consider a cylindrical nickle wire 1.9 mm in diameter and 3.0*104 mm long. calculate its elongation when a load of 260 N is applied. Asuume that the deformation is totally elastic and that the eleastic modulus for nickel is 207 GPa (or 207* 109 N/m2)

consider a cylindrical nickle wire 1.9 mm in diameter and 3.0104 mm long. calculate its elongation when a load of 260 N is applied. Asuume that the deformation is totally elastic and that the eleastic modulus for nickel is 207 GPa (or 207 109 N/m2)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Related questions

Q: Muscle moment arm = 5 cm = d Weight of load = 10 kg Weight of torso = 50 kg a) What is the Moment of…

A: The moment of the load to torso is given by,Mload to torso =Wload x h + Wtorsox bWhere,Wtorso =…

Q: A tensile load of 40 kN is acting on a rod of diameter 40 mm and of length 4m. A bore of diameter 20…

Q: Relative Motion Analysis using Rotating Axes, use the formulas attached to find the solution to the…

A: Dear Students

Q: Problem: Draw a pneumatic valve circuit to implement the function - T = A.B.C + A.C' + B.C'.

A: To find:Pneumatic valve circuit to implement the function.

Q: you are analyzing the maximum stress of a rectangular cross-section beam supported at both ends with…

A: The maximum stress in a rectangular cross-section beam supported at both ends with a single load in…

Q: Block A weighing 25 N collides with block B, which is at rest, with a speed of 30 m/sec. Block B…

Q: onsider the robotic arm shown below, made up of individual arms ?B and ?C. The weight of the arms AB…

Q: Figure below shows a dryer operating at steady state. Damp fabric containing 60% moisture by mass…

Q: Q2. A 2 lb of steam, initially at 700 lbf/in.², 550°F undergoes a polytropic process in a piston-…

A: The mass of the steam, The initial pressure, The initial temperature, The final pressure, The…

Q: termine the moments of inertia I, and I, of the area e area, if a 2.5 in. 1.2 in. 5.0 in. B

A: The properties of rectangle 1-The properties of the rectangle 2-

Q: The principal stresses at a point P in a solid are 70 MPa, -70 MPa and 0. The yield stress of the…

A: In solid mechanics, when a material is subjected to external forces, it experiences internal…

Q: A uniformly dense rod with a length of 6.9 m and a mass of 6 kg is free to rotate around a…

Q: 3.29 The unit cell for Al₂O3 has hexagonal symme- try with lattice parameters a = 0.4759 nm and c =…

A: Given-Lattice parameter Avogadro Number Atomic mass of aluminium Atomic mass of oxygen Ionic radius…

Q: 3. A uniform, 200-kg plate is kept in static equilibrium by two hinges, A and B, and a single cable,…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 2. The figure shows a traffic-light assembly with three identical 100-lb traffic lights at B, C, and…

Q: What is the coefficient of performance (COP) if the cooling effect is 85,000 Btuh and the power…

A: What is the coefficient of performance (COP).If the cooling effect is 85,000 Btuh and the power…

Q: Consider a material with the stress-strain diagram shown (similar to a generic metal, but…

A: Given-Stress Strain curveTo Find-Modulus of toughness

Q: 3 mol of air are contained in a piston-cylinder system with a surface of S = 5 m², loaded with a…

Q: Find the constraint acceleration equation between block A and B (Assume all upper and down pulleys'…

Q: Calculate the change in internal energy of air with a temperature increase from 400 K to 700 K…

Q: A 3.5 inch diameter aluminum bar has Su = 45 ksi and Sy = 40 ksi and machined surfaces. Estimate the…

Q: At an amusement park there are 200-kg bumper cars A, B, and C that have riders with masses of 45 kg,…

Q: 1. A stainless steel rod (18% Cr, 8 % Ni) 6.4 mm diameter is initially at a uniform temperature of…

Q: EXAMPLE 6.8 Draw the shear and moment diagrams for the cantilever beam in Fig. 6-15a. 2 kN 2 m 1.5…

Q: An engineer would like to create a formula to determine the force exerted by a river flow on a…

Q: A - 150 kip-ft (negative 150 kip-feet) moment is acting at the centroid of the cross section shown…

A: Given:To find:

Q: T For the Robot and work frame shown, the following matrices are given: T, T and $T. Compute = [B]…

Q: *4-15. Determine handle of the the moment of each force acting on the wrench about the z axis. Take…

A: To find:The moment about the axis.Given:The forces are .

Q: Stress ( σ =F/A) F=? in N B) Direct Shear ( τ =V/A) V=? in N C) Transverse Shear ( τ =3V/2A) V=?…

Q: In the casting of steel in the sand mold conditions, the mold constant in Chvorinov's rule is given…

Q: 2. 240 mm 160 mm 240 min 240 mm 240 mm A uniform pipe cover of radius r= 240 mm and mass 30 kg is…

Q: Find the reaction forces & cables forces & cables total length

A: Find the reaction forces & cables forces & cables total length.

