B) List one engineering applications for which the following physical properties would be considerable:Low melting point:High density:High thermal conductivity:C) Define mechanical properties of a substance.D) List two mechanical properties and two physical that can be measured in the Laboratory and state thedefinition of these properties.E) Which metal exhibited the highest hardness values, Cast iron, mild steel or Zinc? Mention the reasonfor your choice.F) State two common tests used to determine mechanical properties.G) If your phone charger plug passes electric charges to human skin How you can solve the problem? Listthree materials to design the covering.H) Explain corrosion mechanism for electrochemical corrosion of metals ( Galvanic corrosion).I) Mention two other corrosion types other than (Galvanic corrosion) and state the main causes of theselected type (With graphs).J) What are various method of controlling the selected type of corrosion?K) Explain two types of degradation types that may occurred in non-metals.

When a temperature gradient exits perpendicular to the area, thermal conductivity is defined as…

Answered: B) List one engineering applications…

B) List one engineering applications for which the following physical properties would be considerable: Low melting point: High density: High thermal conductivity:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Match the following statements with the term that best describes each statement. (Enter Number ONLY) 1) Hooke's Law 2) Creep 3) Impact Strength 4) Proportional Limit 5) Fatigue 6) Elastic The tendency of a solid material to move slowly or deform permanently under the influence of mechanical stresses below the yield strength of the material. The behavior of materials that deform when loaded but return to their original shape after the load is removed. The linear relationship between stress and strain in the elastic region below the proportional limit. The phenomenon where cracks propagate under loads less than the yield stress due to cyclic loading. The material property determined using the Charpy or Izod test. The point at which the stress vs strain becomes non-linear in an elastic material,
Mechanical Advantage Review Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your engineering design journal. Remember to show all work. 1. A lever has an effort arm that is 8 meters long and the resistance (load) arm that is 5 meters long, how much effort is needed to lift a 200 Newton weight?
When an external force acts on a body, the body tends to undergo some deformation. If the external force is removed and the body comes back to its origin shape and size, the body is known as elastic body. This property, by virtue of which certain materials return back to their original position after the removal of the external force, is called elasticity. We can explain these behaviours using following elastic constants. Young’s modulus or Modulus of elasticity (E) Shear modulus or Modulus of Rigidity (G) Bulk modulus (K) You are required to submit a report explaining these elastic constants and explaining the relations between these elastic constants. (You can use the relation with Poisson’s Ratio and get the relation between E, G and K.)
Which properties are the most helpful in identifyingminerals. Are these properties helpful in the field of engineering? *400 to 500 words FORMAT: i. Introductionii. First body paragraphiii. Second body paragraph... and so oniv. Conclusion
Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m
2) A biomedical company is planning to design a robotic arm from polymeric biomaterials based on their stress-strain curves. You as a bioengineer/researcher in this company, are requested to choose the best material from different biomaterials (A, B, C, D, E, and F) based on their mechanical properties. Express your opinion shortly on the following questions? a) Difference between A and C? b) Difference between B and D? c) Difference between F and E? d) What would be your recommendation for the robotic arm? Why? Stress (MPa) 10.0 7.5 5.0 2.5 0.0 0 C 5 D Strain (%) 10 E F 15
c) Sample of an aluminum alloy has a tensile strength of 175 MPa, What will be the maximum force that can be withstood by a rod of that alloy with a cross-sectional area of 3 cm2?
1-8 Discussions Discuss or explain each of the followings: Effect of the carbon percentage on the shape and magnitude (mechanical properties) of stress-strain curve. 1. 2. Effect of the material heat treatment on the shape and magnitude of the stress-strain curve. 3. Differentiate between the behaviors of metallic and non-metallic materials under tensile test. Affect of prior history of plastic deformation on the shape and magnitude of the stress-strain curve. 4. Effect of the strain rate and temperature on the shape and magnitude of strain curve. 5. the stress- 6. Effect of the material grain size on the shape and magnitude of the stress-strain curve.
Show the typical Stress versus Strain curve for the following materials, and define the materials properties "The stress-strain curve can be used to read off the structural load ability of materials. For many materials, including metals, their loading bearing capability is one of the most important material properties". by reference to the diagram: a) Hammer head is made from hardened tool steel b) Smelter is made from refractory ceramic c) Cable is made from pure copper d) Box is made from polypropylene
ENGINEERING QUESTION- SOLVE FROM SCRATCH! A mass of 450 kg has been hung from the end of a metal wire whose initial length is 1.8 meters and is 1.5 mm in diameter. If the wire is stretched 1.25 cm.a) What were the stress and strain?b) What is Young's modulus?
What could be found equal in both the true and an engineering stress strain curves? Select one: A) Toughness B) Ultimate tensile strength C) Modulus of elasticity D) Hardness E) Strain at fracture