So Far?CompletionDescribe what will happen to the resistance offered by a conductor given the following changes in itsproperties:Increase in electrical resistivityDecrease in electrical conductivityLowering of temperatureIncrease in lengthFattening2. Describe what will happen to the current flow through a conductor given the following changes in itsproperties:Decrease in electrical resistivityIncrease in electrical conductivityIncrease of temperatureDecrease in lengthThinning II-Problem SolvingA. Current1. Calculate the current produced by a charge of 4.15 x1017 C that flows for 10 s.2. Identify how many electrons flow through a lightbulb for each second if the current through the bulb is0.75A.3. A steady current of 0.75A flows through a conductor. Determine the number of charges that passesthrough the wire in 3 minutes.4. Determine the number of electrons that pass per second through a section of wire carrying a current of 0.8 A.B. Resistance1. Solve for the resistance of a conductor given a resistivity of 15.3 Q.m, length of 6 m , and crosssectional area of 2.85 10² m².2. A copper rod is 3m long and 4 mm in diameter. Compute its resistance if the resistivity of the material is1.76 x10 2.m.

1) The resistance offered by the conductor is given by: R = ρLAρ = resistivityL = length of the…

Describe what will happen to the resistance offered by a conductor given the following changes in its properties: Increase in electrical resistivity Decrease in electrical conductivity Lowering of temperature Increase in length Fattening Describe what will happen to the current flow through a conductor given the following changes in its properties: Decrease in electrical resistivity Increase in electrical conductivity Increase of temperature Decrease in length Thinning

Describe what will happen to the resistance offered by a conductor given the following changes in its properties: Increase in electrical resistivity Decrease in electrical conductivity Lowering of temperature Increase in length Fattening Describe what will happen to the current flow through a conductor given the following changes in its properties: Decrease in electrical resistivity Increase in electrical conductivity Increase of temperature Decrease in length Thinning

Inquiry into Physics

8th Edition

ISBN:9781337515863

Author:Ostdiek

Publisher:Ostdiek

Chapter7: Electricity

Section: Chapter Questions

Problem 35Q: (Indicates a review question, which means it requires only a basic understanding of the material to...

