Define the tools that must have during the Grinding Machine Operation

Q: A car is traveling from point A, B, C, D and E The car started from Point A with a speed of 5.5 m/s ...

A: Given dataAt point A, velocity=vA= 5.5 m/sTime taken for car to reach point B from point A = 60 sVel...

Q: The stress-strain diagram for a polyester resin is given in Figure 2. The rigid beam AC is supported...

A:

Q: Two 16-kN forces Pare applied to a 20 x 60-mm rectangular bar as shown. 10 mm 10 mm 30 mm 30 mm 25 m...

A: Given Data The load acting is: P=32 kN The dimensions of the block are: 20 mm×60 mm The breadth is:...

Q: Read the questions carefully and answer with complete solution and units.Use the steam tables provid...

A: Given Data: Pressure at the inlet of the turbine, P1=10 MPa The temperature at the inlet of the tur...

Q: Outside air at 15°C and 20% relative humidity is admitted at a volumetric rate of 15m³/min into an a...

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for...

Q: Determine shear

A: Given; Chip thickness ratio of the metal cutting of MS is;  r=0.5Where, Orthogonal cutiing of MS wit...

Q: A research team is interested in the difference between serum uric acid levels in patients with and ...

A: Soln For a population 1 Sample mean= 4.5 mg S1= 1 N1=12 For population 2 Mean = 3.4 S2= 1.5 N2= 15

Q: . Determine the Saturation Temperature and Saturation Pressure of the following

A: Determine the saturation temperature and saturation pressure.

Q: Determine shear stress in the shaft.

A: Given; A driving motor transmit power ,P= 45 kWAt a speed,N=450 rpmIf teh diameter of the shaft,d=30...

Q: Explain the different experimental methods that would relate stress with strain to determine the str...

A: Stress is the ratio of load acting on a cross-section to the area of cross-section. It is usually re...

Q: Problem 1: The pulleys are frictionless and of negligible weight. Determine Tension (N) in the cord ...

A: To find  Tension (N) in the cord supporting block B. Acceleration at Block A (m/s^2) Block B (m/s^2)...

Q: Saturated water vapor at 200.111 oC is isothermally condensed to a saturated liquid in a piston-cyli...

A:

Q: 3) Compute the centroid of the shaded area shown in figure Q.3 y R50 R30 120 100 25 50 Figure Q.3

A:

Q: A fluid with a shear rate of 0.5 per second, and the shearing stress 0.76 N per m2. What is its dyna...

A: Given     Shear stress = 0.76 N/m2        Shear rate = 0.5 per second Find   Dynamic viscosity

Q: Question (2) As shown in the Figure below, If the discharge was 0.0035 m/s. Calculate the water leve...

A: Find the level in the water tank. Given data :-  Discharge - 0.0035 m^3/sec.  

Q: Determine the difference in height h of the water column in the manometer if the flow of oil throug ...

A: Given   Discharge, Q = 0.04 m3/s           Density = 875 kg/m3 Find   Difference in height, h

Q: 1. Ea BHA jt 30.5 Ft Ea DP Stand 93.5 ft TDS + Hook block = 68 K Lbs Depth is 12800 Ft, Mud weight i...

A: a-P(0)=probality that oil is present =0.3P(70)=Probality that oil is not present 1-0.3=0.7P(G)= Prob...

Q: F W = 200 N Hy =0.3 Mk = 0.2 %3D If F = 540 N, will this box move? And how much is the friction forc...

A:

Q: Controlling the rate of flow in a hydraulic circuit allows for speed control of hydraulic cylinders ...

A: Controlling the rate of flow in a hydraulic circuit allows for speed control of hydraulic cylinders ...

Q: A uniform bar of length L, cross-sectional area A, and mass density p is suspended vertically from o...

A:

Q: Explain how does a basic drill press works.

A: Drill press :

Q: A cylindrical bar 120 mm long and having a diameter of 12 mm is pulled in tension with a load of 60,...

A: Given:  Load,       P = 60000 N Initial length,       L = 120 mm Elongation,         δ = 0.2 mm Diam...

Q: The number of pups in wolf dens of the southwestern United States is recorded below for wolf dens: 5...

