Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). Volvolt) 2- The ripple voltage. Vm = 12 V 3- The Vdc value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. (assume ideal diodes) = 0.1 V T= 0.01 sec. t(sec.)

Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). Volvolt) 2- The ripple voltage. Vm = 12 V 3- The Vdc value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. (assume ideal diodes) = 0.1 V T= 0.01 sec. t(sec.)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
Q2) A 3-phase, half-wave thyristor converter is connected through a voltage source 150 V as input voltage and used to supply resistive load of 10 2. Determine rsm voltage, rms current, ripple factor and dissipated power in the resistor R. If a = 45° and f = 50 Hz. %3D
Draw the full-wave voltage doubler circuit diagram. When a 1:4 transformer is used in this circuit andIf Vo=12sin(314t) alternative signal is obtained at the output, the frequency of the input signal, maximum and rmsCalculate its value.
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
6. A 1-phase full converter delivers ripple free current to RL load with R=1592. The source voltage is 230V, 50Hz, for a=30°. Determine rectification efficiency, voltage ripple factor displacement factor, and power factor
C. A single phase full converter feeding RL load has the following data: source voltage 230V(RMS), SOHZ.R-2.52 L=very large, firing angle -30"f the load inductrance is large enough to make the load current constant then i Sketch the time variation of sounce voltage source current, load voltage, load current current through one thyristor and voltage across it H. Compute the average value of load voltage and load current, Derive the formula.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Q2) A 3-phase, half-wave thyristor converter is connected through a voltage source 150 V as input voltage and used to supply resistive load of 10 N. Determine rsm voltage, rms current, ripple factor and dissipated power in the resistor R. If a = 45° and f = 50 Hz.
all äabl (CME 446) 1 If F3=0.1 and Z3=45 Q, then the impedance of the next stage in the multi-section transformer is: of O a. 40.5 stion O b. 49.5 O C. 55 O d. None O e. 36.8 s page Next page
Design a flyback converter for an input of 24 V and output of 40 W at 40V. Specify the transformer turns and magnetizing inductance, switching frequency and capacitor to limit the ripple voltage less than 0.5%.