See similar textbooks

Similar questions

PLEASE ANSER THIS EXERCISE. THIS IS NOT A GRADED QUESTION. 1. Good thermal conductors are said to be good electrical conductors. If so, why is it that cords used to connect toasters, irons, and heat-producting apoliances get hot by the conduction of heat from the heating element? 2. How would you expect the resistivity of a good insulator such as glass or polysterene to vary with temperature? 3. A fuse is a device that is designed to break the circuit. It melts when the current exceeds its value. What characteristics should the material have?
pplied 2. Find the ratio of the diameter of aluminium to copper wire, if they have the same resistance per unit length. Take the resistivity values of aluminium and copper to be 2.65x 10-" 2 m and 1.72 × 10-® m respectively. Answers to the following question will be relevant for the in-labs. Please note your answers when going in for the main lab session. 3. Ohm's law can be sated as V = IR. a. Suppose in an experiment, data is collected of the variation of current with resistance R. Next a plot of R vs 'is made. How does one determine the
The system of resistors shown in figure 1 has an effective resistance of 1.50. Calculate the resistance R of the upper resistor. Figure 1: A system of resistors.
Examine the diagrams below. They show models of the molecular structuresof two materials that an engineer is using to design an electric circuit. Material A has a low resistivity. Material B has a high resistivity. Identify the material that would be classified as a conductor and the one that would be classified as an insulator. Then explain how the molecular structure of each material determines whether it resists or allows the flow of electric current.
DIFFERENTIAL EQUATION: Electric Circuits. Solve the following problems. Show your complete solution. When a resistance R (ohms) and a capacitance C (farads) are connected in series with an emf E (volts), the current I (amperes) is given by the equation: dI 1 dE +-I = dt C R dt If R = 1000 ohms, C = 5x10-4farad.and I = 10 amperes for t = 0, find the current for t = 1 second and E = 100 volts.
Q5: Derive the expression for power P = VI in an electrical circuit. Q6: What is the resistance of an electric arc lamp, if the lamp uses 20A20A when connected to a 220 volt? Q7: A 162 resistor is connected to a 48v battery. What is the charge flow through it in one minute? Q8: A wire having an area of cross section = 6mm? and another wire having an area of cross section 10mm2, have the same length and are made up of the same material. Which wire has more resistance? Q9: In two minutes, 120C of charge flow through a conductor. What is the current flowing through it and the voltage across the terminals if the resistance of the conductor is equal to 22? Q10. 100 cm length of wire that is 1.5mm2 in cross section has a measured resistance of 12. Calculate the resistivity of the used material. Q11. Some homes use solid wire having a cross-sectional area of 4mm2 to provide electrical distribution to outlets and light sockets. Determine the resistance of 24 meters of this solid wire.…
Please complete all parts, each part is needed in order to complete the next question. The parts correaltes with eachother. (part 1 of 2) Consider a series combination of 2 resistances. 25 Ω 30 Ω What is the equivalent resistance?1. 55 Ω2. 1.2 Ω3. 0.83 Ω4. 5 Ω (part 2 of 2) Consider a parallel combination of the sameresistors. 25 Ω 30 Ω What is the equivalent resistance?1. More than 30 Ω2. Between 25 and 30 Ω3. Less than 25 Ω4. More information is needed
Given a set of six (6) 1.5 V cells. Show by means of a diagram how would you connect the FOUR cells to obtain a total voltage of: a.) 3V b.) 4.5V Indicate also where a voltemer should be connected in order to read the total voltage.
Can you pls help me solve this. 5 resistors are connected as shown in the figure. The voltage on AB is 30V and the total resistance is 2 ohms. The voltage across resistor 1 is 14.25V and the current passing resistor 3 is 6 amperes. Determine the total current of the circuit and all other unknowns (r4 = 6 ohms, r5 = 10 ohms) Solve for: (a) Resistance of R2 (b) current through I4 (c) current through I1 (d) voltage across R4 (e) voltage across R2 (f) voltage across R3 (g) Total current *Pls refer from the photo attached* •Pls answer with complete and detailed solution (3 decimal places all final answers with correct units) •Sketch an illustration/diagram with labels (this is a must; for a better understanding) Thank you I will give your answer a LIKE for helping me... **Pls refer from the photo attached. •Pls answer with complete and detailed solution (3 DECIMAL PLACES all final answers with correct units) •Sketch an illustration/diagram with…
Determine the voltages and voltage changes indicated based on the circuit diagram below. Hint, first compute the total current by dividing the net voltage (you need to subtract because the power sources are in opposite directions) by the total resistance. Once you have the total current you can determine the change in voltage through the resistors. The notation goes...Vab=Va-Vb Va= Answer 1 V Vb= Answer 2 V Vc= Answer 3 V Vd= Answer 4 V Ve= Answer 5 V Vab= Answer 6 V Vdc= Answer 7 V Vcb= Answer 8 V Vac= Answer 9 V Vdb= Answer 10 V
Q2: Design series ohmmeter using PMMC of 100Ω internal resistance and 0.4ma full-scale deflection current. The required half-scale deflection is equal to 9kΩ.[use a battery of 9v]. Sketch the internal circuit diagram of the ohmmeter. Sketch also roughly the scale of the designed meter.
Consider the following electrical circuit ... R1 R3 R2 The current through the circuit (in amps) is determined by the voltage through the circuit (in volts) divided by the resistance (in ohms) through the circuit. Complete the script to calculate the total current through the circuit This is the script for calculating the total current of the circuit R1 = 5; R2 = 10; R3 = 2; V = 6; RI = 1/( (1/Blank 1)+(1/Blank 2)) +Blank 3 I = Blank 4/Blank 5 Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer Blank 4 Add your answer Blank 5 Add your answer