5 (five) samples / specimens of solid brick units having height = h, length = b, and width = t,compressive load P as shown in Table 1 below.Table 1. Experimental resultsLength b(cm)Compressiveload PWidth tHeight h(cm)Sample(cm)(ton-f)11111.111.314.98211.311.311.215.52311.411.211.315.8541111.31111.114.91511.211.214.79If the compressive strength is the average P divided by the cross-sectional area of thecompressed sample, calculate the average compressive strength f»r' in MPa of the brick(show your calculations). 1 ton-force =10 kN.Ph

Answered: Image /qna-images/answer/2b1de872-a544-4908-b7d4-00bd065bba38.jpg

Answered: compressive load P as shown in Table 1…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Civil Engineering help Table 1 Test No. Rate of deformation Avg. sample length (mm) Avg. sample diameter (mm) Ring factor Cell pressure (kPa) (mm/min). (AIP/N) 100 74.7 38.1 1.27 0.9845 400 75.3 37.7 Table 2 Deformation (mm) Force gauge (divisions) Test 1 Test 2 0.5 22 24 1.0 46 44 1.5 2.0 62 68 80 82 2.5 102 106 132 3.0 121 134 3.5 149 4.0 157 173 5.0 6.0 7.0 182 200 219 231 241 194 195 8.0 197 90 198 200 199 | 196 246 10.0 252 251 244 11.0 12.0 By producing Mohr circles and deviatoric stress vs axial strain plots of the tests using the data presented, determine the average Young's modulus, E (MPa) from the most linear portion of the tests deviatoric stress vs axial strain nints Enterani l ...
Determine the compressive strength of each sample blocks below. Given the area of the block to be 80,000 mm^2. After determining each compressive strength, determine the average compressive strength of the sample blocks and express your answer in PSI. SAMPLE NO. FORCE (N) COMPRESSIVE STRENGTH 1 3500 2 4200 3 4500 4 5000 5450 6. 6000 7 6500 8 6745
2. Data for calculating compressive strength: Ø Tested material – cement paste Ø Force destroying the specimen (first half of the beam), Fc1 – 25900 N Ø Force destroying the specimen (first half of the beam), Fc2 – 26300 N Calculate compressive strength
How many grams (whole number, no need for unit) of fine aggregates used in this experiment? Blank 1 Blank 1 Add your answer
Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A and B are tested to failure in tension. (a) At failure the distances between the gage marks are LAf 2.90 in. and LBf 2.22 in.; the corresponding diameters at the failure cross sections are dAf 0.263 in. and dBf 0.471 in., respectively. Determine the percent elongation in 2 in. and the percent reduction in area for these two materials, and classify each material as either brittle or ductile. (b) From these tensile tests the following data are also obtained: EA 10.0 103 ksi, (Y)A 5 ksi, (U)A 13 ksi; EB 10.4 103 ksi, (Y)B 73 ksi, (U)B 83 ksi. From the data given here, make rough sketches (to scale) of the stress-strain diagrams of materials A and B.
A concrete beam sample has a width of 5 inches, a depth of 6 inches, and a length of 20 inches. The sample was tested for ASTM C293. The maximum load carried by the sample after its failure is 95 KN. Determine the modulus of rupture of the sample in psi. (use 1lbf = 4.45 N, round-up your answer to the nearest whole number that is divisible by 5, no need for unit)
1.46: A contractor claims that the mean compressive strength for a concrete mix is 5000 psi (μ) and that it has a standard deviation of 400 psi (σ). If you break 20 cylinders (N) and obtain a mean compressive strength of 4,800 psi (m), would you believe the contractor’s claim? Why? (Hint; Use statistical t-test.) Next, what is the maximum number of breaks (N) that could be performed that WOULD make you believe the contractor’s claim? Assume that the results wouldn’t change, i.e. σ = 400 psi and m = 4,800 psi. Recall that the equation to find the lower bound of a one sided distribution is LB = μ - (tσ)* σ/(N^0.5) Because the sample size is relatively small, use the ‘student t test’ to represent the normal distribution. You should have at least 95% confidence in the results. That means that α = 0.05. Keep in mind that this is a one tailed distribution, since we only care about the lower bound (i.e. meaning that we are only concerned about concrete that doesn’t meet our minimum strength…
compute for the modulus of ruptiure of the concrete beam sample is 6"x6" and the span length of the beam (support to support) is equivalent to the 3 times the depth of the beam. load applied is 65.5 kN at center. a. 11.6 MPa b. 14.9 MPa c. 12.7 MPa d. 13.1 MPa
Determine Given the following tabulated data representing a sample from a concrete mix used in a project. The arithmetic mean (x) is approximately. Compressive Strength (MPa) Frequency 15 18 21 24 27 30 3 4 4 3 21 MPa 22 MPa 23 MPa 25 MPa O
Home The compressive strength of samples of cement can be modeled by a normal distribution with a mean, , of 6000 kg/cm² and a standard deviation, o, of 100 kg/cm². (a) What is the probability that a sample's strength is less than 6250 kg/cm²? Ans. 0.9938. (b) What is the probability that a sample's strength is between 5800 and 5900 kg/cm²? Ans. 0.1359 (c) What strength is exceeded by 95% of the samples? Ans. 5836.5
Two 150 mm * 300 mm concrete cylinders with randomly oriented steelfiber contents of 0 and 2% by weight, respectively. After curing for 28 days,the specimens were subjected to increments of compressive loads until failure. The load versus deformation results were as shown in Table P7.45. Assuming that the gauge length is the whole specimen height, determine the following:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for the two specimens on one graph.c. The initial modulus of elasticity for each specimen.d. The ultimate strength for each specimen.e. The strain at failure for each specimen.f. Toughness. Curves may be approximated with a series of straight lines.g. Comment on the effect of adding fiber on the following:i. Modulus of elasticityii. Ultimate strengthiii. Ductilityiv. Toughness
Situation 3 A compressive strength test were conducted to the following cylinder; Cylinder 1 3015 psi Cylinder 2 2950 psi Cylinder 3 3253 psi Cylinder 4 3004 psi Cylinder 5 3031 psi It is observed that the size of the cylinder is 6% in x 12" which is much bigger that the standard cylinder specimen. 1. What would be the reported compressive strength for each cylinder. 2. What is the average compressive strength? 3. If the target compressive strength at: 3 days is 3000 psi, What can you say about the test result?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS