax. FBD: Free body diagram…

Q: Determine the absolute maximum bending stress in the 1.5-in.-diameter shaft. The shaft is supported…

A: Given data: Diameter of the shaft , d = 1.5 in. Let, Y = distance between neutral fibre and…

Q: 3kN/m 3kN/m F- -2.25m. 4kN/m

A: Drawing the Free Body Diagram of the beam, Taking moment about…

Q: Determine the resultant internal bending moment acting on the cross section at point C in the beam…

Q: Draw the bending moment diagram. 15 kN 10 kN/m 20 kN · m В A 2 m 1m 1 m 2 m

A: Given: Point Load=15kN Moment=20kN.m Uniform loading=10kN/m

Q: 450 lb/ft Q2/ If the beam has a square cross section of 9 in. on each side, determine the absolute…

Q: ure. The bending moment at 0.5 m from the support is approximately

A: To determine the bending moment at 0.5 from support.

Q: Determine the smallest allowable diameter of the shaft. The shaft is supported by a thrust bearing…

A: Given data Allowable bending stress, σ = 22 ksi. Draw the free-body diagram of the shaft. Apply…

Q: Q5/ If the beam has a square cross section of 9 in. on each side, determine the absolute maximum…

Q: Question 4 Solve for the maximum moment developed in the beam. Express answer in KM-m 6m 1,800N…

A: Given data: ◆ The point load acting at the mid-span of the simply-supported beam: P = 1800 N ◆ The…

Q: 29.11 KN /m -(x 4.5m A x Ma 2.12 m Ay ↑ 一 29.97 kN/m

A: Shear force at any section is found by the summation of all the shear force on either left or right…

Q: The shaft is supported by a smooth thrust bearing at A and smooth journal bearing at C. If d = 3…

A: The bearings at A and C will be replaced by two vertical reactions because there is vertical load…

Q: HW. Determine the maximum bending stress location along the beam. at ang 200 m 700 N/m Iso 500 N.m…

Q: For the beam shown below: 1- Draw the shear and moment diagrams. 2- Determine the absolute maximum…

Q: Determine the bending moment acting at each of the following locations: (a) x = 10.5 ft (i.e., at…

A: we have to determine the support reaction and shear force

Q: Determine the absolute maximum bending stress in the 2-in.-diameter shaft. There is a journal…

A: Given data: Diameter of shaft = 2 in To determine: Absolute maximum bending stress Before…

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Dar the…

Q: Determine where the maximum displacement of the following beam is happening and what its value is.…

Q: The stepped bar has a thickness of 10 mm. Determine the maximum moment that can be applied to its…

A: Given data: The thickness of the stepped bar is t = 10 mm. The allowable bending stress is…

Q: Determine the shape factor of the cross section.

A: cross section of this image is made of 5 square with size "a" as shown in fig. We will find…

Q: 2. A shaft made of mild steel. The supported length of the shaft is 3 meters. It carries two pulleys…

A: From the figure it is clear that the beam is subjected to symmetric loading Therefore, RA=RB…

Q: The curved beam is made from a material having allowable bending stress of sallow = 24 ksi.…

A: Given Data Allowable bending stress is: σb=24 ksi=24000 psi

Q: Total upward force of 100 lbs is applied. Determine the forces at D and F on the ADF tong. Where is…

A: Total upward force is 100 Lbs. Since, the tong is symmetric about the vertical axis, the total load…

Q: Determine the maximum bending stress in the beam’s cross section.

A: The expression for the moment of inertia of the section about x-axis, Iz=bd312 Here, bis the breadth…

Q: can you solve this?

A: Draw the free-body diagram of the beam.

Q: Draw the free body diagram, shear force diagram, and bending moment diagram for the beam shown below…

A: Consider the triangle CBD, the angle BDC is, The free-body diagram for the beam is shown below,…

Q: Determine the bending stress at B in MPa. [M = 100 kN.m; Ix 0.1907 x 103 m: 9= 0.0975 m] 300 mm LA…

Q: Determine the bending stress at point A of the beam, and the orientation of the neutral axis. Using…

A: The moment of inertia about the y' axis is given by My'=-3sin45°=-2.121 kip·ft The moment of inertia…

Q: 10 kN/m A B |C -3 m· -3 m– 150 mm- - 30 mm 150 mm 30 mm-

Q: The bending moment Mis 3 m M

A: Given data : Point load=P Distance from point load to a point where moment is to be found=d…

