Calculate the equivalent standard axle for each truck based on ATJ 5/85 (2013). Arrange the truck from the highest equivalent standard axle to the lowest equivalent standard axle. Truck A having 2 axles with BG1 =7000kg and BG2 = 8000kg Truck B having 3 axles with BG1 = 3000kg, BG2 = 4000kg and BG3= 4000kg Truck C having 4 axles with BG1= 3000kg, BG2 = 3000kg, BG3= 4000kg and BG4= 4000kg O Truck A > Truck B> Truck C O Truck C > Truck B> Truck A Truck A > Truck C > Truck B O Truck B > Truck C> Truck A

Calculate the equivalent standard axle for each truck based on ATJ 5/85 (2013). Arrange the truck from the highest equivalent standard axle to the lowest equivalent standard axle. Truck A having 2 axles with BG1 =7000kg and BG2 = 8000kg Truck B having 3 axles with BG1 = 3000kg, BG2 = 4000kg and BG3= 4000kg Truck C having 4 axles with BG1= 3000kg, BG2 = 3000kg, BG3= 4000kg and BG4= 4000kg O Truck A > Truck B> Truck C O Truck C > Truck B> Truck A Truck A > Truck C > Truck B O Truck B > Truck C> Truck A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the type of loading gear configurations of Boeing 747 aircraft ( double twin tandem gear), the number of axles in the main gear will be ..
1. Determine if a rubber-tired truck can operate under the following conditions: Total weight of truck: 12,000kg Driving surface: snow, packed Maximum rimpull @ sea level = 9,000 kg Altitude of operation = 3000m Required pull is 4000kg
(1) (2) cr cr EI 3 EI 4 L2 Determine the L2/L, ratio so that the Column (1) will have an elastic buckling load three times the Column (2) has. Express your answer using three significant figures.
This is a type of load varies in length when getting the maximum internal forces of a structure. O Axle Loads O Moving load O Dead Load O Live Load
The rear Axles of the H20-44 Truck carries percent of the total weight.
Question What will be the equivalent axle load factor for an axle load of 300 kN if the standard axle load is 100 KN?
The ordinates of an influence line for reaction of a simply supported beam will exceed 1.0 O True O False
Define the following terminologies: i. Structural Number (SN) ii. Equivalent Single Axle Load (ESAL)iii. Modulus of Subgrade Reaction (k)
4.7 PROBLEMS 4.7.3 Axle load study conducted on a stretch of road in 2017 yield theşe results: Axle load range (ton) 2 - 4 4 - 6 6 -8 8 - 10 10 - 12 12 – 14 No. of axle 500 710 599 621 452 168 Number of commercial vehicles for the particular day is 1860. Based on Road Note 31, determine: a) Average number of axle per commercial vehicle; b) Total equivalent standard axle for that particular day; c) Average number of standard axle per commercial vehicle; and d) Average number of standard axle per commercial axle.
1: The questions vary with the student number. Each student has to solve the questions considering his or her student ID. Use "A" as last number of your student ID. If it is zero, please take that value as 5 instead of zero. Am The W250*67 is made of A992 steel and is used as a column that has a length of A m. If the ends of the column are fixed supported, a) Determine critical load b) Can the column support the critical load without yielding? Area=8560 mm? E=200 GPa L=104*10 mm -22.2*10 mm Yield Strength of Steel= 345 MPa 'x-X y-y
3. The tow truck’s front wheel will be lifted off the ground if the moment of the load W about the rear axle exceeds the moment of the 6200-lb weight of the truck. Determine the largest Wthat may be safely carried by the tow truck.
Assuming a structural number of 3, how many times more damaging is an 80 kip tandem axle than a 28 kip single axle?