Hello sir, parts 1-8 are all from the same problem The d= 12-mm-diameter solid rod passes through a D= 20-mm-diameter hole in the support plate. When a load Pis applied to therod, the rod head rests on the support plate. The support plate has a thickness of b = 13 mm. The rod head has a diameter of a = 29mm, and the head has a thickness of t= 8 mm. If the normal stress produced in the rod by load Pis 225 MPa, determine(a) the bearing stress acting between the support plate and the rod head.(b) the average shear stress produced in the rod head.(c) the punching shear stress produced in the support plate by the rod head.SupportPlate- Hole diameter DRodHeadCalculate the cross-sectional area of the rod.Answer: Arod =mm2Attempts: 1 of 1 usedPart 2Calculate the tension force in the rod.Answer: Frod = 1NSave for LaterAttempts: 0 of 1usedSubmit AnswerPart 3Calculate the contact area between the support plate and the rod head.Answer: Agontact=mm?Save for LaterAttempts: 0 of 1 used Submit Answer Part 4Calculate the bearing stress between the support plate and the rod head.Answer: O =MPaAttempts: 0 of 1used Submit AnswerSave for LaterPart 5Calculate the area subjected to shear stress in the rod head.Answer: Av-rod haad =mm?Save for LaterAttempts: 0 of 1usedSubmlt AnswerPart 6Calculate the average shear stress in the rod head.Answer: T=MPaSave for LaterAttempts: 0 of 1 usedSubmit AnswerPart 7Calculate the area subjected to punching shear stress produced in the support plate by the rod head.Answer: Av-piase =imm?Save for LaterAttempts: 0 of 1 used Submit AnswerPart 8Calculate the average punching shear stress in the support plateAnswer: T=MPaSave for LaterAttempts: 0 of 1 usedSubmlt Answer

Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts of a…

Answered: Calculate the cross-sectional area of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The d = 13-mm-diameter solid rod passes through a D = 20-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 15 mm. The rod head has a diameter of a = 31 mm, and the head has a thickness of t= 10 mm. If the normal stress produced in the rod by load Pis 150 MPa, determine (a) the bearing stress acting between the support plate and the rod head. (b) the average shear stress produced in the rod head. (c) the punching shear stress produced in the support plate by the rod head. Support Plate - Hole diameter D P Rod Нead a Calculate the cross-sectional area of the rod. Answer: Arod = i mm2
The d = 15-mm-diameter solid rod passes through a D = 20-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 15 mm. The rod head has a diameter of a = 30 mm, and the head has a thickness of t = 9 mm. If the normal stress produced in the rod by load P is 200 MPa, determine (a) the bearing stress acting between the support plate and the rod head. (b) the average shear stress produced in the rod head. (c) the punching shear stress produced in the support plate by the rod head. Support Plate Hole diameter D Rod Head Calculate the cross-sectional area of the rod. Answer: Arodi mm²
The d - 15-mm-diameter solid rod passes through a D=20-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b- 13 mm. The rod head has a diameter of a = 30 mm, and the head has a thickness of t= 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 90 MPa, and the bearing stress between the rod head and the support plate cannot exceed 140 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Rod Answer: Pmax i -Hole diameter D Head kN ام
The d = 16-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 32 mm, and the head has a thickness of t= 10 mm. The shear stress in the rod head cannot exceed 135 MPa, the punching shear stress in the support plate cannot exceed 80 MPa, and the bearing stress between the rod head and the support plate cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate - Hole diameter D d a Rod Неad b
The vertical shaft with a diameter of d = 20 mm is supported by a thrust collar that rests on a 21-mm-thick plate. The thrust collar is 16-mm thick. Assume that the load P causes a compressive stress of 190 MPa in the shaft. If the bearing stress between the thrust collar and the plate is limited to 35 MPa, determine the minimum outer diameter Dcollar that must be used for the thrust collar. Thrust collar area Plate Thrust collar d Dcollar
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 10 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 8 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 100 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t= 10 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 125 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate -Hole diameter D a Rod Нead Answer: Pmax i kN
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B. and the the bearing stress in the bell crank at B.
The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Express your answer in Ib. 4 in. 3.5 in. 4/4 7 in.
The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial distributed loading along its length of w = 8 kN/m. Two concentrated loads also act on the rod: P = 5 kN and Q = 7 kN. Determine the normal stress in the rod at x = 1.4 m. Assume a = 0.5 m and b = 1.2 m. A -> a Answer: 0 = i B W b C MPa Q
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths.
The bolt has a diameter of 20 (mm) and passes through a tube that has an inner diameter of 50 (mm) and an outer diameter of 60 (mm). If the bolt and tube are made of A-36 steel, determine the normal stress in the tube and bolt when a force of 40 (kN) is applied to the bolt. Assume the end caps are rigid. 160 mm 40 kN 40 kN 150 mm

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS