Define the types of piles on the basis of their function with sketches.
Q: Why does The O-cell typically is attached to the tip end of a pipe pile prior to installation…
A: The Osterberg Cell is a hydraulically operated device fitted in the foundation. It is of high…
Q: he soil profile and soil properties at a site are shown in the table below. A group of 12 concrete…
A: Given data : Number of Piles : 12 3 x 4 matrix L = 12m D = 0.45m Pile spacing 1.5m S = 3D =…
Q: State the outcome of driving a displacement pile into a loose sand and plastic clay?
A: The outcome of driving a displacement pile into a loose sand and plastic clay are listed below:
Q: Explain the difference between short piles and long piles.
A: Short pile : - Short pile are generally 2m to 4m and from 250 mm to 350mm diameter. - The piles may…
Q: What soil properties are needed for estimating bearing capacity of driven piles and drilled shafts?…
A: We are authorized to answer one question at a time, since you have not mentioned which part you are…
Q: Q # 1. What is pile foundation? Discuss the classification of pile based on materials/composition…
A: Pile foundation- a foundation laid with deep pile is known as pile foundation.
Q: Define the Types of piles and their functions ?
A: The different types of piles are: 1.End bearing 2.Friction piles 3.Friction and cohesion pile
Q: What are the advantage of the augered-excavation cast-in-place piles?
A: Augered cast in place piles are defined as the type of drilled foundation. These piles are installed…
Q: How is a piling foundation defined? Distinguish piles according to their materials/composition and…
A: Pile Foundation also known as deep Foundation, this is a suggested for a soil of poor strength or…
Q: Explain why are most marine piles circular in cross section?
A: Marine piles are circular in cross-section because: 1. Circular piles has high column buckling…
Q: Explain why pile driving formulas are not reliable, and why a wave equation analysis is a better…
A: Solution: Pile driving formulas are not reliable because Pile Driving formulas are very simple.…
Q: 3- Describe the methods of stabilizing the sides of the excavation when making piles in loose soil…
A: A number of fundamental considerations should be taken into account while designing stable sides.…
Q: State the different types of piles according to its function and construction?
A: The types of piles are:End bearing piles: These pile have strong ends so as to resists the load and…
Q: Define driven piles.
A: There are two types of foundations are there: Shallow foundation Deep foundation A shallow…
Q: Describe the categories of the structural loads applied to piles.
A: pile is the long cylindrical member made up with material which having high compressive strength .…
Q: Describe the Arrangement for Piles in a Group.
A: If applied load is large and then pile group is used rather than an individual pile. The individual…
Q: A single footings excavation project produced 150LCM soil , if the spoil bank has a conical shape…
A:
Q: Which one is a better choice, a large diameter piles or a system of several smallerpiles with the…
A: Piles plays pivotal role in stabilizing the superstructure. These are embedded vertically down into…
Q: Define Multiple piles
A: piles is a deep foundation. piles are used to carry vertical compressive load as well as resist…
Q: 3- Describe the methods of fixing the sides of the excavation when making piles in loose soil or…
A:
Q: In piling works, normally founding levels of bored piles are defined by using total core recovery or…
A: Piling is defined as being foundations that are driven or bored through the ground along a certain…
Q: Explain the Correlation of pile shaft adhesion factor α and soil cohesion.
A: Piles in clay generally carry most of the load by virtue of skin friction.
Q: A 3 x 3 pile group with pile spacing of 1 m and pile diameter of 0.40 m supports a load of 3 MN.…
A: The load on the pile is P=3 MN. The void ratio is e=0.65. The coefficient of consolidation is…
Q: A frictional pile with a circular cross- section (diameter = D) is pushed into the soil to a…
A:
Q: Should engineers rely solely on Hiley’s formula in the design of H-piles?
A: Hiley Pile driving formulae: Hiley's pile-driving formula is described below according to IS:2911.…
Q: Describe about the Uplift Capacity (Single Pile).
