B- Show (for both 1 and 2) the content of CL register, OF, SF, ZF, and CF afterexecution the following sequence of instruction:1-MOV AL, 852- MOV AL, - 52MOV CL, 70MOV CL, -9ADD CL, ALADD CL, ALIs the result correct, why?

Given: We are given two sets of instructions. Goal: We have to find out the content of register…

B- Show (for both 1 and 2) the content of CL register, OF, SF, ZF, and CF after exccution the following sequence of instruction: I-MOV AL , 85| 2- MOV AL, - 52 MOV CL, 70 MOV CL, -9 ADD CL, AL ADD CL, AL

B- Show (for both 1 and 2) the content of CL register, OF, SF, ZF, and CF after exccution the following sequence of instruction: I-MOV AL , 85| 2- MOV AL, - 52 MOV CL, 70 MOV CL, -9 ADD CL, AL ADD CL, AL

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Q: Without using (SUB) instruction, write an assembly program to compute W from the following equation:…

A: the solution is an given below :

Q: Verify the operation of instruction. JMP BX Assume the content of BX is 0010 H.

A: JMP BX : jump to the address whose value is in BX.

Q: Develop an 8051 ALP to transfer data from code space starting at address 200H to RAM locations…

A: the answer is given below:-

Q: Write an assembly code to rotate a stepper motor with three main terminals in counter clockwise dual…

A: The Answer is

Q: Question 6: A circuit with two outputs has to implement the following functions f(x1, .... x4) =…

Q: If DI content equal 3000H then Instruction MOV AX, (DI) does the followings:

A: Please check the step 2 for solution

Q: 21) Determine the contents of the registers and the carry flag after execution the following…

A: According to the information given:- we have to execute the given statement in order to find the…

Q: (a)(i) Flip-flops are basic memory element used in sequential circuits. Flip-flop has two stable…

A: Given: (a) (i) Flip-flops are basic memory element used in sequential circuits. Flip-flop has two…

Q: 12. Implement F(X,X,Z)= Zm(2,3,4,7) using multiplexer.

A: Here in this question we have asked to implement some given function using multiplexer.

Q: Ex. Described each line and write the equation of PA for the follow assembly code: 01 org 100h 02…

Q: elect the instruction sequence that will add 4 5 times using a loop struct Choice 1: mov ax, 0 mov…

A: Hey there, I am writing the required solution of the above stated question.Please do find the…

Q: Q 4. G 10 contents of BC register pair with DE register pair without using MOV instructions. Using…

A: The content of the register will be exchanged by using Push and Pop . Algorithm - Step 01 -…

Q: 4. Consider DFA M = ({91, 92, 93, 94}, {0, 1}, 6, 91, 91, 94}) for 6 defined as the following table.…

A: Hello student I giving this solution as per my best of knowledge and I am sure that this solution…

Q: Using logic gates, design an active low chip select for the memory a 256 K memory device starting at…

A: Number of lines=16 words4 word each=4 linesnumber of blocks64 words4 words each=16 blocksBlock…

Q: Q2/ (Answer Two Only) from the following : 1- Implement ( without simplification) F= (A+B).(C+A.D)…

Q: 1. Question 1: a) Explain the difference between CMP and SUB instruction b) What is the last…

A: Below is the answer to above question. I hope this will be helpful for you...

Q: 4. Using shift and add instruction, achieve multiply $s1 with 65

A: Actually, 0,s and 1's are called as binary numbers.

Q: Example 4: Write instruction to load the number 2050H in the register pair BC. Increment the number…

A: The question is to write the answer of the question related to to 8085 microprocessor.

