Consider the instruction Load 200. Given the following memory and register R1 contents: Memory 120 200 400 600 800 350 600 900 400 250 Assume R1 is implied in the indexed addressing mode. Determine the actual value loaded into the accumulator (AC) for each of the following addressing modes: Mode Immediate Direct Indirect Indexed R1 600 Value Loaded into AC

Consider the instruction Load 200. Given the following memory and register R1 contents: Memory 120 200 400 600 800 350 600 900 400 250 Assume R1 is implied in the indexed addressing mode. Determine the actual value loaded into the accumulator (AC) for each of the following addressing modes: Mode Immediate Direct Indirect Indexed R1 600 Value Loaded into AC

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 12VE

See similar textbooks

Similar questions

5. Load the register (CL) from the memory location [0500H] then subtract the content of this register from the accumulator (AL). Correct the result as a (BCD) numbers . Let [0500H] = 12H & AL = 3FH %3D
Given a memory load instruction, "mov R0; [R1+1000]," please give the input that should be selectedat each multiplexer. You can write "none" for the multiplexers that are not used for this instruction.(a) MUX1:(b) MUX2:(c) MUX3:(d) MUX4:
4. Which segment will be accessed for the instruction MOV [BX],AH.
(d) The table below shows the ALUcontrol signal of the datapath we discussed in class. Instruction Funct ALU Орсode ALUop ALU action operation field control Iw 00 load word XXXXXX add 0010 Sw 00 store word XXXXXX add 0010 beq 01 branch equal subtract 0110 XXXXXX R-type 10 add 100000 add 0010 R-type 10 subtract 100010 subtract 0110 R-type 10 AND 100100 AND 0000 R-type 10 OR 100101 OR 0001 R-type 10 set on less than 101010 set on less than 0111 You want to add the bne instruction into the datapath, which already includes the required hardware for the instruction. Write out the ALUop for bne and how you can determine whether the bne results in the branch to be taken.
Indirect Addressing Mode Instruction 002A J@ RETADR Instruction Starts with 002A Opcode of J is 30 Object code is 3E2003 Show the detail work to get the above object code from the instruction.
Q2- Write a program in assembly language for the 8085 microprocessor to receive one byte of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When receive the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception(start bits 1 1 ), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit 0 ). The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time
Computers use addressing mode strategies for Specifying rules for modifying or interpreting address field of the instruction giving programming versatility to the user by providing facilities as pointers to memory counters for loop control All the above To reduce no. of bits in the field of instruction
"uppose we have the instruction Load 500. Given that memory and register R1 contain the values below: Memory Ox100 Ox600 R1 Ox200 Ox400 Охз00 ОхБ00 Ox 100 Ох600 Ox500 Ox700 Ох800 and assuming that Ra is implied in the indexed addressing mode, determine the actual value loaded into the accumulator and fill in the table below: Mode Value Loaded into AC Immediate Direct Indirect Indexed
Complete the following table: MIPS Instruction op code rs rt rd shamt funct imm. /address Hexadecimal Representation add $t4, $s2, $s1 addi $s0, $t0, 123 lw $s6, -88($t7) Note: In MIPS register file, temporary registers $t0-$t7 have indices 8-15 (respec- tively). Also, the saved registers $s0-$s7 have indices 16-23 (respectively).
In SIC/XE specification of instructions set, the location of the address of operand is given by the addressing modes of the instruction. Given the format 3 Instruction format below, extensively deduce all the possibleaddressing modes
Q1:/ Show the contents in hexadecimal of registers PC, AR, DR, AC, IR and SC of the basic computer when an instruction at address 021 in the basic computer has I = 1, an operation code of the ADD instruction, and an address part equal to 051. The memory word at address 051 contains 0083. The memory word at address 083 contains B8F2. The memory word at address 038 contains A837 and the content of AC is A937. Give the answer in a table with six columns, one for each register and a row for each timing signal. (All numbers are in hexadecimal) uipors - ea
Using the following data definitions: bytel BYTE byte2 BYTE word1 WORD word2 WORD 3 OFFh, 1, 2 14h OFFFFh, 1, 2 word3 SWORD 7FFFh, 8000h word4 SWORD 9000h dword1 DWORD 10h, 20h, 30h, 40h dArray DWORD 10 DUP (?) Write an instruction that moves the lower 8 bits of word2 into the AL register.