Q: Sketch the shear force and bending moment diagrams. Neglect the weight of the beam. y 15 kN 30 kN -2…

Q: 6 kN 2 kN 12 m 3kN/m 4 m 750 N/m 18 m 3 m 4 m 3 m

Q: If the beam in Prob. 6–28 has a rectangular cross section with a width b and a height h, determine…

A: Given Data: The load acting on the beam is 12 kN and 20 kN. The free-body diagram of the beam can…

Q: Determine the bending stress in a 1-meter simple beam with a concentrated load of 1.25 kN at…

A: Given:P=1.25*103 Nb=2 inh=4 in

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Determine the bending moment of point D. The supports at A and B are journal bearings. Supply the answer in kilonewton-meters.
2 kN/m
C
D
-600 mm-
450 mm-
300 mm

Expert Solution

Step 1

Step 2

Step by step

Solved in 3 steps with 3 images

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b=8.0 ft, c=4.0 ft, d=3.0 ft, w = 6.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a B a W B W C b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) b C C P C D P Ľ E d E ·x Ey
The shear strain is calculated using the torque and the polar moment of inertia. Select one: a. True b. False
If P is equivalent to 94 kN, the diameter at pin B is Blank 1 mm.
Question 17 A wide flange section has the following properties: bf = 200 mm tf = 8 mm d = 300 mm tw = 11 mm Calculate the radius of gyration in mm about the y-axis.
(i) Draw Torsion and Bending Moment Diagrams to calculate the moment and torsion in the 250-mm section of shaft. 250 mm 100 mm
The 1.5-in diameter solid steel shaft is simply supported at the ends. Two Pulleys are keyed to the shaft where pulley B is of diameter of 4 in and pulley C is of diameter of 8 in. Transverse shear stress needs to be considered. 1) Draw the bending moment diagrams of shaft AD for My and M₂, and indicate the location and the magnitude of the maximum bending moments. 10 in 200 lbf 1000 lbf 10 in 500 lbf 100 lbf 10 in F G E
Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions are provided. MB = 143 kN-m Mc = 51 kN-m Ay = 16.17 kN (down) Dy = 16.17 kN (up) 1997 4 m 5 m O 80.9 kN-m O 74.1 kN-m O 94.5 kN-m O 50.4 kN-m O 60.6 kN-m 3 m D X
Part B Draw the moment diagram for the shaft. Click on "add vertical line off" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. 600 N-m 0.8 m 0.8 m 0.8 m No elements selected 900 N M (N m) 1000 900 800 700 600 500 400 300 200 100 I (m) 0+ -1000.0 0.2 0.4 0,6 0,8 1.0 12 1.4 1.6 1,8 2.0 2.2 -200 + -300 -400 -500 -600 -700 -800 -900 -1000 Add discontinuity lines and select segments to add to the canvas.
Solve for the Following Bending moment equation for segment BC. a. 2000 lb(X) - 100 lb/ft (X squared) - 9600 lb-ft b. 2100 lb(X) - 120 lb/ft (X squared) - 9700 lb-ft c. 21500 lb(X) - 200 lb/ft (X squared) - 9800 lb-ft d. 3000 lb(X) - 200 lb/ft (X squared) - 9850 lb-ft The distance between point A and the shear force VAB=0 a. 6 feet b. 8 feet c. 10 feet d. 12 feet The degree of bending moment equations for segments AB and BC. a. 1st degree and 2rd degree b. 3rd degree and 2nd degree c. 2nd degree and 3rd degree d. None of the above.
The column shown is fabricated from two C250 x 30 standard steel shapes (see Appendix B for its cross-sectional properties) that are oriented back-to-back with a gap of 33 mm between the two channels. The column is fixed at its base and free to translate in the y direction at its upper end. Translation in the z direction, however, is restrained at its upper end. A load P is applied at an offset distance of 430 mm from the channel flanges. Use the AISC equations given in Section 16.5, and assume that L = 4.1 m, s = 33 mm, E = 200 GPa, oy = 275 MPa, and (Gallow); = 145 MPa. Offset - distance e P Lateral bracing in z direction C250 x 30 L C250 x 30 Cross section.
Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions and the shear-force diagram are provided. M = 13 kN-m Ay = 3.46 KN Dy Units: KN = 32.54 kN M 4 m 29.5 kN-m 43.3 kN-m 25.8 kN-m O 22.9 kN-m 31.48 kN-m B Ay 4 m 15 kN C Ay 4 m Ay-15 7 kN/m D 3 m 21 Ay-15 E X
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.