Derive the truth table, simplified equation, and logical diagram. 1.Design a 4-bit majority circuit. A majority circuit detects that the number of 1’s in the input is greater than the 0’s. 2.Design a 4-bit combinational circuit that detects at least 2 consecutive 1’s. 3.Design a 4-bit combinational circuit that adds one (1) to the input.

Derive the truth table, simplified equation, and logical diagram. 1.Design a 4-bit majority circuit. A majority circuit detects that the number of 1’s in the input is greater than the 0’s. 2.Design a 4-bit combinational circuit that detects at least 2 consecutive 1’s. 3.Design a 4-bit combinational circuit that adds one (1) to the input.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Electrical Engineering Verilog Design N-bit binary counter which counts the number from 0 to 2N-1. After reaching to maximum count i.e. 2N-1, it again starts the count from 0. i. Write the description of the counter in Verilog ii. Generate the design from the listing ii. Produce the waveforms of the counter
Design a combinatorial circuit that will be able to detect prime numbers given as input in binary. The input to the system will be any 4 bit binary number. The output of the circuit should be a single bit that will be 1 (high) if the input is a prime number and 0 (low) if the input is not a prime number. For example, if the input to the circuit is 0101 the output should be 1. Again if the input is 1010, the output should be 0.
Design a combinational circuit whose input is 4 bit binary number and output is 1’s complement of the input. And also design a combinational circuit from the same input that represents a decimal digit in BCD and four output lines that generates the 9’s compliment of the output.
3. Design and Show the connection on the circuit that would add two 6-bit data, D: (D6 Ds Di) and H: (H6 Hs Hi). You may use 4-bit adders. Draw the circuit and clearly indicate/identify all input and outputs. Show addition of Ds to Hs and Sum (Es). Do not draw switches, resistors, and LEDS at inputs or outputs. 7483A 7483A A. A, A, A1 B. B. B, B, B. B. B, C, C. C. C. B,
Excess-3 code is significant for arithmetic operations as it overcomes shortcoming encountered while using 8421 BCD code to add two decimal digits whose sum exceeds 9. Excess-3 arithmetic uses different algorithm than normal non-biased BCD or binary positional number system. An electronics company has hired your services to design a code converter that converts Binary Coded Decimal (BCD) code for it. Design the converter.
- The proportional distribution of A, B, C, D signals is given in the table as a percentage. It “logic 1” when the signals are accepted as active, “logic 0” when they are accepted as passive. takes. - When the proportional sum of active signals is over 50%, its output is "logic1", When we accept "logic 0" when it is below 50%, the output in the table Find the values. - Create an X function based on the logic values you find. Simplify the created X function. - Design the simplified function with NAND and NOR gates. - Set up the circuits you designed with NAND and NOR gates and observe the outputs. Show the output values by drawing a table, applying all possibilities to the input values.
- The proportional distribution of A, B, C, D signals is given in the table as a percentage. It “logic 1” when the signals are accepted as active, “logic 0” when they are accepted as passive. takes. - When the proportional sum of active signals is over 50%, its output is "logic1", When we accept "logic 0" when it is below 50%, the output in the table Find the values. - Create an X function based on the logic values you find. Simplify the created X function. - Design the simplified function with NAND and NOR gates.
Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.
Design Problem 2: As an engineer you are required to design a circuit which has input Excess-3 number in binary form as A, B, C, D with A as MSB and D as LSB, and generate BCD output in binary form as W, X, Y, Z with W as MSB and D as LSB. Also implement your design to verify your results. Conditions are as. · Whenever result exceed than number of output bits or in negative value or invalid, it does not matter for you. · You should make up truth table accordingly. · Draw its logic diagram. · Implement simplified logic diagram which shows BCD output in Multisim
Derive the circuits for a three-bit parity generator and a four-bit parity checker using an odd-parity bit.
5. In the circuit implementation of an 8-bit adder, explain why the carry bit connection of the least- significant bit is connected to ground. Explain in words what values for A, B, C, D, E will cause a 1 to appear at point X. The circuit below uses a 5-input AND gate. Draw the equivalent circuit using only 2-input gates.
2- Show how two 7483 a four-bit parallel adders can be connected to form an eight- bit parallel adder. Show output form P,PGPSPAP3P2P1PO=10111001 and Q,Q,QgQ,Q3Q2Q,Qo=10011110