Q: Now calculate the relative performance of adders. Assume that hardware corresponding to any equation…

Q: MOV BL,AL has the following instruction format feilds REG= 000 MOD=11 R/M=011 , the byte 2 will be :

A: 1)C2)B

Q: of a CPU, the een increased point unit has erall speedup r of fixed point ons is 4:6 and to take…

Q: Introduction to embedded systems! Register r1 holds a C variable x of unsigned int type. Translate…

A: We can use lea instruction to multiply instead MUL, which is mainly used to place the adress…

Q: I by using the instruction set encode these instructions in machine code. 1- ADD AX, [Si] 2- MOV AX,…

A: MOV is a 16 bit instruction. The 11-16 bit MSB's are set to OPCODE that is 100010. The 10th bit MSB…

Q: 15. Consider the logic function f(x.y.z) = Em(0,1,4,5) a Build the Truth Table of f. xy zf b.…

Q: E. In an instruction pipeline of 10 ns clock the memory instruction takes 2-stalls while branch…

A: Given:

Q: d. Given DS = 7FA2(H) and Offset is 438E(H), and for instruction %3D

A: Solution a) The Physical Address is - 7FA20+438E = 83DAE Solution b) The Lower Range - 7FA20(7FA20 +…

Q: of 10H, of the instruction MOV AL. [BP+SI+10HJ. Which the name of A Q2:- (B) Find the result of the…

A: B)1111_111H+11001011011B =1111_11101001000+110010110110100001 =11101000111+110010110110100001…

Q: erage equal to 3 and B can execute wit average CPI of 5. For the execut of same instruction, which…

A: Solution Option D A is the fastest processor than B It is based on the cpu time of the processor

Q: design an interfacing circuit for the memory to meet the following specification: 1- Microprocessor…

A: Answer:)

Q: 3. Consider the function F(a, b, c, d) = Em(2, 4, 6, 12, 10) + Ed(0, 8, 9, 13) Implement F using the…

Q: - is used to exchange the content of memory * location [3000], [3001] with DX register The…

A: XCHG DX, [3000H] is the correct option

Q: 2. Using logic gates, design an active low chip select for the memory device described in each of…

A: a) 280000 is euql tro 24 bits 256 K memory is 2^10*2^8=2^18 4 Meg is 2^20*2^2=2^22 Now, Enabling…

Q: Ex. Calculate the PA for the follow assembly code which is assume the DS = 4500h, SS = 2000h, BX %3D…

Q: 2. Load the data 10A10H into DS and ES registers. a. MOV AX,10A10H MOV DS,AX MOV ES,AX b. MOV AX,…

A: We need to load the data 10A10H into registers DS and ES

Q: Develop the Verilog Code to construct a Parallel-Access Shift Register, provide simulation code and…

A: The design of the shift register comprises of five input and single n-bit output. The design is…

Q: Show the assembly instruction for the following machine code, given in hexadecimal. Explain all…

A: Solution for the above question is given in step 2:-

Q: Ex. Described each line and write down the equation of physical add. For the following assembly…

A: The given assembly code is: 01 org 10002 MOV BX+DI, CL03 MOV CH, BX+SI04 MOV AH, BP+DI05 MOV BP+SI,…

Q: 5- Add with carry [BX] to AX register. Suppose BX= 1234h, AX = 3B4FH and the content of the memory…

A: Here, I have added content of register BX with AX. And added with carry.

Q: 2. Using logic gates, design an active low chip select for the memory device described in each of…

A: Answer 2_) a) 280000 is equal to 24 bits256 K memory is 2^10*2^8=2^184 Meg is 2^20*2^2=2^22…

Q: Assume the following register conditions:AX=DEAFh, BX = 1845h, CX = 2255h, DX = 55FFhFind the status…

Q: Compile the RISC-V assembly code for the following C code. Only use registers x8 and x4. Register x8…

A: Given Compile the RISC-V assembly code Mr the following C code. Only use registers and x4. Rgkth,S…

Q: The instruction * JMP 700H is type indirect near direct short direct indirect far direct near…

A: 1) Actually JMP 700 is direct near. The answer is direct near.