Q: The wheel rolls without slipping such that at the instant shown it has an angular velocity w and…

A: Let's first draw the free-body diagram of the wheel.

Q: 4-32. If the resultant couple moment of the three couples acting on the triangular block is to be…

A: The resultant couple moment on triangular block is zero.

Q: A rigid body system shown in Figure 1 below. Use u(t) as the degree of freedom (DOF) of the system.…

Q: 4. Determine the composition range in which the Tl-Pb alloy at 350°C is (a) fully liquid, (b) fully…

Q: is subjected to a triaxial loading consisting of a uniformly distributed tensile forces of 200 kN in…

Q: A mass m = 1 kg spins around a vertical pole in a circular path at a constant speed and, at the…

Q: 3. A uniform, 200-kg plate is kept in static equilibrium by two hinges, A and B, and a single cable,…

A: The mass of plate is DCE is a single cable.

Q: Part B - Normal strain, cross-sectional area, load, and Poisson's ratio Four axially loaded members…

A: There are four cases in which all the components have different cross sectional areas and load and…

Q: 23. Two blocks are stacked on top of each other on the floor. The friction coefficient is 0.2…

Q: Lead FCC Structure and Atomic Radius, r = 1.746. Find the Distance between the planes (200), (220)…

Q: Water flows at a rate of 2.4 ft3/s in an old, rusty 7.8-in.-diameter pipe that has a relative…

A: Given;

Q: α b Giren smeath rad of length 36, that weight 38N. what is the angle af to keep the system Static,…

Q: A composite beam consists of a nforced with a materi 2 strip bonded to the bottom surface as shown.…

A: The elastic modulus of material 1 is .The elastic modulus of material 2 is .The dimension are .The…

Q: velocity with which the golf ball leaves th second

A: To determine the velocitywhere, mass of the golf club , mass of the ball, striking force time…

Q: Consider the following face-centered-cubic dislocation reaction: (110) [21]+(121) 2 (a) Given [b]= z…

A: The Initial dislocation is,u = 1, v= 1 and z =0.Therefore,

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD. The wire has a diameter of 0.27…

Q: Use the method of images to approximate the flow pattern past a cylinder a distance 4a from a single…

A: Given:To find:Approximate the flow pattern past the cylinder.

Q: An aircraft component, made of 7075-T6 aluminum alloy, can be represented as a bar of diameter 20 mm…

Concept explainers

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.

Question

100%

consider a cylindrical nickle wire 1.9 mm in diameter and 3.0*10⁴ mm long. calculate its elongation when a load of 260 N is applied. Asuume that the deformation is totally elastic and that the eleastic modulus for nickel is 207 GPa (or 207* 10⁹ N/m²)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the given variable

VIEW

Step 2: Calculate the elongation of the cylindrical nickle wire

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A. Calculate the axial deformation of a steel rod 20 cm long, 10 cm diameter. If an axial loading 300 MPa is applied at the end. B. If the cross-sectional is square with t=10 mm, is the deformation will be higher or lower. (use E=200 GPa) * Vour onouIor
A rod is subjected to a uniaxial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. Calculate the modulus of rigidity if the poisson's ratio is 0.3.
A steel (E=30x106 psi) rod 10m long and 5cm in diameter is subjected to a compressive force of F=1000 N. Find the deformation of the rod.
A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. If the Poisson's ratio of the rod is 0.3, calculate the modulus of rigidity.
The original length of a piece of metal is 400 mm, this piece has pulled in tension with stress of 370 MPa. If the elastic modulus is 120 GPa what is the resultant elongation
A plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of the bars is 80. If the allowable shear strain in the plastic is 0.014 radian, what is the minimum permissible length of the bar in mm?
A plastic bar of 53 mm is to be twisted by torques T until the angle of rotation between the ends of the bars is 9 degree. If the allowable shear strain in the plastic is 0.018 radian, what is the minimum permissible length of the bar in mm?
2. Consider a cylindrical nickel wire 0.08 in. in diameter and 1200 in. long. Calculate its elongation when a load of 300 N is applied. Assume that the deformation is totally elastic. 3. A cylindrical specimen of a metal alloy 10 mm in diameter is stressed elastically in tension. A force of 3370 Ibr produces a reduction in specimen diameter of 7 x 10* mm. Compute Poisson's ratio for this material if its elastic modulus is 100 GPa. 4. A cylindrical specimen of a hypothetical metal alloy is stressed in compression. If its original and final diameters are 20.000 and 20.025 mm, respectively, and its final length is 74.96 mm, compute its original length if the deformation is totally elastic. The elastic and shear moduli for this alloy are 105 GPa and 39.7 GPa, respectively.
10-mm-diameter rod of 3003-H14 aluminium alloy is subjected to a 6-kN tensile load. Calculate the resulting rod diameter. Calculate the diameter if this rod is subjected to a 6-kN compressive load, given that the elastic modulus =70 GPa and poisson ratio=0.33
A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. If the Poisson's ratio of the rod is 0.3, the modulus of rigidity (in GPa) is