A series circuit is arranged with the following components arranged clockwise with the battery starting on the left side: 10 V battery, 2 ohm resistor,5 ohm bulb.Where in the circuit would a measurement for current produce the highest value?O Between the battery's positive terminal and the 2 ohm resistorO Between the 2 ohm resistor and the 5 ohm bulbO Between the 5 ohm bulb and the battery's negative terminalO The current is the same at all points in the circuit.

Answered: Image /qna-images/answer/a8ecec1f-8cd4-4c48-b46c-481ba38e6e33.jpg

circuit is arranged with the following components arranged clockwise with the battery starting on the left side: 10 V battery, 2 ohm resistor, ulb. n the circuit would a measurement for current produce the highest value? en the battery's positive terminal and the 2 ohm resistor en the 2 ohm resistor and the 5 ohm bulb en the 5 ohm bulb and the battery's negative terminal rrent is the same at all points in the circuit.

circuit is arranged with the following components arranged clockwise with the battery starting on the left side: 10 V battery, 2 ohm resistor, ulb. n the circuit would a measurement for current produce the highest value? en the battery's positive terminal and the 2 ohm resistor en the 2 ohm resistor and the 5 ohm bulb en the 5 ohm bulb and the battery's negative terminal rrent is the same at all points in the circuit.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 74AP: Consider a circuit that consists of a real battery with an emf and an internal resistance of r...

See similar textbooks

Similar questions

Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.6 V when it is delivering 20.0 W of power to an external load resistor R. (a) What is the value of R? (b) What is the internal resistance of the battery?
Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?
A 160F capacitor charged to 450 V is dischargedthrough a 31.2k resistor, (a) Find the time constant.(b)Calculate the temperature increase of the resistor, given that its mass is 2.50 g and its specific heat is 1.67kJ/kg °C,noting that most of the thermal energy is retained in the short time of the discharge, (c) Calculate the new resistance, assuming it is pure carbon. (d) Does this change in resistance seem significant?
Why is the following situation impossible? A technician is testing a circuit that contains a resistance R. He realizes that a better design for the circuit would include a resistance 73R rather than R. He has three additional resistors, each with resistance R. By combining these additional resistors in a certain combination that is then placed in series with the original resistor, he achieves the desired resistance.
Consider the circuits shown below, (a) What is the current through each resistor in part (a)? (b) What is the current through each resistor in part (b)? (c) What is the power dissipated or consumed by each circuit? (d) What is the power supplied to each circuit?
The- pair of capacitors in Figure P28.63 are fully charged by a 12.0-V battery. The battery is disconnected, and the switch is then closed. Alter 1.00 ms has elapsed, (a) how much charge remains 011 the 3.00-F capacitor? (b) How much charge remains on the 2.00-F capacitor? (c) What is the current in the resistor at this time?
Consider the circuit shown in Figure P21.39. Find (a) the current in the 20.0- resistor and (b) the potential difference between points a and b. Figure P21.39
The circuit in Figure P27.34a consists of three resistors and one battery with no internal resistance. (a) Find the current in the 5.00- resistor. (b) Find the power delivered to the 5.00- resistor. (c) In each of the circuits in Figures P27.34b, P27.34c, and P27.34d, an additional 15.0-V battery has been inserted into the circuit. Which diagram or diagrams represent a circuit that requires the use of Kirchhoffs rules to find the currents? Explain why. (d) In which of these three new circuits is the smallest amount of power delivered to the 10.0- resistor? (You need not calculate the power in each circuit if you explain your answer.) Figure P27.34
For the purpose of measuring the electric resistance of shoes through the body of the wearer standing on a metal ground plate, the American National Standards Institute (ANSI) specifies the circuit shown in Figure P27.14. The potential difference V across the 1.00-M resistor is measured with an ideal voltmeter. (a) Show that the resistance of the footwear is Rshoes=50.0VVV (b) In a medical test, a current through the human body should not exceed 150 A. Can the current delivered by the ANSI-specified circuit exceed 150 A? To decide, consider a person standing barefoot on the ground plate. Figure P27.14
A car battery with a 12-V emf and an internal resistance of 0.050 is being charged with a current of 60 A. Note that in this process the battery is being charged. (a) What is the potential difference across its terminals? (b) At what rate is thermal energy being dissipated in the battery? (c) At what rate is electric energy being converted to chemical energy? (d) What are the answers to (a) and (b) when the battery is used to supply 60 A to the starter motor?
A child's electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 inseries with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and itsbatteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?