A:

Q: F F F A C В If F = 50KN, AC = 2 m, BC = 5 m, then find moment at point B. %3D

A:

Q: Before the 400-kN load is applied, the rigid platform rests on two steel bars, each of cross-section...

A:

Q: A single-cylinder four-stroke diesel engine running at 2241 p.m. has a bore of 7.6cm and a stroke of...

A: Volumetric Efficiency:- Volumetric efficiency is defined as the ratio of actual suction volume of ai...

Q: The water in the vessel consisting of liquid and vapor in equilibrium at 8.547 Mpa. It has found out...

A: Given DataP=8.5MPaU=2138.545kJ/kg

Q: 4. Define welding?

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are poste...

Q: A single plate friction clutch with both sides of plate being effective is used to transmit power at...

A:

Q: Heat transfer problem Water flows through a thin-walled cylindrical tube of diameter 1 cm, maintaine...

A:

Q: A fountain ejects water through the two nozzles A and B, which have inner diameters of 10 mm. The fl...

A:

Q: 2 m -2 m E D 3m A B 1.5 m ▼F, F 300 N

A:

Q: How do you center a workpiece in a lathe machine with a four-jaw independent chuck?

A: Concept: 1) Generally this four jaw independent chuck is used to workpiece of different shape like s...

Q: 21. A horizontal pipe delivers steam at 1 MPa and a rate of 100 kg/s to a steam turbine. The pipe (O...

A: given; outer diameter (D1)=11.5cm                            =0.115minner diameter (D2)=96.5cm      ...

Q: Ipaliwanang ang Geothermal Energy At Geothermal Power Plant (Tagalog)

A: given; Geothermal Energy At Geothermal Power Plant (Tagalog)

Q: On a particular day a random sample of 12 tins of peas is taken from the output of a canning factory...

A:

Q: 2. For the following rheological model: or ww E2 2 (a) How is the behavior affected by changing E2 w...

A: The rheological properties of fluid are defined on the basis of the newton's law of viscosity  ζ=μdu...

Q: Determine the change in internal energy and enthalpy of water at 40°C and 3500 kPa if the temperatur...

A: To find change in internal energy & enthalpy

Q: Saturated steam has a pressure 2.356 Mpa. What are the temperature, specific internal energy, specif...

A:

Q: The 0.8-Mg car travels over the hill having the shape of a parabola. If the driver maintains a const...

A:

Q: The time taken to drill a hole

A: Given; Feed rate of a drill is;   f= 0.25 mm/revAt a rotating speed at, N= 300 rpmWhere, Plate thick...

Q: Objective: (i) Use the superposition method to verify your answer. (ii) Sketch V and M diagram for t...

A: Drawing the free body diagram as shown below, RA=12×L×qoRA=qoL2   At a distance x from the right en...

Q: A 1500 kg load is lifted by a hoist using a Ø1.5 m drum. The drum is driven by an electric motor.thr...

A:

Q: State the uses of each tools: 1. parting off tool 2.boring tool 3. undercutting tool 4. thread t...

A:

Q: A sheet of copper is stretched biaxially in the xy-plane. If the strair are e = 0.40 × 10-³ and e, =...

A: Given Data : Copper sheet Strains are : εx=0.40×10-3εy=0.30×10-3 E=110 GPav=0.35

Q: Question 4 ) Listen AV-belt is wrapped around a Ø5.00-inch pulley with a 38.0° groove angle. Calcula...

A: Given data-angle in degree for belt wrap=38.0°C

Q: An aircraft travelling at 600 km/h accelerates steadily at 10 km/h per second. Taking the speed of s...

A:

Q: If the motor draws in the cable with an acceleration of 3 m/s^2, determine the reactions at the supp...

A:

Q: Callulate the bendung Shiessimeitd)eBmen inictral monont of 23.Sual-m is opplied to a cDES, sechions...

A: Answer: The bending stress at point B is 11.2126 MPa.

Q: The time taken to drill a hole through a 30mm thick plate with the drill rotating at 200 rpm and mov...

A: Given Data: The thickness of the plate, t=30 mm

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.