b) [Research Question] Design a DC battery charger for an electrical vehicle which has a 96 V (nominal) BLDC hub motor which is plugged directly from grid to EV. i) Which type(s) of diode circuit(s) is(are) used for this device. ii) Sketch the input and output waveforms iii) List the needed components for this design.

b) [Research Question] Design a DC battery charger for an electrical vehicle which has a 96 V (nominal) BLDC hub motor which is plugged directly from grid to EV. i) Which type(s) of diode circuit(s) is(are) used for this device. ii) Sketch the input and output waveforms iii) List the needed components for this design.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Assume that an input signal is applied to the circuit given above, as shown in the figure next to it. Accordingly, answer the following questions. The diodes used are silicon diodes, their operating voltages are 0.7 volts, and can be omitted because their resistance is very small. a) Write the name of this circuit, thinking about which circuit we do in the courses is equivalent to the purpose. b) What are the diodes/diodes that are active in a positive half-loop? Please type. c) What are the diodes/diodes active in the negative half-loop? Please type. d) Calculate ? ?−???( ?? ) for this circuit.
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
Hi! Please help me answer this problem our topic here is about Diode in DC & AC Circuits. Please show your correct and complete solution. ASAP! THANK YOUUU!
For the circuit shown in the following figure, Show the state of each transistor and diodes for all the possible inputs. Use a table to write your answer and Find the logical function of the circuit.
One component that does not need to be installed in the correct orientation is a: a. Resistorb. Diodec. Voltage regulatord.
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). (b) Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) Sketch the waveform in A, B, C and D as shown in Figure Q1(a).
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) (b) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
Figure shows a composite switch consisting of a power transistor (BJT) in series with a diode. Assuming that the transistor switch and the diode are ideal, the I-V characteristic of the composite switch is
1. Answer the following with "TRUE" or "FALSE" then explain why. ________a.) Charges choose the path of least resistance. Given a resistor in parallel with a diode, no current willflow through the resistor when the applied voltage exceeds the diode’s forward voltage.________b.) Since diodes are unidirectional components, it will always block AC signals e.g. pulse train,sawtooth, triangular signals.________c.) Silicon diodes typically have a forward voltage of 0.7V.