A: The uplift capacity of piles is used to predict the capacity of piles under uplift loading. This is…
Q: A bored pile of 0.8 m in diameter is constructed in sand. Soil conditions and relevant soil…
A:
Q: Why there is need of pressure piles?
A: Answer Pressure pile used in the foundation engineering under following condition given in step 2
Q: The length of friction piles based on O Shear strength of soil O Pile size O applied load O all of…
A: 6. The length of friction piles based on: The loads are transferred from the structure to the soil.
Q: 1. What types of piles you know by their bearing mechanism
A: The various types of piles are: Sheet piles: This type of pile is mostly used to provide lateral…
Q: An anchored sheet pile is to support a mass of cohesionless soil up to a height of 6 m above ground…
A: Given Unit weight of soil=21 KN/m3 Angle of internal friction= 30°
Q: Discuss about the Carrying capacity of single pile in granular and cohesive soil ?
A: The load bearing capacity of foundation soil or rock which enables it to bear and transmit load…
Q: Discuss the method of obtaining ultimate load and also allowableload on a single pile from pile load…
A: Pile load test is the in situ method of the calculation of the load and settlement. This method is…
Q: Q4: It is required to construct a pile foundation comprised of 25 piles arranged in 5 columns at…
A: Given that Total imposed load= 3000 kN The diameter and length= 50 cm and 12m The water table was…
Q: Describe the factors of safety for design of piles.
A: Answer IntroductionA pile foundation is a cylindrical structural member made of concrete, steel, and…
Q: For a rigid pile cap with vertical piles at the middle and raking piles at the sides,what is the…
A: Brief concept- Piles are provided in the deep foundation where the applied load is very high and the…
Q: Define what are displacement piles ?
A: Driven piles, also referred to as displacement piles, are a commonly-used sort of building…
Q: Compare features of cast in place piles: a) Constructed by a driven steel shell with concrete b)…
A: Cast in-situ pile:Cast-in-place (Cast-in-situ) piles are those piles that are cast in position…
Q: Explain how wave equation analysis combined with static or dynamic load tests can be used to…
A: The wave analysis process is very important to know the relation between the pile capacities and…
Q: ).4 Determine the sheet-pile section modulus for the braced cut described in Problem 10.3. Given: o…
A:
Q: List the general types of pile drive hammers in use, and provide a brief description of the basic…
A: Pile Foundations are fitted with a special pile driving system known as a pile hammer. The hammer…
Q: Define Cast-in-drilled-hole (CIDH) pile
A: Cast-in-drilled-hole (CIDH) pile are simply reinforced concrete piles cast in holes drilled to…
Q: Elevati Distanc on (ft) (y- axis) e (ft) (x- axis) 5 15 10 17 10 18 15 19 15 28 33 40 -5 44 -5 54…
A: First find the excavation volume using the give values and then determine the volume of filling.…
Q: Compare circular, square and I section piles in terms of usage, cost and advantages/disadvantages?
A: Circular Piles Usage These sections require less material to construct and provide stronger and…
Q: An engineer is designing a deep foundation at a site underlain with loose to medium dense sandy silt…
A: The long circular section which is made up of hard material to carry loads and transfer it to hard…
Q: What is “block failure” in a group of piles and how does it differ from individual failure?
A: The cylinder which is long and used for carrying loads and transfer it to hard strata and made up of…
Q: Why would it be inappropriate to design a drilled shaft using a static analysis method developed for…
A: Static analysis is used to figure out: A pile's or a pile collective's nominal resistance in…
Q: Briefly explain the types of failures in pile groups.
A: Pile foundations are among the most common alternatives for heavy-duty constructions and those with…
Q: What’s the difference between a hammer cushion and a pile cushion? What are the purposes of each?…
A: The main piles are used for the structure above some height. Like a railway bridge or highway or…
Define the types of piles on the basis of their function with sketches.
Step by step
Solved in 3 steps with 2 images