Q: Question [2]: Part 1:L An incomplete register circuit is shown in the figure given below. a. Add the…

Q: Show the contents of the related memory locations after the execution of this instruction MOV…

A: Here we write implementation: MOV [BP][SI]+10,DX so here, given DX = 1299H and memory of…

Q: For a function with prototype long decode2(long x, long y, long z); GCC generates the following…

A: C Program code: //include the required header files #include <stdio.h> //prototype of the…

Q: b) Given that the crystal frequency of 8051 Microcontroller is 11.059 megahertz, and one machine…

A: Answer : microcontroller is = 11.059 megahertz crystal frequency of 8051 1 machine cycle take = 12…

Q: Write a short instruction to multiply the content of BL and CL. Load BL with with 10. Store the…

A: 1. loads register BL and CL2. give two example values i.e., 5 and 10.3. it calculates product.4.…

Q: Please show all working. 1. Consider the Boolean function F(A,B, C,D, E) = >…

A: a.) Let the 16x1 Multiplexer has 16 data inputs I15 to I0, four selection lines i.e., s s3 to s0 and…

Q: Write and verify: A structural HDL model for the register described in Problem 6.7.

A: Logic diagram:

Concept explainers

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer. 

Question

B- Show (for both 1 and 2) the content of CL register, OF, SF, ZF, and CF after
execution the following sequence of instruction:
1-MOV AL, 85
2- MOV AL, - 52
MOV CL, 70
MOV CL, -9
ADD CL, AL
ADD CL, AL
Is the result correct, why?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Introduction

VIEW

Solution

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

- Write an assembly code to rotate a stepper motor with three main terminals in counter clockwise dual step. This motor will loop (6) cycles, and the control information will be transferred from memory location (SMX) using lookup table instruction to the system. So that, the memory name should not appear in the loop. Also, save each control word in the stack.
Using a. & b. design FSM for 3-bit shift register and simulate it using C, that can multiply or divide the 3-bit number by 2. code c++
3. a) Consider a counter circuit that contains eight JK FFs wired in the arrangement Q-Q6 Q5Q4Q3Q2QQO (i) Determine the counter's MOD number. (ii) Determine the output frequency in KHz when the input clock frequency is 16 MHz. (iii) What is the range of counting states for this counter? (iv) Assume a starting state (count) of 01100111. What will be the counter's state after 1345 pulses?
Develop the Verilog Code to construct a Parallel-Access Shift Register, provide simulation code and test bench code to demonstrate the cases of: 1. Load is on, all R registers' contents are loaded into Q registers. 2. Shift is on (Not loading), Q registers shift to the right every clock for 4 clocks.
18. In Allen Bradley (AB) Micro850 PLC system, Reverse Contact Instruction can only represent a Normally-Closed (N.C.) input device. (a) True (b) False
RESET M |x = 0, y = 0 f= 1 g = 1 X = 1 f = 0 g = 1 y = X = 1 y = 0 т f= 0 9 = 1 S f = 0 g = 0 X = 0
Write equivalent code of (( CWD )) instruction.
Using D-flip flops, design a 4-bit shift register with parallel load and two control inputs shift andload. The criteria is such that when shift = 1 the contents of the register is shifted by oneposition. New data are transferred into the register when load = 1 andshift = 0. If both inputs are zero, the contents of the register should not change.a. Create a function table for the shift registerb. Design for the next state equation for the D-flip-flops.c. Draw the logic diagram for the ith stage of the 4-bit register
(c) How will your lift controller react if 40 is loaded as a floor number? Discuss the changes you might make to the design for a realistic controller system.. LIBRARY 1ee%; USE ieee.std logic 1164.all; USE leee.std_logic arith.all; architecture behavior of counter is signal IQ: STD LOGIC VECTOR (3 downto 0): begin process (CLK, IQ) begin, 1E (CLX'event and CLK-1') then 4 CLEAR L+0then IQ < "0000 elsif LOAD L 0 then IQ < D; d clear load else IQ < STD LOGIC VECTOR( UNSIGNED(10) 1) end if end process; 0
- Draw the control word format for 8253 timer with proper description of each field - Design a system to explain the digital data transmission using modem - Write the mode instruction format required to program the 8251A USART for asynchronous transmission with 8 data bits, 1 1/2 stop bits, odd parity. and transmitter clock frequency is 19200 Hz and transmit data at 1200Bd.
hello for the MIPS instruction sltiu $s6,$s2,1432, show the immediate number, opcode, rs, and rt in binary in the given order and separated
3) Find the content for the 4-bit shift register of the following sequential circuit during 4 clocks. [The initial value for Q is zero] 1001 CLK a